Keyboard Shortcuts
Likes
- Winfldigi
- Messages
Search
|
Re: IC7300 CW with FlDigi 4.2.06
Anders Georgsson
When in doubt - restart ?? IT rule #2 ?? Yes - i've tried that as well. On Tue, Mar 18, 2025 at 12:32?PM Jean Christophe Barbera via <jc-barbera=[email protected]> wrote:
--
Anders Georgsson (352)316-0258 cell? KZ4JN/WSDF851 |
|
Re: IC7300 CW with FlDigi 4.2.06
开云体育I'm new to this software. I sometimes have difficulties. I've noticed that it's sometimes necessary to close the software for changes to take effect. Jean-Christophe BARB?RA Le 18 mars 2025 à 16:12, Anders Georgsson via groups.io <anders.georgsson@...> a écrit?:
|
|
Re: IC7300 CW with FlDigi 4.2.06
Anders Georgsson
Hmm - did have <# TXRSID:on> in my macro (which should mean that it isn't executed, right?) but I removed that line all together and it is still behaving this way.
The only button I have turned on at the top right in FlDigi is "Spot"...
?
I even tried turning that off but it still toggling the between TX/RX during the transmission of code...
?
I am not sure if I mentioned this in my original post but I'm using FLRIG to control my rig (so I can control it remotely) - if I use it's CW Keyer - the radio pulses the signal rather than keeping the transmitter on and playing the tone thru the integrated sound card as well?
?
? |
|
Re: TenTec Jupiter FLRig config - help
Ron,
I have tried with my Jupiter (green screen) several times. No joy.? I have been successful when I select Pegasus mode. It works but of course you can only control from flrig.??
?
I didn't like that mode as I found it cumbersome to just scroll the band to listen to whomever was on.
?
73
Bill
W1WRH? |
|
Re: LK on at startup
Don't get me going Bob on being inconvenienced, lazy, or pressed for time.? Neither is the case here. I'm working on a station automation project with NodeRed and Stream Deck. The LK button is one thing I am trying to get figured out.?
?
I'm looking for help here, not snark.
?
-Randy |
|
Re: IC7300 CW with FlDigi 4.2.06
开云体育Check if the macros have TXID. If so, TXID ?and rxid must be enabled.F5ind 73 Chris? Jean-Christophe BARB?RA Le 18 mars 2025 à 01:54, Anders Georgsson via groups.io <anders.georgsson@...> a écrit?:
|
|
IC7300 CW with FlDigi 4.2.06
Anders Georgsson
I had it working fairly well but now, suddenly - something has happened so as my IC7300 is transmitting the tone, the radio releases the PTT , pauses and reengages the PTT and continues!?
?
I read and followed the instructions for using FLRIG and FLDIGI together but it's just not working like it used to.
?
It used to trigger the transmitter and FlDigi would pulse its tones and once finished - it'd switch back to receive mode.. I don't believe I used to have to enable break-in or full break-in..
If I don't do that now - then I can HEAR the tone but it is never transmitted. Any suggestions? |
|
Re: LK on at startup
I tried selecting LK and then SAVE CONFIG. Exited the program and then reloaded the program. LK was not restored.
I was reading on another site where the operator found that pushing a button was too much inconvenience. ?????? Are we getting lazy or are we pressed for time? 73 Bob, K4TAX |
|
TenTec Jupiter FLRig config - help
Hi all,
???? I am trying to connect my Jupiter to FLRig v2.0.05 on Win11.? The connection is USB.? I know the connection works.? I have used it successfully with Winlink RMS Trimode.? I tried the 'standard' config that comes up when I click on TT-538.? All baud is 57600.
1 Stop bit
RTS/CTS on
RTS +12v on
DTR +12 v off
I tried the connection that works in Trimode
RTS on
DTR on
???? Has anyone gotten their Jupiter to connect with this USB connection?? Thanks
--
73,
???? Rory Griffin W4RJG |
|
Re: LK on at startup
Not sure, but if you set it on, then go to configure, then drop down to save config.? ?it may save for next startup Dave Garber VE3WEJ / VE3IE On Sun, Mar 16, 2025 at 11:14?AM Randy Buxton, W4IFI via <randybuxton=[email protected]> wrote:
|
|
LK on at startup
I want the LK button to be ON when I start up Fldigi. I know that a script can accomplish this task. I don't want to push the buttons to execute the script. I want the LK button ON every time I start Fldigi without having to push any other buttons.?
?
Can this be done? If so, how?
?
Thanks.
?
-Randy, W4IFI
? |
|
Re: No modulation rtty but decode ok.
