¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Winfldigi
  2. Messages
Expanded Topics Messages Polls
Date
Re: FLAMP Question: block fills from old queue ID?

 

Great.? I'm using 2.2.09 and the relay files arent supported.? So is the alpha version OK?? Any idea where I can get the released 2.2.12.0???
?
Thanks!
Re: Yaesu 991A the tune button doesn't work

 

Hello Dave,
?
Yes, of course, I am glad to help to the community!
?
73! de HA3MGA Gabor
Re: FLDIGI & FT-991A Settings

 

Hello Howard,
?
Unfortunately no clue. However, if you followed my tutorial, then even for CW in Fldigi, the radio must be in Data USB or maybe in Data LSB mode.
?
73,
?
Gabor
Re: FLAMP Question: block fills from old queue ID?

 

Yes FLAMP can,

For transmitted files just reload the same file, but you must remember what format it was sent with, i.e. block size, compressed, file timestamp change (by moving, editing, copying), etc as these states changes will change the file HASH value. File stamp changes are caused by any process that touches said file.

On the receive side there is a configure option that can save the relay files on program exit, or under the file menu you can load and save the relay files. Relay files are verbatim copies of the data received from FLDIGI. This data can not be altered (edited) as the checksum will fail upon reception.

This statement is based on this version which can be found here. (version 2.2.12.04). Its an alpha version but is currently slated to be the next release.

Robert
FLAMP Question: block fills from old queue ID?

 

I've filled blocks and relayed blocks, but never if I had already closed flamp.
?
So, lets say I transmitted a file via flamp and someone didnt get their block fills.? Then, later after I've already closed flamp, they tell me about it.? Is there a way I can being up the same file and transmit/relay the missing blocks with the original queue ID?
?
Hope that made sense.
?
--- W4MRP
?
Re: FLRIG 2.0.04 + TS590SG, DSP Filter Selection in DATA while using "Lo/Hi" Mode

 

I just responded on this issue in a separate thread.

You are correct. The flrig module (source code) for the 590SG is based on the earlier 590S module. The 590S did not support hi-lo filters for data modes, so the flrig module is unaware of that capability and the UI does not function as desired with respect to the filter mode and filter settings.

I have good intentions to work on an update to the flrig module for the 590SG to make some changes where the SG model behaves differently than the S-model, but I haven't gotten around to it yet.? In the meantime, you can configure Command buttons to send the SL and SH commands, etc., to switch the filters between shift-width and hi-lo cut mode, and to supply your desired filter settings.? I use these on a daily basis and they work perfectly.

73 de AE4ON

On Sun, Aug 18, 2024 at 4:52?PM Eric Hidle via <eric.hidle=[email protected]> wrote:
When using flrig 2.0.04 with my ts-590sg, if I have the radio set to use "Lo/Hi" filter mode instead of "Width/Shift" mode in the DATA mode, flrig does not seem to know how to handle this. Has anyone else observed this or can someone else confirm this behavior?
Thanks in advance!
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

 

FYI, there are some features of the 590SG that are not supported by flrig.? I raised some of these concerns previously, and I believe Dave confirmed that he did not have a 590SG radio to test with, and the flrig?module was based on the earlier 590/590S module that was developed with testing performed by a friend who is now a SK.? As an example, the 590SG supports both shift-width and hi-lo filters for both data and non-data modes.? The earlier models did not support that flexibility. In those releases, data modes were limited to shift-width filters so the filter controls in the flrig UI don't necessarily work properly?for a 590SG depending on your usage.

I downloaded the flrig source code, confirmed that I could compile it and build a local version, and I identified some places where some enhancements could be made, but I haven't had time to implement those changes yet.? Possibly the behavior of the meters is another area where the source code for the 590SG rig module could be enhanced or fixed.

What I have done for those features that I require where the UI does not support the capabilities, is to set up Command buttons to send those command sequences.? So I have created command buttons to switch between shift-width and hi-lo filters and to set the width and the hi-lo cut values.? As soon as I have time, I plan to test some modifications to the 590SG module and will submit those for review, testing, and inclusion in the future release.

