Re: FLRig Power Out Issue (FT-2000)
I have the attachments and will look?into it.
David On Fri, May 9, 2025 at 8:58?AM Daniel V. Wolff, Jr. (KA7AGN / DL4VCW / AEM1WF, Ret.) via <vegiewolff= [email protected]> wrote:
Reference: -????????? FLRig 2.0.05.85 -????????? Fldigi 4.2.06.16 -????????? Yaesu FT-2000 ? ? Greetings, Dave. ? ? I discovered a new problem.? The output power is reduced on the transceiver when FLRig is initialized. I uploaded a video for you.? You¡¯ll have to download it because it¡¯s too large to attach to the email. The video explains the issue hopefully better. ?
? I also attached the TRACE files for your review.? I think the TRACE files will tell a better story.? ? Power shows 253 when transceiver is adjusted to 100 watts.? But, 253 is still not full power out. ? ? 
? Then, sliding the power adjustment down and back up to max, goes to 100. Never goes back to 253. ? 
? ? ? 73, ? DANIEL V. WOLFF, JR. DL4VCW, KA7AGN, AEM1WF (Ret.)
? ? --
73,?
DANIEL V. WOLFF, JR.
DL4VCW / KA7AGN / AEM1WF (Ret.)
?
|
Unable to transmit with Yaesu FT-991
I have been trying to get FLDIGI to transmit all week and decided to troubleshoot a bit. I recently got a small laptop with Windows 11, did the FLDIGI and FLRIG install and had it working right away. I am able to decode and transmit perfectly on it because I just had my first QSO, so I know it's not my radio settings. There is something in my Windows 10 computer that isn't allowing me to transmit and I can't figure it out. The settings on both computers are equal as far as I know.
?
My speaker volume is set at 100%
Mic volume is adjusted as needed to keep the green monitor at the bottom of the screen at -20.
Numbers next to the waterfall button are 0 and 60.
My rig is connected with a USB cord for control.
I am working in DATA-U mode
?
Any ideas?
|
If you feel there is a specific ?topic you would like to learn or review, please email me some specifics
at
?
I will have a general slide show (PDF or PowerPoint) at the start going over the CONFIGURATION setup for a variety of rigs.
?
Please first consult the very well written HELP GUIDE on Fldigi.
It has a wealth of information.
?
de k3eui?
barry
Philly
?
?
|
Re: Anyone able to get ICOM IC-707 Transmit working?
Ok, I'll look into the vox approach.
But here was my thinking with trying to get fldigi to work "natively", since I can indeed get fldigi to trigger the transceiver?to transmit by manually toggling the?Hamlib "RTS/CTS flow control" and "RTS +12" settings, then I know that fldigi is able to "talk to" the transceiver?and get it to transmit. The only problem with manually toggling?the Hamlib "RTS/CTS flow control" and "RTS +12" settings is that the transceiver?stays transmitting until I uncheck the settings.
So, I'm thinking that some sort of fldigi configuration may still be a possible solution...I'm just?don't have enough fldigi debug experience to figure it out.
BTW, is there anyone out there that DOES have deep fldigi debug experience that would be willing to help me on this over a call or video meeting? I would be happy to pay an hourly rate for anyone's time on this...perhaps venmo...if anyone is interested, let me know.
Thanks,
John
does the digirig have vox setting like the signalink??? i dont know, if not , then perhaps putting the radio in vox on mode, and ptt via rts? maybe
Dave Garber VE3WEJ / VE3IE
On Thu, May 8, 2025 at 10:50?AM John Tumminaro via <johntumminaro= [email protected]> wrote: I am using Digirig?Mobile as my PC-to-Rig interface
RE "perhaps you need to use the vox method", what would that mean from an fldigi configuration perspective?
Thanks,
John
what are you using for sound card interface?? perhaps you need to use the vox method, and not cat ptt
Dave Garber VE3WEJ / VE3IE
On Wed, May 7, 2025 at 7:49?PM johntumminaro via <johntumminaro= [email protected]> wrote: I am using Fldigi 4.2.06.
I have Rig Control set for "Use Hamlib".
For the Hamlib "Rig" setting I have "Icom IC-707 (Alpha)" selected.
Other then the Hamlib "Device" and "Baud rate" settings, all other Hamlib settings are set to default.
Screenshot of Hamlib settings attached.
?
My issue is that I am unable to get fldigi to trigger the transceiver to actually transmit when transmitting in fldigi.
