Re: Anyone out there using an FT-950? Do you mind sharing your FLRig / FLdigi settings?
Doug,
?
I use the 950, however I do not use flrig, I use rigcat and have used hamlib in the past.? I still might be able to help you, so shoot me an email, good on QRZ.com.
?
73
John
KC3FL
|
Looks like did not like my PowerPoint attachment.
It can be?found at:
For hamplib config specific to IC-7100:
- select IC-7100 as rig
- com port as presented to PC
- 19200 baud
I was unsuccessful with using autobaud on the IC-7100 but that may have been user error.
I am successfully using FLDIGI itg an IC-7100.
The IC-7100 setting I am using are as shwn?in:
The FLDIGI settings are per the attached documentl
On Sun, Oct 13, 2024 at 10:57?PM mike isakson via <w7xh.mike= [email protected]> wrote: thanks Phil, but I must say that I had flrig connected to fldigi and fldigi connected to n3fjp. All operating together perfectly with the IC-7100. Flrig would set the band on all software and fldigi would parse the contact information. The problem was that I was using the rtty settings on the radio. My radio uses fsk and so I had a constant tone rather than the rtty diddle. I believe that David? or someone here in the group suggested that I use usb-d. That seemed to work . Unfortunately, trying so many things and not keeping a good record , I kept breaking my efforts. It would be great if an IC-7100 owner could provide their settings, understanding that it has it's own sound card and control is via a usb cable.
I am thankful for the group response and their information. It would be good for some updated data based on fldigi 4.2.xx and flrig 2.2.xx. Many of the screen shots are from much earlier versions.
On Sat, Oct 12, 2024 at 9:45?PM Philip - K4PO via <K4PO.ARS= [email protected]> wrote: Mike,
Either FLDigi or N3FJP logger can control the but only one can be connected at a time.? Best to let FLDigi do the CAT work and make log entries.? Same if you run WSJTx where you marry WSJTx to Jtalert then let Jtalert do the logging.
Phil / K4PO
?
?
--
|
I am successfully using FLDIGI itg an IC-7100.
The IC-7100 setting I am using are as shwn?in:
The FLDIGI settings are per the attached documentl
On Sun, Oct 13, 2024 at 10:57?PM mike isakson via <w7xh.mike= [email protected]> wrote: thanks Phil, but I must say that I had flrig connected to fldigi and fldigi connected to n3fjp. All operating together perfectly with the IC-7100. Flrig would set the band on all software and fldigi would parse the contact information. The problem was that I was using the rtty settings on the radio. My radio uses fsk and so I had a constant tone rather than the rtty diddle. I believe that David? or someone here in the group suggested that I use usb-d. That seemed to work . Unfortunately, trying so many things and not keeping a good record , I kept breaking my efforts. It would be great if an IC-7100 owner could provide their settings, understanding that it has it's own sound card and control is via a usb cable.
I am thankful for the group response and their information. It would be good for some updated data based on fldigi 4.2.xx and flrig 2.2.xx. Many of the screen shots are from much earlier versions.
On Sat, Oct 12, 2024 at 9:45?PM Philip - K4PO via <K4PO.ARS= [email protected]> wrote: Mike,
Either FLDigi or N3FJP logger can control the but only one can be connected at a time.? Best to let FLDigi do the CAT work and make log entries.? Same if you run WSJTx where you marry WSJTx to Jtalert then let Jtalert do the logging.
Phil / K4PO
?
?
|
#1 Set up a virtual com port pair -- com0com or Eltima (assuming Windows)? -- let's pretend you set up COM5/COM6
#2 Set up FLRig to talk to your rig
#3 Set WSJT-X to use FLRig?
#4 Run rigctlcom
rigctlcom -m 4 -R com5 -S 115200
#5 Set N3FJP so use COM6/115200 as a TS-2000
Mike W9MDB
toggle quoted message
Show quoted text
On Sunday, October 13, 2024 at 10:04:10 PM CDT, mike isakson <w7xh.mike@...> wrote: I could use a little more explaination. On Sat, Oct 12, 2024 at 9:50?PM Mike Black via groups.io <mdblack98@...> wrote: Actually you can do this:
FLDigi -> FLRig
N3FJP -> Hamlib rigctlcom -> FLRig
WSJTX -> FLRig (via Hamlib)
rigctlcom is the magic glue that emulates a TS-2000 and can connect most any program (other than Ham Radio Deluxe) to FLRig or any other rig for that matter via a virtual serial port.
