|
Dumb question but on one of my computers I can't seem to expand upward the waterfall. What setting in FLDIGI config file do move the waterfall up and down. Thanks Dave -- 73's de NU4N
|
|
MacBook OS and Failure to Transmit
20
I am fairly new to Fldigi (three years experience) and have a question. I recently upgraded my 2024 MacBook Pro to Sequoia 15.3.1 OS. Ever since the upgrade, Fldigi fails to key my radio transmitter. Messages in the ¡°transmit pane¡± are being in being sent as they appear in the "received pane", but the radio transmitter is not being keyed. My set up is as follows. MacBook Pro - Sequoia 15.3.1 OS Radio Kenwood Th-D 74 Fldigi 4.2.08 Soundcard. Digirig I am including a file, listing my configuration settings. (See below) It is important to note that prior to the latest Mac OS upgrade, Fldigi was working perfectly. Is there any information regarding this problem? Thank you! Tom Thomas M. (Tom) Fields. WA7CHF 14 Bowline Ct. Belllingham, WA. 98229-7902 (360) 676-6604 (R) (360) 319-3947. (C) fieldstom45@...
|
|
Greetings, I have an issue with the Perseus with FLDigi an BlackCat WEFAX (the only two decoders that I have. Note the vertical interference marks showing on both decoders. However on the Perseus, there is not such interference shown in the spectrum nor the waterfall view. Both picture attached to show the Perseus is not showing the interference When I use my RSPdx and HF+ Discovery, this situation does NOT occur. I am using the same antenna for all three radios. I have tried the Perseus/decoders set with a VAC and also the signal to the PC speakers. Does anyone have any possible ideas what might be causing the vertical interference lines? By the way, I have tried powering the Perseus with a PSU from Jameco and with a USB cable. One more thing: I can not get the brightness and the other slide switches to work on the right-hand side next to the spectrum/waterfall screen. I have never notices an issue before. Regards, George
|
|
I'm in the process of learning CW, using the MorseMania app and I'm doing really well on instant character recognition, but I have 0 sending skills at the moment. I'd like to use FLRIG or FLDIGI to send CW but I'm having problems... when I use the CW Keyer in FLRIG, it doesn't trigger the IC-7300 to transmit? If I use the same application to do FSK Keyer - it works fine... And so does the "PTT" and "TUNE" button on the main FLRIG window... Anyone have experiences with FLRIG and the IC-7300 CAT PTT? Here is how I have FLRIG configured: Any and all reasonable suggestions are greatly appreciated ? 73 de KZ4JN
|
|
I am having problems doing CW Keying from the FLRIG program. When I go to Keyer | CW Keyer and type a message and press Send/Pause, the transmitter doesn't transmit but the software acts as if though it is (marquees the message that I typed). If I do the same but use the FSK Keyer - it DOES trigger the rig to transmit.. I have the following settings for Xcvr and PTT-Generic: Can someone help me figure this out? I am hope that fixing this - will carry over to CW working in FLDIGI as well.. Oh - while I'm at it - can you tell me - when you use FLDIGI to transmit/decode CW with the IC-7300, is your radio set to CW or LSB-D/USB-D ? Thank you!
|
|
Greetings, I am using the latest version of FLDigi on my Win 10 desktop. I was trying to select one of my Virtual Audio Cables and I get the message shown on the attached picture. I have Restarted the computer and the message persists. How can I clear this error and select the input that I want? I have attached the screen capture and the VAC Control Panel. I would appreciate any help with this issue. Thanks, George, NJ3H Redmond, Oregon USA
|
|
How to log to DXKeeper?