?
Note that if I check the Hamlib "RTS/CTS flow control" setting then it DOES trigger the transceiver to actually transmit but is then stuck in transmit mode.
Note that if I check the Hamlib "RTS +12" setting then it DOES trigger the transceiver to actually transmit but is then stuck in transmit mode.
Note that fldigi DOES display the correct frequency from the transceiver and DOES update it when changed on the transceiver.
Note that fldigi DOES display the correct mode from the transceiver and DOES update it when changed on the transceiver.
?
Any guidance/thoughts appreciated.
?
John
?
|
FLRig Power Out Issue (FT-2000)
Reference: -????????? FLRig 2.0.05.85 -????????? Fldigi 4.2.06.16 -????????? Yaesu FT-2000 ? ? Greetings, Dave. ? ? I discovered a new problem.? The output power is reduced on the transceiver when FLRig is initialized. I uploaded a video for you.? You¡¯ll have to download it because it¡¯s too large to attach to the email. The video explains the issue hopefully better. ? ? I also attached the TRACE files for your review.? I think the TRACE files will tell a better story.? ? Power shows 253 when transceiver is adjusted to 100 watts.? But, 253 is still not full power out. ? ? 
? Then, sliding the power adjustment down and back up to max, goes to 100. Never goes back to 253. ? 
? ? ? 73, ? DANIEL V. WOLFF, JR. DL4VCW, KA7AGN, AEM1WF (Ret.)
? ? --
73,?
DANIEL V. WOLFF, JR.
DL4VCW / KA7AGN / AEM1WF (Ret.)
?
|
Thank you this will be of great help to me! Mary KK7IMG?
toggle quoted message
Show quoted text
On May 8, 2025, at 5:49?AM, Fred.kantzer via groups.io <Fred.kantzer@...> wrote:
? I'm adding this to my calendar.?
?
Fred, KE8WSM
|
Setting 991a menu for data.
Data-usb ou data-Lsb : usb port or data cinch. S¨¦lect your choice.
Jean-Christophe BARB?RA
toggle quoted message
Show quoted text
Le 8 mai 2025 ¨¤ 15:46, Charles Hargrove via groups.io <n2nov@...> a ¨¦crit :
?USB = upper sideband for voice/microphone input
DATA-U = upper sideband but using data input instead of microphone
On 5/8/2025 9:41 AM, n8vlc via groups.io wrote:
I applied your recommendations and was able to see a perfectly decoded message this morning. I had been told that I MUST keep my mode in USB for everything, but I had better luck today switching it to DATA-U. I also turned up my mic so the green monitor was right around -20 --
Charles J. Hargrove - N2NOV
NYC-ARECS/RACES Citywide Radio Officer/Skywarn Coord.
NYC-ARECS/RACES Nets 441.100/136.5 PL
ARnewsline Broadcast Mon. @ 8:00PM
NYC-ARECS Weekly Net Mon. @ 8:30PM
NY-NBEMS Net Saturdays @ 10AM & USeast-NBEMS Net Wednesdays @ 7PM
on 7.036 Mhz USB (alt 3.536)/1500 hz waterfall spot; MFSK-16 or 32
"Information is the oxygen of the modern age. It seeps through the walls topped
by barbed wire, it wafts across the electrified borders." - Ronald Reagan
"The more corrupt the state, the more it legislates." - Tacitus
"Molann an obair an fear" - Irish Saying
(The work praises the man.)
"No matter how big and powerful government gets, and the many services it
provides, it can never take the place of volunteers." - Ronald Reagan
|
Re: Anyone able to get ICOM IC-707 Transmit working?
does the digirig have vox setting like the signalink??? i dont know, if not , then perhaps putting the radio in vox on mode, and ptt via rts? maybe
Dave Garber VE3WEJ / VE3IE
On Thu, May 8, 2025 at 10:50?AM John Tumminaro via <johntumminaro= [email protected]> wrote: I am using Digirig?Mobile as my PC-to-Rig interface
RE "perhaps you need to use the vox method", what would that mean from an fldigi configuration perspective?
Thanks,
John
what are you using for sound card interface?? perhaps you need to use the vox method, and not cat ptt
Dave Garber VE3WEJ / VE3IE
On Wed, May 7, 2025 at 7:49?PM johntumminaro via <johntumminaro= [email protected]> wrote: I am using Fldigi 4.2.06.
