开云体育

I second that comment about the "component tester" Clay! 100% We should have a thread about inexpensive CDV-700 related test equipment. There are even inexpensive oscilloscopes and scope-meters out

OK MichaelC. Don't dismay. You have a good housing, a good meter etc. Would you consider sending just the PCB to me and let me look at it? Then you can move on to your next project but keep the

This is where the cheap “Multi-Function tester TC1” or similar shine. They can help test and determine the type of component like resistors, capacitors, inductors, diodes/LEDs, transistors (MOS

yessir... this one is a puzzle.. maybe it is scrap. new transformer - got to buzzing, got at least some HV going - up to 500V expected 15V is low at 5.7V measured between C1 (-) and meter. V2 base is

OK good to know. No need then probably. Have you traced all the PCB paths with an Ohmmeter already? Sounds like you've done everything right so far. Geo To: "CDV700CLUB" <[email protected]> Sent:

yes I can reinstall the old ones.. and I built my last two Lenis with these Russian transistors and they worked fine.

can you put back in the original transistors? or maybe put some russian ones in the other unit, see if the work there? They for sure sent you germanium PNP's right? Geo To: "CDV700CLUB"

Yes.? it is installed correctly.

it sounds right but I don't have schematic right here. It's the one that is attached to to transformer primary winding. Geo To: "CDV700CLUB" <[email protected]> Sent: Friday, May 13, 2022 3:29:45

holding the russian transistor legs up.. the base is the lead grounded to the case.? with the base at the bottom,? the collector is to the left, the emitter to the right.? Flipped over to stick in

" I cannot produce clicks in the speaker by tapping R12-C5 junction. Voltages at V2 and V3 are all screwed up. At V2, supposed to get .05V at the base - I get way high. V2 collector supposed to get

hi Geo..? ?the -15V diode.. is that CR4?

Good on the 1G Meter MichaelC! Tell you what, try removing the -15V diode, see what the HV does. Geo To: "CDV700CLUB" <[email protected]> Sent: Friday, May 13, 2022 2:20:42 PM Subject: Re:

yes, I am using a 1Gohm HV Probe.? and reading the manual it says if the 15V measured at point 6A ( negative end of C1 to meter) is low, replace rectifier CR4. so replaced CR4.? I still measure only

Well, maybe not. If you are using a 1,000,000,000 Ohm ( 1G Ohm or 1000 M Ohm) input meter, yes. Otherwise if you use a typical 10M Ohm type meter, you won't get but maybe half the real reading.Read

ok I got some measurements. I am getting 3V to pin 6 of the transformer, per the schematic. I am supposed to get 15V at R5 - only getting 5.6V.? ? and I have a question:? in the ENI manual on the

There's a kit for that, but you're handy with tools, so best learn to do it yourself, especially of you might be doing many more for yourself or others. Geo To: "CDV700CLUB" <[email protected]>

ok George, will give it a whirl.? I need to wire the battery tray so I can have it off to the side and out of the way.

" I now have a happily buzzing transformer. I still don't have HV to the probe - using a HV probe, I get nothing on the hot wire going to the probe." Start at the transformer leg, measure AC Volts

Hi MichaelC. Have you reached the point in the LENi conversion where you take a hacksaw to the battery holder box? When you cut is in half, leave a little shelf at the meter end of the now 2 Cell