开云体育

Louis, If you are using MS Edge and MS Defender you will have to ‘Keep’ the download 2 times during the process. Start the download from the ‘Release Notes’ page; a ‘Downloads’ sidebar

Lou, A lot depends on which form of Antivirus you have on the computer. Each will present a similar but different message. All of them boil down to it saying: We haven't seen this file very often.

Lou, Are you using a 3rd party anti-virus package? If so, which one? The help page that was updated today describes the steps required for Microsoft Defender. If you could provide a screenshot of

I have been a JMRI user from the days of the infamous lawsuit... Happenings of the last two years have kept me out of Model Railroading and JMRI.? Trying to restart with a new location and layout. I

-- Peter Ulvestad JMRI Users Group Moderator ( https://www.jmri.org ) Tam Valley Group Moderator ( https://tamvalleydepot.com/ ) Sprog-DCC Group Moderator ( http://www.sprog-dcc.co.uk/ ) Edmonton

Actually you are wrong on this. <family name="Basic FX" mfg="Digitrax" lowVersionID="91" highVersionID="111"> If you hoover your pointer above it, it will show what version numbers -- Peter

I found it in the "basic Fx" group. Some simple decoders do not have read enabled. And the definition has 0 in CV7/8, so nothing JMRI can read to get the version. -- --- Thomas DeSoto, TX

This has happened to me a few times, as recently as a couple of days ago.? In my case inevitably it is because I have made some change to the properties of the classification track and it no longer

On Sun, Sep 22, 2024 at 05:10 PM, Rick Stoneking wrote: > > Currently, when I build the train (YB10) it will typically leave the yard > with the 10 cars and set all 10 of those cars out at the

Scott, You only need to assign a new block to the lower half. This happens to be the A and B connections. You will need to remove and add SM6-77-78 since it now has a different block boundary.

Keith, When I create a NX warrant, I do a "Save" before the warrant finishes. This creates a copy with a new name. Dave Sand

Group; I have been trying to work on more Warrants, but I keep having a problem:? I can create a N-X warrant and it runs, but when I try to duplicate the warrant by "create new warrant", it fails,

Thanks, Dave. ?I have updated the crossover to have a different block on each of the different legs but I still could not get the logic to build for that signal mast. ?In fact, now another signal

Eric, I use custom loads in a couple of specific places (Ash pit generates a load of ash, and the cement factory receives cars with ash loads, etc.) but creating custom loads for every industry and

Hi CLL, The RosterEntry attributes Operating Duration and Last Operated are set when a Throttle has been obtained BY ROSTER ENTRY ( not just DCC Address ) and this Throttle is released. Larger

What triggers the database to update the last operated date and what triggers the operating duration? I’m going to guess and say using the JMRI throttle. Therefore, I ask, can the command monitor

I put a reply to this earlier, but it seems to have not gone out to all in this group, so trying again. Rick, I have found that by using custom loads and schedules, the cars all have final

Pete, I will attempt to provide a clearer, and more complete, explanation of what I am trying to do. My RR has two yards at the South (Baltimore) and North (York) terminus of the railroad.? In

I installed the decoder and it does run correctly as loco number 3. I wanted to change the loco number so I used "New Loco" , "Read type from decoder" steps to try to add it into DecoderPro. The

Scott, You cannot have the same block on both halves of a crossover. The route logic only finds the neighbor on the straight route, in this case the stub track. Dave Sand