I have Rig Control set for "Use Hamlib".
For the Hamlib "Rig" setting I have "Icom IC-707 (Alpha)" selected.
Other then the Hamlib "Device" and "Baud rate" settings, all other Hamlib settings are set to default.
Screenshot of Hamlib settings attached.
?
My issue is that I am unable to get fldigi to trigger the transceiver to actually transmit when transmitting in fldigi.
?
Note that if I check the Hamlib "RTS/CTS flow control" setting then it DOES trigger the transceiver to actually transmit but is then stuck in transmit mode.
Note that if I check the Hamlib "RTS +12" setting then it DOES trigger the transceiver to actually transmit but is then stuck in transmit mode.
Note that fldigi DOES display the correct frequency from the transceiver and DOES update it when changed on the transceiver.
Note that fldigi DOES display the correct mode from the transceiver and DOES update it when changed on the transceiver.
?
Any guidance/thoughts appreciated.
?
John
?
|
Re: flrig & the user interface
Also in FLdigi there is the under the Misc the Autostart.
There I can input all the FL Programs to come up when I start FLdigi.
Just things we are finding out with this amazing program.
?
|
Re: flrig & the user interface
On flrig on the config button under the UI there is the user interface button.
I clicket on it to see what it did.
On my IC-7100 there is the same interface but when you click any button it goes away.
That is why I want to know if there is is a way to get the user interface to come up.
|
Re: flamp versions on w1hkj.org vs. sourceforge.net
|
Re: flrig & the user interface
So, when you open FLRIG, you have no user interface? How do you even know it's open then?
|
Re: Anyone able to get ICOM IC-707 Transmit working?
I am using Digirig?Mobile as my PC-to-Rig interface
RE "perhaps you need to use the vox method", what would that mean from an fldigi configuration perspective?
Thanks,
John
what are you using for sound card interface?? perhaps you need to use the vox method, and not cat ptt
Dave Garber VE3WEJ / VE3IE
On Wed, May 7, 2025 at 7:49?PM johntumminaro via <johntumminaro= [email protected]> wrote: I am using Fldigi 4.2.06.
I have Rig Control set for "Use Hamlib".
For the Hamlib "Rig" setting I have "Icom IC-707 (Alpha)" selected.
Other then the Hamlib "Device" and "Baud rate" settings, all other Hamlib settings are set to default.
Screenshot of Hamlib settings attached.
?
My issue is that I am unable to get fldigi to trigger the transceiver to actually transmit when transmitting in fldigi.
?
Note that if I check the Hamlib "RTS/CTS flow control" setting then it DOES trigger the transceiver to actually transmit but is then stuck in transmit mode.
Note that if I check the Hamlib "RTS +12" setting then it DOES trigger the transceiver to actually transmit but is then stuck in transmit mode.
Note that fldigi DOES display the correct frequency from the transceiver and DOES update it when changed on the transceiver.
Note that fldigi DOES display the correct mode from the transceiver and DOES update it when changed on the transceiver.
?
Any guidance/thoughts appreciated.
?
John
?
|
Hi Barry,
My name is Randy / n7wwa. I used to participate in the PA nbems digi nets several years ago. At that time, there was a guy out of Pittsburgh that was NCS most of the time. I am in WV at Point Pleasant. I am in NVIS range of most of OH and Western PA and all of WV? I am pretty well versed in most all digi modes but would like to join your zoom meeting and start checking onto your nets and contribute as needed
73 de n7wwa
Sent from ProtonMail, encrypted email based in Switzerland.
Sent from Proton Mail Android
-------- Original Message -------- On 5/8/25 07:24, K3EUI Barry via groups.io wrote: A few of us in the Philly region are starting a new net: ?FLDIGI TRAINING NET
This may be helpful especially for rookies with FLDIGI.
?
Net time: ?1st and 3rd Saturday of each month: ?9:00 AM Eastern
Zoom link to begin the net:
https://us02web.zoom.us/j/7950991313?pwd=NFVJN1lQaDVlZUZQNGFnYTRiR0orQT09
?
?
We will use 3583 kHz and 7068 kHz (vfo dial) @1500 Hz on waterfall for practice if the frequency is open.
?
I¡¯m hoping we can help each other with problems.
?
?