3
Can I have fldigi log to DXKeeper, and if so how? Thanks, Gordon - n1mgo
|
|
fldigi .26 source
Ken, Please try the .26 tar.gz found at https://www.w1hkj.com/alpha/fldigi/ David
|
|
fldigi development test version posted
3
at https://www.w1hkj.org/alpha/fldigi/ fldigi-4.2.06.25.tar.gz2025-03-21 07:414.9M fldigi-4.2.06.25_set..>2025-03-21 07:416.6M fldigi-dark-scheme.png2025-03-21 07:41122K readme.dmg.txt2025-03-21 07:41532 readme.txt2025-03-21 07:41877K Alpha * version 4.2.06.24 frequency lock status * save and restore frequency lock status between sessions run_script * add new command line parameter . script <fullpathname filename> 73, David, W1HKJ
|
|
I cannot find any recent information on this and I am stumped. I have a Ten Tec Jupiter (TT-538) and am running fldigi 4.1.14 and flrig 1.3.51 on Windows 10. I have been running fldigi with no problem for 4 years, but I have never gotten flrig to work. Cat control works with other programs. The current problem I have is that flrig tells me: "Transceiver not responding" and to reset the com port. The com port is correct and available. There aren't many other options. It's a Prolific USB-Serial cable, not FTDI. Any ideas? -- 73, Lem W1LEM
|
|
New Computer
3
Hello, I've been using a WIN7 Toshiba Satellite for a long time. It is loaded with FLDIGI 4.0.18 and works quite well. I decided to move up to WIN10 and purchased a refurb Dell Optiplex 7010 quad core intel i7 3.4GB DDR3 ram ITB SSD running WIN10 pro. I tried using my Easy Digi by KF5INZ. Downloaded the latest config of FlDigi and not having much success interfacing with my Yaesu FTDX1200. Any ideas would be greatly appreciated. Just remember I'm a dinosaur stumbling along trying to figure this out. Thank you, Ron Speer W6RRS
|
|
I want the LK button to be ON when I start up Fldigi. I know that a script can accomplish this task. I don't want to push the buttons to execute the script. I want the LK button ON every time I start Fldigi without having to push any other buttons. Can this be done? If so, how? Thanks. -Randy, W4IFI
|
|
IC7300 CW with FlDigi 4.2.06
6
I had it working fairly well but now, suddenly - something has happened so as my IC7300 is transmitting the tone, the radio releases the PTT , pauses and reengages the PTT and continues!? I read https://sourceforge.net/p/fldigi/wiki/IC7300_CW_howto/ and followed the instructions for using FLRIG and FLDIGI together but it's just not working like it used to. It used to trigger the transmitter and FlDigi would pulse its tones and once finished - it'd switch back to receive mode.. I don't believe I used to have to enable break-in or full break-in.. If I don't do that now - then I can HEAR the tone but it is never transmitted. Any suggestions?
|
|
TenTec Jupiter FLRig config - help
2
Hi all, I am trying to connect my Jupiter to FLRig v2.0.05 on Win11. The connection is USB. I know the connection works. I have used it successfully with Winlink RMS Trimode. I tried the 'standard' config that comes up when I click on TT-538. All baud is 57600. 1 Stop bit RTS/CTS on RTS +12v on DTR +12 v off I tried the connection that works in Trimode RTS on DTR on Has anyone gotten their Jupiter to connect with this USB connection? Thanks -- 73, Rory Griffin W4RJG
|
|
No modulation rtty but decode ok.
7
Setup: Icom ic7700. Interface rigexpert TI5000. hello. it only outputs tone and power, without shift. I am on the settings of another device. the macros are functional with another station. the rigexpert TI5000 interface creates 4 ports. (fsk/ptt/cat/cw). the sound card is identified, I tried the 3 possibilities. I tried the cat with hamlib and rigcat. fsk modem I give it the fsk port. Anyone have any idea? 73 f5ind chris Jean-Christophe BARB?RA
|
|
<MAPIT> MACRO
3
#fldigi-parameters
I am installing FLDIG on a new laptop. I have in my log off macro <MAPIT>. I forgot how to get to work? Was it Google Earth? Appreciate the help. Dave -- 73's de NU4N
|
|
I am trying to figure out how I can use FLRIGs to switch my spectrum scope between center/fixed/scroll-C and SCROLL-F mode. Has anyone figured out how to do this? According to the full manual - page 19-14, you'd use the "27" command like this: But if I send 27 0000 or 27 001, it doesn't change? Any suggestions or advice is greatly appreciated! -- Anders Georgsson KZ4JN/WSDF851
|
|
I am in the process of moving the entire w1hkj web site to be hosted at QTH.com. The new site is https://www.w1hkj.or Please visit the site and report any discrepancies, particularly misdirection of links. fldigi, flrig, etal still need to be modified to reflect this move to the QTH host. 73, David W1HKJ
|
|
CW & RTTY with legacy rig ICOM IC720A
Please give me a hint, if I think the right way: IC 720A has a classic PTT-input (a switch at the mike) and a morse key input. It supports VOX. Here are my thoughts, how to connect them: For RTTY: - using the soundcard is simple and already working. - how do I manage the PTT? Why not use the ?VOX¡°-function, that switch the tx on, when there is a signal from the soundcard? Will that be working? But for CW: - sound RX already working fine. - how is the keying done? Does fldigi use "1000 Hz on right soundcard output¡° for CW-Keying? Is the 1000Hz-signal the signal for morse output? PTT looks quite similar to my morse key interface. When I use ?VOX¡° in CW-MODE the IC720 switches to ?send¡°. I just hit the key and transmittion starts. WrapUP: Can I manage it like this: For RTTY: Use solely the VOX-function. Nothing else. For CW: Build a 1000Hz-interface and connect it to the morse key input? I did not find an info (that I understood :-)) in 500 pages of docu. vy 73 Mike | DL1MKP
|
|
hello everyone. setup: ft991a in usb. window 10. there is no rtty modulation. i searched here, in the previous messages, i browsed a lot of internet pages, also the software help. i managed to decode, to try to make it work, now the decoding is done in reverse. the radio goes into transmission in rtty mode (lsb or usb), there is only one carrier and the power comes out. in ssb mode, it does not go into transmission. for info, this radio works correctly with mmtty and 2tone. Tank you for your help. Chris F5ind
|
Image Name
Sat 8:39am
Sat 8:39am