Mike W9MDB
On Saturday, October 12, 2024 at 11:45:34 PM CDT, Philip - K4PO <k4po.ars@...> wrote:
Mike,
Either FLDigi or N3FJP logger can control the but only one can be connected at a time.? Best to let FLDigi do the CAT work and make log entries.? Same if you run WSJTx where you marry WSJTx to Jtalert then let Jtalert do the logging.
Phil / K4PO
?
?
|
I could use a little more explaination.
Actually you can do this:
FLDigi -> FLRig
N3FJP -> Hamlib rigctlcom -> FLRig
WSJTX -> FLRig (via Hamlib)
rigctlcom is the magic glue that emulates a TS-2000 and can connect most any program (other than Ham Radio Deluxe) to FLRig or any other rig for that matter via a virtual serial port.
Mike W9MDB
On Saturday, October 12, 2024 at 11:45:34 PM CDT, Philip - K4PO <k4po.ars@...> wrote:
Mike,
Either FLDigi or N3FJP logger can control the but only one can be connected at a time.? Best to let FLDigi do the CAT work and make log entries.? Same if you run WSJTx where you marry WSJTx to Jtalert then let Jtalert do the logging.
Phil / K4PO
?
?
|
thanks Phil, but I must say that I had flrig connected to fldigi and fldigi connected to n3fjp. All operating together perfectly with the IC-7100. Flrig would set the band on all software and fldigi would parse the contact information. The problem was that I was using the rtty settings on the radio. My radio uses fsk and so I had a constant tone rather than the rtty diddle. I believe that David? or someone here in the group suggested that I use usb-d. That seemed to work . Unfortunately, trying so many things and not keeping a good record , I kept breaking my efforts. It would be great if an IC-7100 owner could provide their settings, understanding that it has it's own sound card and control is via a usb cable.
I am thankful for the group response and their information. It would be good for some updated data based on fldigi 4.2.xx and flrig 2.2.xx. Many of the screen shots are from much earlier versions.
On Sat, Oct 12, 2024 at 9:45?PM Philip - K4PO via <K4PO.ARS= [email protected]> wrote: Mike,
Either FLDigi or N3FJP logger can control the but only one can be connected at a time.? Best to let FLDigi do the CAT work and make log entries.? Same if you run WSJTx where you marry WSJTx to Jtalert then let Jtalert do the logging.
Phil / K4PO
?
?
|
Anyone out there using an FT-950? Do you mind sharing your FLRig / FLdigi settings?
I am STRUGGLING to get fldigi and flrig to work. Currently opening FLRig activates the PTT on the transceiver and the only way to stop it is to restart the transceiver. From there I can adjust things through FLRig and I see the same things change on the transciever, so I know serial is talking fine.
?
Once I get into FLdigi and try to transmit anything I notice the PTT never kicks on, so the transceiver doesn't actually send anything out.
?
I'm using Win 11 64bit, I'll be happy to provide further info but I'm not sure what else is relevant to include here.
?
Thanks!
AF5EI
-Doug
|
Re: TS-2000 Kenwood problem, PLEASE HELP
Yes, This was covered here on the group recently on msg ? Mar 23???#36250????
73
?
vk4tux
|
Re: TS-2000 Kenwood problem, PLEASE HELP
And preferably the ACC2 adapter is connected to pin 9 and not pin 13 so that the mic gets muted.
Otherwise you have to turn down the mic gain to ensure you don't mix room noise with your signal.