?
|
USB = upper sideband for voice/microphone input
DATA-U = upper sideband but using data input instead of microphone
toggle quoted message
Show quoted text
On 5/8/2025 9:41 AM, n8vlc via groups.io wrote: I applied your recommendations and was able to see a perfectly decoded message this morning. I had been told that I MUST keep my mode in USB for everything, but I had better luck today switching it to DATA-U. I also turned up my mic so the green monitor was right around -20
--
Charles J. Hargrove - N2NOV
NYC-ARECS/RACES Citywide Radio Officer/Skywarn Coord.
NYC-ARECS/RACES Nets 441.100/136.5 PL
ARnewsline Broadcast Mon. @ 8:00PM
NYC-ARECS Weekly Net Mon. @ 8:30PM
NY-NBEMS Net Saturdays @ 10AM & USeast-NBEMS Net Wednesdays @ 7PM
on 7.036 Mhz USB (alt 3.536)/1500 hz waterfall spot; MFSK-16 or 32
"Information is the oxygen of the modern age. It seeps through the walls topped
by barbed wire, it wafts across the electrified borders." - Ronald Reagan
"The more corrupt the state, the more it legislates." - Tacitus
"Molann an obair an fear" - Irish Saying
(The work praises the man.)
"No matter how big and powerful government gets, and the many services it
provides, it can never take the place of volunteers." - Ronald Reagan
|
|
|
Thanks for the reply, Barry!
?
I applied your recommendations and was able to see a perfectly decoded message this morning. I had been told that I MUST keep my mode in USB for everything, but I had better luck today switching it to DATA-U. I also turned up my mic so the green monitor was right around -20.
?
A friend and I tried to communicate back and forth last night and I could see him, but only half was decoded. He was unable to see my transmission at all. I don't know if it was on my end or his. I can only assume at this time that I'm doing it correctly. When I send my message, it starts typing in red in the top screen and the waterfall shows a bright yellow streak.
?
In the left screen where the frequencies pop up, I saw a CQ in red and clicked on it. It came through perfect. At the moment, there doesn't seem to be any activity.?Can I assume if I click on a signal in the waterfall, it should do the same as clicking in the list on the left of the screen and take me to that transmission?
?
Thanks for your help!
|
Re: Anyone able to get ICOM IC-707 Transmit working?
what are you using for sound card interface?? perhaps you need to use the vox method, and not cat ptt
Dave Garber VE3WEJ / VE3IE
On Wed, May 7, 2025 at 7:49?PM johntumminaro via <johntumminaro= [email protected]> wrote: I am using Fldigi 4.2.06.
I have Rig Control set for "Use Hamlib".
For the Hamlib "Rig" setting I have "Icom IC-707 (Alpha)" selected.
Other then the Hamlib "Device" and "Baud rate" settings, all other Hamlib settings are set to default.
Screenshot of Hamlib settings attached.
?
My issue is that I am unable to get fldigi to trigger the transceiver to actually transmit when transmitting in fldigi.
?
Note that if I check the Hamlib "RTS/CTS flow control" setting then it DOES trigger the transceiver to actually transmit but is then stuck in transmit mode.
Note that if I check the Hamlib "RTS +12" setting then it DOES trigger the transceiver to actually transmit but is then stuck in transmit mode.
Note that fldigi DOES display the correct frequency from the transceiver and DOES update it when changed on the transceiver.
Note that fldigi DOES display the correct mode from the transceiver and DOES update it when changed on the transceiver.
?
Any guidance/thoughts appreciated.
?
John
?
|
I'm adding this to my calendar.?
?
Fred, KE8WSM
|
Re: flamp versions on w1hkj.org vs. sourceforge.net
Thank you Dan.? Simply an oversight on my part (and the result of changes in my personal life).? Sorge Forge has been updated.
David
On Thu, May 8, 2025 at 6:35?AM Dan N3YQ Maryland via <dpwilt= [email protected]> wrote: Hi all,
?
I wanted to check my Windows versions of fldigi, flmsg, flamp, and flrig were current, and found that and have different versions of flamp - 2.2.13 on sourceforge, and 2.2.14 on w1hkj.? I noted the difference a while ago (a month or so), and figured it was just a lag between the two sites.? Is it a (minor) oversight, or is being deprecated?
?
Thanks for all you do!? Fldigi rocks!!
?
73, Dan N3YQ
|
Dave
K3EUI Barry
John Tumminaro
Daniel V. Wolff, Jr. (KA7AGN / DL4VCW / AEM1WF, Ret.)
Dan N3YQ Maryland
Drew