开云体育

?

This will be a straight out of the box build guide any optional or suggestions can be linked to, but should not be in this main description.

Getting Started

What you will need (Required)

• UBITX
• Soldering Iron & Solder
• Wire cutters. strippers or knife
• 12VDC Power Supply

What you probably should have (Optional)

• Enclosure - Not 100% necessary, but most will like have one, see Ubitx Enclosures for more ideas
• Low SWR Antenna

?

Wiring Diagram

Main Board & Raduino Assembly

Mount 4 of the 1cm threaded standoffs to the bottom of the main board so they act as feet.

Use 4 of the 1cm standoffs to connect the LCD display to the header board.

The header board plugs into the main board.

Power

The three pin power post on the board is located in the left rear of the main board (while looking at the display) and is labeled P1.

The three wire connector with Red, Black Brown wires mounts here.

The chassis mount power plug and the 1N4007 Diode (black and silver on one end)

Wiring Instructions

TODO: Diagram + Picture

• Tin all the posts
• Cut wires to length, strip bare and tin
• Red & Brown (+)
• Black (-)
• The Diode is wired across the (-) and (+) posts with the silver end of the diode on the (+) post.

Antenna

The two pin antenna post on the board is located on the right rear of the main board and is labeled J2

The two wire connector with Brown and Black wires mounts here.

The BNC connector

Wiring Instructions

TODO: Diagram + Picture

• Tin all the posts
• Cut wires to length (AS SHORT AS POSSIBLE), strip bare and tin
• Brown - Center of BNC
• Black - Outer shell (?? name ??) wiring post

?

Audio Harness

The audio harness mount is located on the front right of the main board and is labeled Audio1

To this you will mount one of the 8 wire multi-color harnesses and then connect the following components:

• Volume Knob
• 1/8" Speaker Jack
• 2 of the microphone wires (connected later)

Wiring Instructions

TODO: Diagram and Pictures

• Label the harness Audio
• Tin the three posts hanging off the bottom of the Volume knob & the 1/8" headphone jack
• Volume Knob
  • When looking at the display, the wires will be ordered left to right in this order: (You might actually have the board face down when you're soldering so double-check the order)
    • Green (Ground)
    • Yellow (Volume High)
    • Orange (Volume Mid)
• Headphone Jack
  • Black (Ground) - The single pin on the chassis side of the connector
  • Brown (Speaker +) - TODO... somewhere in this forum, there's a good explanation of this.

Raduino Harness

The Raduino harness mount is located on the top right of the header board holding the display and is labeled P1 on the front facing side of the board.

To this you will mount one of the 8 wire multi-color harnesses and then connect the following components:

• Tuning Knob
• 1/8" Jack for Key
• 1/8" Jack for Microphone (2 wires from the audio + 1 from the Raduino)

Wiring Instructions

TODO: Diagram and Pictures

• Tin the 5 posts on the tuning knob, and the posts on the 1/8" jacks
• Tuning Knob will be wired so that when looking at the display and down onto the knob, the wires will be in following order left to right:
  • Top three wires:?
    • Brown (ENC_B)
    • Yellow (Ground)
    • Black (ENC_A)
  • Bottom two wires:
    • Red (F_BTN)
    • Yellow (Ground)
• Microphone
  • TODO: I didn't use the included microphone setup, I need help with this.
• Key
  • TODO: I only put in the Resister and not the jack, I need help with this.

?