There may be another solution to the meters issue. I haven't looked at those previously, but I will add that to the items I will look at when I make those improvements to the module for this rig. Possibly the parsing of the response is something that needs to be done in the rig-specific module.
73 de AE4ON

On Mon, Aug 19, 2024 at 10:37?AM Eric Hidle via <eric.hidle=[email protected]> wrote:
Looking at ts590sg.cxx in the source, there do not appear to be any functions here that would read the meters via an RM; command, so I guess we just don't have that functionality for our radio. Perhaps it can be added at some point.

Maybe it's tricky because the radio responds to an RM; with a string that contains responses for all three meters:

RM10000;RM20000;RM30000;

Which are the SWR, COMP, and ALC meters, respectively, in the unit of "number of dots on the display," which then must be converted to a value for each meter.

Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

 

Looking at ts590sg.cxx in the source, there do not appear to be any functions here that would read the meters via an RM; command, so I guess we just don't have that functionality for our radio. Perhaps it can be added at some point.

Maybe it's tricky because the radio responds to an RM; with a string that contains responses for all three meters:

RM10000;RM20000;RM30000;

Which are the SWR, COMP, and ALC meters, respectively, in the unit of "number of dots on the display," which then must be converted to a value for each meter.

Anyway... there we are.
Eric


On Mon, 19 Aug 2024 at 11:01, Eric Hidle <eric.hidle@...> wrote:
Okay so I sniffed the serial port between the PC and the radio while the SG was transmitting, and flrig does not appear to be sending any "RM;" commands to the radio, so it is basically not trying to read the meters.

I did verify that all the meters were checked in the Config -> Setup -> Polling menu.
Thanks
Eric

On Mon, 19 Aug 2024 at 10:24, Cliff via <ae5zaham=[email protected]> wrote:
Right, it sticks if you close flrig with it displayed, but if you close the dialog then close flrig it will not come up next time unless you go to config and request it again. At least that is the way it works here and should work.

73,
Cliff, AE5ZA



On Aug 19, 2024, at 09:16, Philip Rose via <gm3zza@...> wrote:

Cliff,

If you Save Prefs, the I am glad that it sticks. You either use it or you dont. Either way you want flrig to start each time the way you use it.

Phil GM3ZZA



On 19 August 2024, at 15:09, Cliff <ae5zaham@...> wrote:


Wayne,

The meters dialog is brought up with the Config/UI setting as in the screenshot below, however it is not a setting that should stick. Closing the dialog should close it and next time it should not come up on its own. You might have a corrupted configuration file. To test that go to C:\Users\<login-name>\flrig.files\ directory and rename the ts590sg.prefs file to something else and resetup the config. See if that makes any difference.


73,
Cliff, AE5ZA



On Aug 19, 2024, at 08:05, Wayne Carpenter KN2Z @minicowman via??<mwcarpe@...> wrote:

I have a very similar issue with my 590sg.. Only the S meter works on RX and PO works on TX.? SWR, ALC, whatever IDD is, and Volts all remain clear regardless of mode or state of RX/TX.? But the meter on my radio is in clear view so I don't really use the FLRIG meters. I don't know why they started showing up every time I run FLRIG.. I don't see any intuitive way to turn them off. I just click the x in the upper right of the meter box every time.
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

 

Okay so I sniffed the serial port between the PC and the radio while the SG was transmitting, and flrig does not appear to be sending any "RM;" commands to the radio, so it is basically not trying to read the meters.

I did verify that all the meters were checked in the Config -> Setup -> Polling menu.
Thanks
Eric


On Mon, 19 Aug 2024 at 10:24, Cliff via <ae5zaham=[email protected]> wrote:
Right, it sticks if you close flrig with it displayed, but if you close the dialog then close flrig it will not come up next time unless you go to config and request it again. At least that is the way it works here and should work.

73,
Cliff, AE5ZA



On Aug 19, 2024, at 09:16, Philip Rose via <gm3zza@...> wrote:

Cliff,

If you Save Prefs, the I am glad that it sticks. You either use it or you dont. Either way you want flrig to start each time the way you use it.

Phil GM3ZZA



On 19 August 2024, at 15:09, Cliff <ae5zaham@...> wrote:


Wayne,

The meters dialog is brought up with the Config/UI setting as in the screenshot below, however it is not a setting that should stick. Closing the dialog should close it and next time it should not come up on its own. You might have a corrupted configuration file. To test that go to C:\Users\<login-name>\flrig.files\ directory and rename the ts590sg.prefs file to something else and resetup the config. See if that makes any difference.