Mike W9MDB
toggle quoted message
Show quoted text
On Sunday, October 13, 2024 at 09:23:28 AM CDT, Adrian Fewster <vk4tux@...> wrote: I agree, and have seen this happen before, cat ptt will enable the front audio path rather than the rear ACC audio path activated by vox. In wsjtx? vox was probably selected for ptt, hence why it worked. Signallink does the vox ptt switching without cat or comport input. 73 vk4tux On 13/10/24 23:52, gqwradio via groups.io wrote: ?? Ben: Ensure that in the FLrig set up, PTT by CAT is NOT selected. PTT by CAT takes precedence over any other PTT selections and CAT PTT will cause the 2000 to use mic and spkr for audio instead of audio to/from the 13 pin AUX connector. I hope that fixes your problem! 73 de Bob?? VE3YX On 2024-10-13 07:20, Herr K wrote: ?? Hello everybody! I'm struggling with my TS2000 along with a SignaLink SL-1+ to work with FLDIGI. First of all: I'm using this setup succesfully for a long time now with WSJT-X. My notebook is connected via USB to the TS2000 and via 3,5mm Headphone-Jack to the SignaLink. The SignaLink is connected to the TS2000 via the 13-ACC-Connector. ? Now to FLDigi: In order to make the connection between the TS2000 and my notebook I'm using FLRig. So far so good. This is my problem: My notebook (FLDigi) is hearing the signals but only through the microphone of my notebook. If I turn down the volume of the TS2000 no signals are being decoded.... Sending is about the same problem: If I hit the tune-button of FLDigi the TS2000 switches to transmit but the SignaLink doesn't switch to "PTT" and the TS2000 expects audio from the microphon.... I've tried so many settings but all in vain.... It's driving me nuts. Does anyone have a solution how to setup TS2000 along with the SignaLink SL-1+ to work with FLDigi? PLEASE HELP! ? VY73 de Ben (DL4DBM)
|
Re: TS-2000 Kenwood problem, PLEASE HELP
I think I've got the setup running now! THANKS TO ALL OF YOU! I'll give it a try tomorrow whenn the contest is over :-) It'll be my very first contact with FLDigi....
I'll let you know!
?
73 de Ben (DL4DBM)
|
Re: TS-2000 Kenwood problem, PLEASE HELP
Ben:
Ensure that in the FLrig set up, PTT by CAT is NOT selected. PTT
by CAT takes precedence over any other PTT selections and CAT PTT
will cause the 2000 to use mic and spkr for audio instead of audio
to/from the 13 pin AUX connector.
I hope that fixes your problem!
73 de Bob?? VE3YX
On 2024-10-13 07:20, Herr K wrote:
toggle quoted message
Show quoted text
Hello everybody!
I'm struggling with my TS2000 along with a SignaLink SL-1+ to
work with FLDIGI.
First of all: I'm using this setup succesfully for a long
time now with WSJT-X.
My notebook is connected via USB to the TS2000 and via 3,5mm
Headphone-Jack to the SignaLink. The SignaLink is connected to
the TS2000 via the 13-ACC-Connector.
?
Now to FLDigi:
In order to make the connection between the TS2000 and my
notebook I'm using FLRig. So far so good.
This is my problem:
My notebook (FLDigi) is hearing the signals but only through
the microphone of my notebook. If I turn down the volume of the
TS2000 no signals are being decoded....
Sending is about the same problem: If I hit the tune-button
of FLDigi the TS2000 switches to transmit but the SignaLink
doesn't switch to "PTT" and the TS2000 expects audio from the
microphon....
I've tried so many settings but all in vain.... It's driving
me nuts.
Does anyone have a solution how to setup TS2000 along with
the SignaLink SL-1+ to work with FLDigi? PLEASE HELP!
?
VY73 de Ben (DL4DBM)
|
Re: TS-2000 Kenwood problem, PLEASE HELP
Look in the messages history of this group for message #33584 which has a useful description for a configuration like yours.
|
TS-2000 Kenwood problem, PLEASE HELP
Hello everybody!
I'm struggling with my TS2000 along with a SignaLink SL-1+ to work with FLDIGI.
First of all: I'm using this setup succesfully for a long time now with WSJT-X.
My notebook is connected via USB to the TS2000 and via 3,5mm Headphone-Jack to the SignaLink. The SignaLink is connected to the TS2000 via the 13-ACC-Connector.
?
Now to FLDigi:
In order to make the connection between the TS2000 and my notebook I'm using FLRig. So far so good.
This is my problem:
My notebook (FLDigi) is hearing the signals but only through the microphone of my notebook. If I turn down the volume of the TS2000 no signals are being decoded....
Sending is about the same problem: If I hit the tune-button of FLDigi the TS2000 switches to transmit but the SignaLink doesn't switch to "PTT" and the TS2000 expects audio from the microphon....
I've tried so many settings but all in vain.... It's driving me nuts.
Does anyone have a solution how to setup TS2000 along with the SignaLink SL-1+ to work with FLDigi? PLEASE HELP!
