开云体育

I had similar problems two years ago talked with Mark at Palstar he had me put it into a dummy load everything worked normal the next day I replace my alpha DX plus antenna and today I use a hex beam

Further to this, also ensure you have the latest firmware updated. Sent: August 15, 2022 2:20 PM To: [email protected] Subject: Re: [la1k] LA-1K Trips to Standby in SSB mode only I have had

I have had similar issues. Like I said, look at all your other connections and antenna. GL VE6UM Sent: August 15, 2022 2:06 PM To: [email protected] Subject: Re: [la1k] LA-1K Trips to Standby in SSB

SWR is 1:1., using Palstar HF-auto tuner. Only noticed it on 20 meters. Does not trip to standby on other modes, on SSB I replaced jumper coax between IC-7610, LA-1K and HF-auto It's on voice peaks is

++++++++++++++++++++++1, then I could put the noisy “vacuum cleaner” in the corner of the room and wouldn’t be bothered by it too much ?. 73, Bernd – KB7AK Sent: Monday, August 15,

I had tripping issues. All I can tell you is Don’t drive the amp more than 45w. 50max and not more than 1000w output. 1. What is the SWR? 2. What band does it do it on? 3. Check your Coax ends

Thomas, 60-80 watts of drive is too much!!! The specs list 55W maximum. Palstar used to state 60W maximum but reduced it to 55W. You are going to damage your amp if you continue to drive it at

I do wish that my LA-1K had a CAT control so that from my PC I could put the LA-1K into STANDBY from OPERATE and then into OPERATE from STANDBY. As it stands now, to do the two commands, I have to

What band are you tripping out on? What is the SWR on the band? When you are using low power, what is the reflected power coming back? Are you using an antenna tuner? If using an antenna tuner, the

The LA-1K & HF-Auto make a nice pair. ?What transceiver are you going to use to excite them? Enjoy. Art W1SWL

I have also taken the plunge! Mine hasnt been powered up yet…working on my antenna, but I’m like a kid waiting for Christmas! I can hardly wait to make my first dx contact with my LA-1K and

My LA-1K keeps tripping to stand-by when I drive it on SSB. On CW, RTTY or FM/AM, I can key the amp with 60-80 watts drive and get full 1200 watts carrier out, no issue. Keys/Unkeys/ no

10 days from order to shipment , that’s great ! I love my Palstar auto tuner and LA 1K but I had to send the Amp back to the factory .After a year and a half with no problems it started

Good Stuff Gene. I also love my amp. I didn’t at first, but there was an issue with my amp and I wasn’t aware of it. Was a bad Capacitor that eventually went and had to send it back. Shipping

My experience exactly... I have two LA-1Ks and an HF Auto.Wonderful.DennisN0SP On 8/15/2022 at 9:07 AM, "Gene" wrote:I am pleased as punch with my new LA-1K and HF-Auto. I hooked them up today and

I am pleased as *punch* with my new *LA-1K* and *HF-Auto*. I hooked them up today and gave them a quick run through, made a couple of contacts, am super happy with the results! I did a lot of prior

Prep work? Just clear off a space so you can hook that sucker up and play with it! It does a great job of frequency sensing, but if you have icom or yaesu they sell a cable so that amp switches when

A while back, I ordered the LA-1K.? It should be here soon to Christmas time. The LA will replace and my Dentron 160-10L and Ameriton, Model ARB-704 setup that can be used as a back up.? Don't

Ron, Yes, my fans change speeds.? Station is off now, but I recall 3 speeds which are repeatable and tied to the temperature readout.? There is some hysteresis - the fans slow down at a different

This may sound correct in theory, however, is not the case for me. With 20w drive & 400w out, Eg. On 20m swr 1.3:1 ft8 15 sec cycles for 5 mins = temp 40c On 15m swr 1.1 same mode and cycle =