开云体育

Getting back to the original question you asked, no, there’s not a simple setup to hold an Internal Turnout in one position. You can create a Logix that looks for the Turnout to change, and

"Verbal feedback" is for QSI decoders only and is on the QSI Misc tab and is called "Programming Verbal Acknowledgement".? It's bit 0 of CV 62.? But it only applies to Ops Mode programming (POM),

In the turnout edit you should have a Feedback tab. In there you can select the one or two sensor option. After that, you'd be able to enter the sensors for the feedback. -Ken Cameron, Member JMRI

I bought a zimo MX478W decoder to activate a servomotor. I find no reference in the list JMRI... Sincerely ~JES~

I have all the turnouts added as Internal (with addressing IT.IOT$40:0:10.0.0.100) and this is probably the problem. When adding internal turnout there are no options 1/2 wire nor maintained/pulse

There are options when you set up a turnout to make it one wire or two wire. I assume you are using the default which I believe is 2 wire. You can also the output type to maintained or pulse. Try

Is there an option to setup turnout permanently in one position? I mean when I set it up in JMRI to CLOSED and someone will change it's position by hand on the layout to THROWN JMRI will put it back

Dave, ? I don't save logix if I know there are errors, but I this is one which does:- ?IX:AUTO:0001C1? C1?? ?? Antecedent: (R1 and R2) or (R3 and R4)? ??? [x]? R1? IF? Turnout "pt01"

That makes sense to me. The failures are because the command station (Zephyr+) is connected to my programming track. There would logically be all failures. Thanks all. John Griffin -- John

Ken, I found 1, 2, and 3. They were all good. Where do I find the "verbal feedback" option at? Also are you saying to remove the grain of wheat bulb? I also have gone back to 4.12 version. I have also

I have upgraded many times without problems, but my latest upgrade has failed. I am running on a Toshiba C655, Win 10, Java 8 181, with a Locobuffer USB connected to a Digitrax DCS 200. No error

Hi Try a resistor between 500 and 2k ohms for Lenz, tcs. The value of the resistor matters. The BLI decoders need the audio feed back disabled. Steve G.

I just bought 5 emd locos from broadway limited. They are the new sound decoders something3 Jmri will not identify the decoder on a random basis. Try selecting the decoder from the list and write a

I was never able to consistently read TCS, Lenz and NCE N-scale decoders with an original Zephyr, either direct from the command station, or with DecoderPro running on a Linux laptop connected with a

Cwt, First I'd suggest you stick with 4.12, there are issues in 4.10 that are likely to bite you sometime. Next, make sure you can select if you use the PowerPax and select to disconnect the grain of

I am using version 4.10 and have tried 4.12 JMRI on windows 10. I also am using a RR-CirKits LocoBuffer-USB version 3 on com port 3, a Digitrax DCS 200 and a program booster (PowerPax) to the program

Thanks Steve Yes I did that and all are well now, regards Manos SV1IW

Hi Manos You saved them: tools->file->save->save configurations only to file. Then to load: Panels->Open Panels Steve G.

Thanks again Ken, got them all sorted out, so far. If I load the tables from panel menu (had them saved with a different name) all return as expected. The reason I didn't do this before is that

John, What you are seeing is one of two things. First it could be the command station. When it does a power on to the track, it sends special commands (what you see) to ask all devices on the layout