?
VY73 de Ben (DL4DBM)
|
Actually you can do this:
FLDigi -> FLRig
N3FJP -> Hamlib rigctlcom -> FLRig
WSJTX -> FLRig (via Hamlib)
rigctlcom is the magic glue that emulates a TS-2000 and can connect most any program (other than Ham Radio Deluxe) to FLRig or any other rig for that matter via a virtual serial port.
Mike W9MDB
toggle quoted message
Show quoted text
On Saturday, October 12, 2024 at 11:45:34 PM CDT, Philip - K4PO <k4po.ars@...> wrote:
Mike,
Either FLDigi or N3FJP logger can control the but only one can be connected at a time.? Best to let FLDigi do the CAT work and make log entries.? Same if you run WSJTx where you marry WSJTx to Jtalert then let Jtalert do the logging.
Phil / K4PO
|
Mike,
Either FLDigi or N3FJP logger can control the but only one can be connected at a time.? Best to let FLDigi do the CAT work and make log entries.? Same if you run WSJTx where you marry WSJTx to Jtalert then let Jtalert do the logging.
Phil / K4PO
?
?
|
That is the fault of the
user's browser and not the email url links.? Most email clients
will allow you to view the email source level contents by
pressing control-U when focused on the email:
Content-Type: text/html; charset=UTF-8
Content-Transfer-Encoding: 7bit
<html>
? <head>
??? <meta http-equiv="content-type" content="text/html;
charset=UTF-8">
? </head>
? <body>
??? <font size="4"><font face="monospace"><a
moz-do-not-send="true"
????????? href=>w1hkj web
site</a><br>
????? </font></font>
??? <h1>Index of /files/fldigi</h1>
??? <ul>
????? <li><a href=>
Parent Directory</a></li>
????? <li><a
?????????
href=>
????????? AppleAudioCodec.html</a></li>
????? <li><a
href=>
????????? CW_Transmit.html</a></li>
????? <li><a
href=>
????????? FLdigi_and_FMT_Mode_by_VE3YX.pdf</a></li>
????? <li><a
href=>
????????? FSK_Transmit.html</a></li>
????? <li><a
href=>
????????? alert_clips/</a></li>
????? <li><a
href=>
????????? flarq-help.zip</a></li>
????? <li><a
href=>
????????? flarq_help.pdf</a></li>
????? <li><a
?????????
href=>
????????? fldigi-4.2.06.tar.gz</a></li>
????? <li><a
?????????
href=>
????????? fldigi-4.2.06_LI.dmg</a></li>
????? <li><a
?????????
href=>
????????? fldigi-4.2.06_VN.dmg</a></li>
????? <li><a
?????????
href=>
????????? fldigi-4.2.06_setup.exe</a></li>
Note that the url reference is to http
and NOT https.? Some browsers, notably those on the Windows OS,
force the http reference to https.? An attempt on the part of the
browser developer to protect the user from shooting themselves in
the foot.
73, David, W1HKJ
On 10/12/24 08:50, Rich NE1EE wrote:
toggle quoted message
Show quoted text
See post
Link to W1HKJ software URL goes to wrong site
On 2024-10-12 09:30:, Nathan Rosenthal wrote:
Clicking directly on the links in Dave's latest post took me to the British website. Going through SourceForge does work properly.
|
See post
Link to W1HKJ software URL goes to wrong site
toggle quoted message
Show quoted text
On 2024-10-12 09:30:, Nathan Rosenthal wrote: Clicking directly on the links in Dave's latest post took me to the British website. Going through SourceForge does work properly.
|
These are the documents you
need for setting up the 7100 either for audio FSK or keyed FSK:
fldigi can then be used for
sending characters to the program flrig which in turn
generates the correct FSK keying signals to send to the 7100.
I would suggest you first
try using the 7100 in USB-D and sending the audio FSK to the
transceiver.? Be careful not to overdrive the audio, just like
you would if operating PSK-31 or any other digital mode.? RTTY
is simply another digital mode.
David, W1HKJ
On 10/11/24 20:22, Adrian Fewster
wrote:
toggle quoted message
Show quoted text
AFAIK, Fldigi only use's afsk for RTTY which means radio should
be in a suitable ssb mode.
Data-A or Data-L or USB or LSB, depending on program REV
selection for space mark polarity.
