Re: Reconversion from 11M Local Oscillator alignment
Unplug the two wire harnesses from the display unit and clean the male pins. Plug them back in a few times to make sure all of them or connecting well. Retest.? If no good: As lame?as it sounds, I¡¯d buy a new display unit on eBay, swap it out with the one in the radio now and if still no difference, put it back on eBay! You won¡¯t get stuck with it, they sell fairly easily.?
On Thu, Jun 20, 2024 at 5:40?AM Chuck, WS1L via <chandlerusm= [email protected]> wrote: Would that be the case for a 101ZD MkII?? I've never seen any toggle switches on the VFO although they could be inside the housing. ---------- Forwarded message --------- From: Bruce Collins via <kb0tj1=[email protected]>Date: Wed, Jun 19, 2024 at 12:40?PM Subject: Re: [Yaesu-FT-101] Reconversion from 11M Local Oscillator alignment To: < [email protected]> I¡¯m pretty sure if it is showing MHz ?off, but is actually transmitting and receiving at the right frequency ¡ it has nothing to do with the new 10m crystals.?
The older display units had toggle switches on them that mix signals to give you the right offset displays.?
Maybe better check that out in case it is adjustable.?
|
Re: Reconversion from 11M Local Oscillator alignment
Thanks for that - is it any clue that this only happens when transmitting and the power is increased?? I was suspecting a supply voltage issue perhaps with the additional drain on TX.
Also, since it happens on 10m, 12m and 15m, I would suspect an issue with the actual display board or VFO board ?
I have had to remove these VFOs a few times over the years and remove the VFO cover, ?to just resolder every single joint on them to get the display to work right again.?
|
Reconversion from 11M Local Oscillator alignment
Would that be the case for a 101ZD MkII?? I've never seen any toggle switches on the VFO although they could be inside the housing. ---------- Forwarded message --------- From: Bruce Collins via <kb0tj1=[email protected]>Date: Wed, Jun 19, 2024 at 12:40?PM Subject: Re: [Yaesu-FT-101] Reconversion from 11M Local Oscillator alignment To: < [email protected]> I¡¯m pretty sure if it is showing MHz ?off, but is actually transmitting and receiving at the right frequency ¡ it has nothing to do with the new 10m crystals.?
The older display units had toggle switches on them that mix signals to give you the right offset displays.?
Maybe better check that out in case it is adjustable.?
|
Re: FT-101EE installing Processor board PB-1534
James
You can find instruction at
section 6-1.
73 Emerson PP6EW
Em seg., 17 de jun. de 2024 ¨¤s 15:43, James Fisher via <cadiscase= [email protected]> escreveu:
I just got a FT-101EE.
It has the PB-1534 Processor board installed.
It works good except :
When in transmit and the meter is in the ALC position, there is no movement of the meter.
Yes I have turned the mic gain up CW.
I tried adjusting the ALC on PB-1184? but it makes no difference .? The needle is pined to the right.?
I read where the ALC adjustment is located on PB-1534.
I can move VR2 and it does move the needle to the left, but still no 'uptick' when I modulate USB
Are there issues with installing the PB-1534 in a FT-101 EE? ??
Are there any instructions for installing? the PB-1534 in an EE ?
Thanks
James
|
Re: Reconversion from 11M Local Oscillator alignment
Also, since it happens on 10m, 12m and 15m, I would suspect an issue with the actual display board or VFO board ?
I have had to remove these VFOs a few times over the years and remove the VFO cover, ?to just resolder every single joint on them to get the display to work right again.?
|
Re: Reconversion from 11M Local Oscillator alignment
I¡¯m pretty sure if it is showing MHz ?off, but is actually transmitting and receiving at the right frequency ¡ it has nothing to do with the new 10m crystals.?
The older display units had toggle switches on them that mix signals to give you the right offset displays.?
Maybe better check that out in case it is adjustable.?
|
Reconversion from 11M Local Oscillator alignment
I have a FT-101ZD late Mk2 that had been converted to 11M years ago.? I recently got around to locating the correct crystals and have aligned the TX mixer, driver and RX front end stages per the service manual.? I get good output on all bands and good sensitivity as well.??
However, when transmitting on 15, 12 and 10 meters with more than a few watts of output, the VFO shows an incorrect frequency - several MHz low, not always the same.? Checking the output on another radio shows the transmitted signal is where it should be, so it's the VFO that is displaying the wrong frequency.??
I suspect I need to align the premix local board where the proper crystals have been installed, but the service manual is a bit brief in it's description of the process.??
Does anyone have a "cheat sheet" for this, or perhaps someone has done a video?? I have an oscilloscope, and could whip up a simple RF probe if needed.??
|
Re: FoxTango laminated sheet
If you are on Facebook, go to the files section of the group called: Keeping The Yaesu FT-101 Alive! ?
|
The Fox Tango Club used to have a laminated sheet with Top/Bottom of a FT 101 with alignment points indicated.
Does anyone have a digital copy of this document they could send me ?
Is it still available to buy ?
Thanks
James? NQ7L? ? ? cadiscase@...
|
FT-101EE installing Processor board PB-1534
I just got a FT-101EE.