73,
Cliff, AE5ZA



On Aug 19, 2024, at 08:05, Wayne Carpenter KN2Z @minicowman via??<mwcarpe@...> wrote:

I have a very similar issue with my 590sg.. Only the S meter works on RX and PO works on TX.? SWR, ALC, whatever IDD is, and Volts all remain clear regardless of mode or state of RX/TX.? But the meter on my radio is in clear view so I don't really use the FLRIG meters. I don't know why they started showing up every time I run FLRIG.. I don't see any intuitive way to turn them off. I just click the x in the upper right of the meter box every time.
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

Cliff
 

¿ªÔÆÌåÓý

Right, it sticks if you close flrig with it displayed, but if you close the dialog then close flrig it will not come up next time unless you go to config and request it again. At least that is the way it works here and should work.

73,
Cliff, AE5ZA



On Aug 19, 2024, at 09:16, Philip Rose via <gm3zza@...> wrote:

Cliff,

If you Save Prefs, the I am glad that it sticks. You either use it or you dont. Either way you want flrig to start each time the way you use it.

Phil GM3ZZA



On 19 August 2024, at 15:09, Cliff <ae5zaham@...> wrote:


Wayne,

The meters dialog is brought up with the Config/UI setting as in the screenshot below, however it is not a setting that should stick. Closing the dialog should close it and next time it should not come up on its own. You might have a corrupted configuration file. To test that go to C:\Users\<login-name>\flrig.files\ directory and rename the ts590sg.prefs file to something else and resetup the config. See if that makes any difference.


73,
Cliff, AE5ZA



On Aug 19, 2024, at 08:05, Wayne Carpenter KN2Z @minicowman via??<mwcarpe@...> wrote:

I have a very similar issue with my 590sg.. Only the S meter works on RX and PO works on TX.? SWR, ALC, whatever IDD is, and Volts all remain clear regardless of mode or state of RX/TX.? But the meter on my radio is in clear view so I don't really use the FLRIG meters. I don't know why they started showing up every time I run FLRIG.. I don't see any intuitive way to turn them off. I just click the x in the upper right of the meter box every time.
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

 

Cliff,

If you Save Prefs, the I am glad that it sticks. You either use it or you dont. Either way you want flrig to start each time the way you use it.

Phil GM3ZZA



On 19 August 2024, at 15:09, Cliff <ae5zaham@...> wrote:


Wayne,

The meters dialog is brought up with the Config/UI setting as in the screenshot below, however it is not a setting that should stick. Closing the dialog should close it and next time it should not come up on its own. You might have a corrupted configuration file. To test that go to C:\Users\<login-name>\flrig.files\ directory and rename the ts590sg.prefs file to something else and resetup the config. See if that makes any difference.


73,
Cliff, AE5ZA



On Aug 19, 2024, at 08:05, Wayne Carpenter KN2Z @minicowman via <mwcarpe@...> wrote:

I have a very similar issue with my 590sg.. Only the S meter works on RX and PO works on TX.? SWR, ALC, whatever IDD is, and Volts all remain clear regardless of mode or state of RX/TX.? But the meter on my radio is in clear view so I don't really use the FLRIG meters. I don't know why they started showing up every time I run FLRIG.. I don't see any intuitive way to turn them off. I just click the x in the upper right of the meter box every time.
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

Cliff
 

¿ªÔÆÌåÓý

Wayne,

The meters dialog is brought up with the Config/UI setting as in the screenshot below, however it is not a setting that should stick. Closing the dialog should close it and next time it should not come up on its own. You might have a corrupted configuration file. To test that go to C:\Users\<login-name>\flrig.files\ directory and rename the ts590sg.prefs file to something else and resetup the config. See if that makes any difference.