RTTY here is used for FSK, extFSK use, with RTS keying.
73
vk4tux
On 12/10/24 04:32, Don Rolph via
groups.io wrote:
Are you getting PTT signal sent (radio should go
into transmit mode)?
Are you putting out?any power (use power meter option on
IC-7100)?
Initially I could receive?but not send also.
I found the following helpful and when I reset according
to these instructions?all worked.:
Note: I had trouble with autobaud on CAT and a fixed
setting of 19200 seems to have resolved this issue.
On Fri, Oct 11, 2024 at
10:53?AM mike isakson via <w7xh.mike= [email protected]>
wrote:
Call sign W7XH
I am hoping to ask the group about a problem I am
having with my IC-7100 sending a continuous carrier . I
do not get? a diddle. I have tried both 4.1.20 and
4.2.05 fldigi and flrig 1.4.2 and 2.0.05.
I? have installed IC 7100 usb drivers and am
connected with a usb-a cable. The radio is set to RTTY .
I have rig control with flrig,fldigi, and N3FJP
operation. If I send a rtty message directly from the
radio, fldigi decodes it perfectly. I am just not able
to send.
73 Mike W7XH
--
|
Clicking directly on the links in Dave's latest post took me to the British website. Going through SourceForge does work properly.
|
Ok, then that is the issue. Set fldigi to Rtty mode and it'll probably do fine. Flrig has the capability key the transmitter I believe in FSK, but I've never done it. Hopefully someone can help in this.
toggle quoted message
Show quoted text
On Oct 11, 2024, at 17:33, mike isakson via < w7xh.mike@...> wrote:
yes the ic-7100 does fsk not asfk.?
In your first post, you said the radio was in RTTY mode. If the IC-7100 is like other recent Icom radios, RTTY mode is FSK RTTY, which needs an on-off FSK keying input. A constant carrier on a single frequency is what it will send if there is no FSK keying; this is a classic symptom of a radio in FSK mode without an FSK keying input. ? As I understand it, fldigi requires some external hardware to key FSK (either pseudoFSK, or a nanoIO, MORTTY or Navigator device). Some of the responses you are getting in this thread assume that you are using AFSK, meaning sound card modulation the same as other digital modes, not FSK keying. For AFSK the radio needs to be in USB-D mode, not RTTY mode. ? 73, Rich VE3KI ? ? On Fri, Oct 11, 2024 at 05:09 PM, mike isakson wrote: cliff, to be clear, fldigi cq call keys the transmitter. The problem is that it is a constant tone during transmission. There is no diddledhen the transmitter is keyed. ? 73 Mike
Mike, ? Sounds to me like a sound card issue. Not connecting on transmit. Maybe on wrong channel or need to put it on both channels?? ? What about other modes? Do they work ok on transmit? On Oct 11, 2024, at 15:00, mike isakson via ??< w7xh.mike@...> wrote:
Don, if I try to send a cq , the transmitter is keyed but i get a constant carrier sound no dittle. I use flrig, fldigi and n3fjp and rig control is great, if I send rtty from the radio directly it decodes in fldigi. I will look at the link you provided. Thanks for your response. 73 W7XH Mike Are you getting PTT signal sent (radio should go into transmit mode)? ? Are you putting out?any power (use power meter option on IC-7100)? ? Initially I could receive?but not send also. ? I found the following helpful and when I reset according to these instructions?all worked.: ? ? Note: I had trouble with autobaud on CAT and a fixed setting of 19200 seems to have resolved this issue. ? ?
On Fri, Oct 11, 2024 at 10:53?AM mike isakson via ??<w7xh.mike= [email protected]> wrote: Call sign W7XH ? I am hoping to ask the group about a problem I am having with my IC-7100 sending a continuous carrier . I do not get? a diddle. I have tried both 4.1.20 and 4.2.05 fldigi and flrig 1.4.2 and 2.0.05. ? I? have installed IC 7100 usb drivers and am connected with a usb-a cable. The radio is set to RTTY . I have rig control with flrig,fldigi, and N3FJP operation. If I send a rtty message directly from the radio, fldigi decodes it perfectly. I am just not able to send. ? 73 Mike W7XH ? ?
? --?
? ?
?
?
|
K5EIS - Tom
Dave
Rich NE1EE