It has the PB-1534 Processor board installed.
It works good except :
When in transmit and the meter is in the ALC position, there is no movement of the meter.
Yes I have turned the mic gain up CW.
I tried adjusting the ALC on PB-1184? but it makes no difference . ?The needle is pined to the right.?
I read where the ALC adjustment is located on PB-1534.
I can move VR2 and it does move the needle to the left, but still no 'uptick' when I modulate USB
Are there issues with installing the PB-1534 in a FT-101 EE? ??
Are there any instructions for installing? the PB-1534 in an EE ?
Thanks
James
|
Re: Electrolytics - FT-101B
Sorry- my reply never went through.? Yes, I have the cap on the audio choke.
|
Re: Electrolytics - FT-101B
The wire wound resistors were OK. I cleaned the flying lead contacts and pins on tubes and tested the drive tube, which was OK. No tester was available for the PA tubes. Re-installed tubes and everything worked.
Completed the Rx and Tx alignment process and started 'on air' testing. Power out is low, (20 to 80 watts)? and Rx and TX frequencies do not match. (People have said 'You are off-frequency' every time I've made contacts on this radio.)? I have seen videos on fixing the latter issue and will try to locate matching tunes to get power level up.?
This thing is slowly rejoining the land of the living, but I have to say that using it makes me appreciate my TS590sg!
|
Re: Electrolytics - FT-101B
I ran into similar discrepancies when I resurrected my 101E after nearly 30 years in storage. The comments I got back from reputable service people was that tables were "generally accurate" but not to be considered to be dead on. As long as they were steady and nothing seemed to be "suffering" they were OK.
Check to see if the wire wound .6ohm resistor, located on the bottom of the power tube sockets, has been blown open from excessive current.?
if yes, you might have bad power tubes too.?
|
Re: Electrolytics - FT-101B
Check to see if the wire wound .6ohm resistor, located on the bottom of the power tube sockets, has been blown open from excessive current.?
if yes, you might have bad power tubes too.?
|
Theses relays are not hard to find on eBay.?
Not sure I¡¯d bother with tearing into rewiring that socket!!
|
Looking for a replacement for RL1. I think the one in my FT101B has the "tired spring" mentioned in the service manual.? Potter & Brumfield part R10-E1X6-V90 looks like it might work with a bit of wiring change.? Interested to hear if anyone has tried this and what the result was.
|
Re: Electrolytics - FT-101B
Cleaned contacts in both relays with card stock and deoxit. Both were visibly dirty. Fired radio up and receive is OK, but I could not get any idle current in Tune mode. I checked rectifier board supply lines and saw:
+748v (vs +600v theory)
-180.7v vs -100v theory
+182.3v vs +150 v
11.5v AC is 10.5v AC
+14.2v vs +13.5v
Yikes!
No sign of damage anywhere. Re-seated relays, but no change. Checking tube now.? The PA tubes are different brands, so I'm guessing all 3 will be replaced before aligning the thing. But right now the big thing seems to be weirdness with power.
I feel snake-bit. Suggestions, anyone?
73,
Tom AI4TH [was KO4HNB]
|
Re: FT-101EE: Good RX-No TX
Vince
A source of Tx problems is often Q3 (2sc784R) at PB 1181B RF unit.
good luck Emerson, PP6EW
Em sex., 31 de mai. de 2024 ¨¤s 10:36, Vince, KN6KKZ via <vf6fhellcat= [email protected]> escreveu:
? I have been away from this project a while and I am eager to get back to work on diagnosing and repairing the TX issue. This FT-101EE receives beautifully, and the S-meter seems to work properly in indicating received signal strength. When PTT or MOX is keyed, the S-meter needle (PO position) jumps to the left, against the resting pin. The movement is only a fraction of a mm, but just enough to observe it being forced the wrong way. The instant PTT/MOX is released, the needle momentarily spikes up to around S5 before coming back to rest on the pin. This same condition occurs on all bands against a dummy load. The needle spike that occurs after releasing PTT/MOX is to around S5 in USB, but when in LSB or AM mode it only spikes up to around S1 (max carrier).?
Just hoping this symptom might throw up a flag for someone and help me narrow down the source of the issue.
Thank you,
Vince, KN6KKZ
|
Tom, I value and appreciate moral support. Helps keep up the fighting spirit. I am hoping that I can get the original NEC tubes tested tomorrow to rule them out. I have new C13, C131 and C11 mica caps in hand that I know I should change, but I¡¯ve been a bit intimidated by getting to C13. Looks like the face has to come off to remove the chassis side bar to get in there. I don¡¯t believe this echo-echo has been touched by a #2 Phillips or a soldering iron since it left Japan. Still has the protective film over the panel.
73, Vince, KN6KKZ
|
Wish I could offer more than moral support, but I' m fighting the same issue with a 101B.? Every time I correct one thing it uncovers something else.? Bad rectifier board, dirty relays, mismatched PA tubes.? Looks like this could be a long running project!
|
Bruce Collins
Chuck, WS1L
Tom ai4th
Ron, N1BHE
Vince, KN6KKZ