开云体育Hi Chris, Sorry, I must have missed the email that said about your successes with the other programs.... I hope that you find the answer.... Best 73 and good DX. de WA3ZSC - Jerry
On 03-13-2025 18:23:03, Jean Christophe
Barbera via groups.io wrote:
Jerry This configuration (icom7700 and interface rigexpert) works perfectly with three other software programs (logger32/n1mm and 2tone/ and mmtty). This would make me think more of a problem between FLDIGI and the RIGEXPERTti5000 interface. Do you think the ports would only be default with FLDIGI, and not with the others? 73 chris Jean-Christophe BARB?RALe 13 mars 2025 à 20:43, gksmith_1 via groups.io <gksmith_1@...> a écrit : OK. Sorry about that.... have you checked to make sure that Windows has not powered down your USB ports? Check in Control Panel, Power Options. Make sure that the computer is not shutting down anything to save power, and make sure that nothing is going into Hibernation or Sleep.... all these things seem to be a problem. Also check in Device manager, check every USB device, Hubs included, and make sure that Windows cannot shut down the USB devices to save power. Actually, check everything in Device Manager, even if it seems unrelated. Also, make sure that the computer is not set to shut down any of your displays. HDMI audio for your display, going to sleep also causes problems. |
|
Re: No modulation rtty but decode ok.
Jerry
toggle quoted message
Show quoted text
This configuration (icom7700 and interface rigexpert) works perfectly with three other software programs (logger32/n1mm and 2tone/ and mmtty). This would make me think more of a problem between FLDIGI and the RIGEXPERTti5000 interface. Do you think the ports would only be default with FLDIGI, and not with the others? 73 chris Jean-Christophe BARB?RA Le 13 mars 2025 à 20:43, gksmith_1 via groups.io <gksmith_1@...> a écrit : |
|
Re: No modulation rtty but decode ok.
开云体育Hi Chris,
OK. Sorry about that.... have you
checked to make sure that Windows has not powered down your USB
ports?
Check in Control Panel, Power Options.
Make sure that the computer is not shutting down anything to save
power, and make sure that nothing is going into Hibernation or
Sleep....? all these things seem to be a problem.
Also check in Device manager, check
every USB device, Hubs included, and make sure that Windows cannot
shut down the USB devices to save power.
Actually, check everything in Device
Manager, even if it seems unrelated.
Also, make sure that the computer is
not set to shut down any of your displays. HDMI audio for your
display, going to sleep also causes problems.
?
Best of luck.
73 de WA3ZSC- Jerry
?Jean Christophe Barbera via groups.io
wrote:
|
|
Re: No modulation rtty but decode ok.
开云体育Hey Jerry, No, it doesn't work. Thanks for your help anyway. 73 f5ind ?Chris? Jean-Christophe BARB?RA Le 13 mars 2025 à 13:12, gksmith_1 via groups.io <gksmith_1@...> a écrit?:
|
|
Re: No modulation rtty but decode ok.
开云体育Okay Jerry. I understand the procedure. I didn't think so. I'll try it and give you feedback. Because I can't think of any further research. I think I've covered all the important points. Sound card, sound settings, up-to-date driver, and the various settings in the software. 73 chris f5ind. Jean-Christophe BARB?RA Le 13 mars 2025 à 13:12, gksmith_1 via groups.io <gksmith_1@...> a écrit?:
|
|
Re: No modulation rtty but decode ok.
开云体育Hi Chris, I am not a developer, but I will give you a possibility. I am not familiar with your interface, but if you are running FSK for RTTY, then there is a chance that your FSK port has gotten corrupted with its association with Windows. I have had this same problem, but with a different interface. While I do not use Fldigi for RTTY, I use N1MM Logger, my solution is to 1) Shut down the RTTY program, in your case
Fldigi 2) Go into Device Manager and find your FSK port 3) Uninstall your FSK port, BUT do NOT delete the driver 4) Click OK to confirm that you want to uninstall the FSK port. 5) Go to the top of the Device Manager and click on Action 6) Click on Scan for hardware changes. The computer should find your FSK port automatically and re-install it. In my case this solved the problem. With practice, you should be able to do this in less than a minute when the problem occurs. 73 de WA3ZSC - Jerry
On 03-12-2025 05:53:06, Jean Christophe
Barbera via groups.io wrote:
|
|
No modulation rtty but decode ok.
开云体育Setup:? Icom ic7700. Interface rigexpert TI5000. hello. it only outputs tone and power, without shift. I am on the settings of another device. the macros are functional with another station. the rigexpert TI5000 interface creates 4 ports. (fsk/ptt/cat/cw). the sound card is identified, I tried the 3 possibilities. I tried the cat with hamlib and rigcat. fsk modem I give it the fsk port. Anyone have any idea?? 73 f5ind chris Jean-Christophe BARB?RA |
|
Re: <MAPIT> MACRO
#fldigi-parameters
开云体育Thanks John. Hey long time to talk to. I am getting set up for the St. Pat's day sprint. Hope to work you again. Take care Dave On 3/10/2025 4:06 PM, John KC3FL via
groups.io wrote:
-- 73's de NU4N -- 73'S DAVE NU4N |
Bob McGraw - K4TAX
Rory Griffin, W4RJG