73,
Cliff, AE5ZA



On Aug 19, 2024, at 08:05, Wayne Carpenter KN2Z @minicowman via <mwcarpe@...> wrote:

I have a very similar issue with my 590sg.. Only the S meter works on RX and PO works on TX.? SWR, ALC, whatever IDD is, and Volts all remain clear regardless of mode or state of RX/TX.? But the meter on my radio is in clear view so I don't really use the FLRIG meters. I don't know why they started showing up every time I run FLRIG.. I don't see any intuitive way to turn them off. I just click the x in the upper right of the meter box every time.
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

 

Hi Wayne,

Close the meters dialog. Hi to Config->UI->Configuration->Dave Prefs. The dialog shouldn't appear next time you start flrig.

IDD? is the PA current (drain current).

I use this dialog when I'm operating remote. I also use it when local as I don't usually have them all displayed on the IC7300 screen. I can only see two at a time, and in TX you need SWR, Power and ALC.

Phil GM3ZZA



On 19 August 2024, at 14:05, "Wayne Carpenter KN2Z @minicowman via groups.io" <mwcarpe@...> wrote:


I have a very similar issue with my 590sg.. Only the S meter works on RX and PO works on TX.? SWR, ALC, whatever IDD is, and Volts all remain clear regardless of mode or state of RX/TX.? But the meter on my radio is in clear view so I don't really use the FLRIG meters. I don't know why they started showing up every time I run FLRIG.. I don't see any intuitive way to turn them off. I just click the x in the upper right of the meter box every time.
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

 

I have a very similar issue with my 590sg.. Only the S meter works on RX and PO works on TX.? SWR, ALC, whatever IDD is, and Volts all remain clear regardless of mode or state of RX/TX.? But the meter on my radio is in clear view so I don't really use the FLRIG meters. I don't know why they started showing up every time I run FLRIG.. I don't see any intuitive way to turn them off. I just click the x in the upper right of the meter box every time.
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

 

Hi Cliff, I installed 05 and I'm seeing the same behavior. Po will display but SWR and ALC don't seem to be working.
Thanks
Eric


On Sun, 18 Aug 2024 at 22:13, Cliff via <ae5zaham=[email protected]> wrote:
Try the 2.0.05 version of flrig.

73,
Cliff, AE5ZA



On Aug 18, 2024, at 16:27, Eric Hidle via <eric.hidle@...> wrote:

I am running flrig 2.0.04 with a ts-590sg and it looks like flrig won't read/display the meters for SWR or ALC. I see Pout okay, but that's the only meter that seems to work. Is anyone else seeing this?
Thanks in advance
?
Re: FLDIGI & FT-991A Settings

 

¿ªÔÆÌåÓý

Try reversing the right/left channel



David

On 8/19/24 01:00, Howard wrote:

Hello Gabor,
?
Great information! This got me a lot closer to getting on the air. FLRIG? is now working, and FLDIGI will activate the transmitter. However, in CW mode, all I get is continuous tone, just like with the tuning button.
?
Any ideas on what might be causing that?
FLDIGI & FT-991A Settings

 

Hello Gabor,
?
Great information! This got me a lot closer to getting on the air. FLRIG? is now working, and FLDIGI will activate the transmitter. However, in CW mode, all I get is continuous tone, just like with the tuning button.
?
Any ideas on what might be causing that?
Re: FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

Cliff
 

¿ªÔÆÌåÓý

Try the 2.0.05 version of flrig.

73,
Cliff, AE5ZA



On Aug 18, 2024, at 16:27, Eric Hidle via <eric.hidle@...> wrote:

I am running flrig 2.0.04 with a ts-590sg and it looks like flrig won't read/display the meters for SWR or ALC. I see Pout okay, but that's the only meter that seems to work. Is anyone else seeing this?
Thanks in advance
?
FLRIG 2.0.04 + TS590SG, DSP Filter Selection in DATA while using "Lo/Hi" Mode

 

When using flrig 2.0.04 with my ts-590sg, if I have the radio set to use "Lo/Hi" filter mode instead of "Width/Shift" mode in the DATA mode, flrig does not seem to know how to handle this. Has anyone else observed this or can someone else confirm this behavior?
Thanks in advance!
FLRIG 2.0.04 + TS590SG, Meters Display no SWR or ALC

 

I am running flrig 2.0.04 with a ts-590sg and it looks like flrig won't read/display the meters for SWR or ALC. I see Pout okay, but that's the only meter that seems to work. Is anyone else seeing this?
Thanks in advance
?
1261 - 1280 of 38083