ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
esc to dismiss
cliff, to be clear, fldigi cq call keys the transmitter. The problem is that it is a constant tone during transmission. There is no diddledhen the transmitter is keyed.
73 Mike
Mike,
Sounds to me like a sound card issue. Not connecting on transmit. Maybe on wrong channel or need to put it on both channels??
What about other modes? Do they work ok on transmit?
On Oct 11, 2024, at 15:00, mike isakson via < w7xh.mike@...> wrote:
Don, if I try to send a cq , the transmitter is keyed but i get a constant carrier sound no dittle. I use flrig, fldigi and n3fjp and rig control is great, if I send rtty from the radio directly it decodes in fldigi. I will look at the link you provided. Thanks for your response. 73 W7XH
Mike
Are you getting PTT signal sent (radio should go into transmit mode)?
Are you putting out?any power (use power meter option on IC-7100)?
Initially I could receive?but not send also.
I found the following helpful and when I reset according to these instructions?all worked.:
Note: I had trouble with autobaud on CAT and a fixed setting of 19200 seems to have resolved this issue.
On Fri, Oct 11, 2024 at 10:53?AM mike isakson via ??<w7xh.mike= [email protected]> wrote: Call sign W7XH
I am hoping to ask the group about a problem I am having with my IC-7100 sending a continuous carrier . I do not get? a diddle. I have tried both 4.1.20 and 4.2.05 fldigi and flrig 1.4.2 and 2.0.05.
I? have installed IC 7100 usb drivers and am connected with a usb-a cable. The radio is set to RTTY . I have rig control with flrig,fldigi, and N3FJP operation. If I send a rtty message directly from the radio, fldigi decodes it perfectly. I am just not able to send.
73 Mike W7XH
--?
|
Your audio does mot?appear tp?be?getting to the IC-7100
1) make sure you have the correct sound card configured for output (speaker):? you need the IC-7100 usb so9und device
2) us this configuration?for IC-7100
-?
- you need to be on USB-D for the mode AND have the connectors configured to use USB for the sound?
When I followed the IC-7100 instructions o the web site everything worked/
On Fri, Oct 11, 2024 at 4:00?PM mike isakson via <w7xh.mike= [email protected]> wrote: Don, if I try to send a cq , the transmitter is keyed but i get a constant carrier sound no dittle. I use flrig, fldigi and n3fjp and rig control is great, if I send rtty from the radio directly it decodes in fldigi. I will look at the link you provided. Thanks for your response. 73 W7XH
Mike
Are you getting PTT signal sent (radio should go into transmit mode)?
Are you putting out?any power (use power meter option on IC-7100)?
Initially I could receive?but not send also.
I found the following helpful and when I reset according to these instructions?all worked.:
Note: I had trouble with autobaud on CAT and a fixed setting of 19200 seems to have resolved this issue.
On Fri, Oct 11, 2024 at 10:53?AM mike isakson via <w7xh.mike= [email protected]> wrote: Call sign W7XH
I am hoping
to ask the group about a problem I am having with my IC-7100 sending a
continuous carrier . I do not get? a diddle. I have tried both 4.1.20
and 4.2.05 fldigi and flrig 1.4.2 and 2.0.05.
I?
have installed IC 7100 usb drivers and am connected with a usb-a cable.
The radio is set to RTTY . I have rig control with flrig,fldigi, and
N3FJP operation. If I send a rtty message directly from the radio,
fldigi decodes it perfectly. I am just not able to send.
73 Mike W7XH
--
|
Mike,
Sounds to me like a sound card issue. Not connecting on transmit. Maybe on wrong channel or need to put it on both channels??
What about other modes? Do they work ok on transmit?
toggle quoted message
Show quoted text
On Oct 11, 2024, at 15:00, mike isakson via < w7xh.mike@...> wrote:
Don, if I try to send a cq , the transmitter is keyed but i get a constant carrier sound no dittle. I use flrig, fldigi and n3fjp and rig control is great, if I send rtty from the radio directly it decodes in fldigi. I will look at the link you provided. Thanks for your response. 73 W7XH
Mike
Are you getting PTT signal sent (radio should go into transmit mode)?
Are you putting out?any power (use power meter option on IC-7100)?
Initially I could receive?but not send also.
I found the following helpful and when I reset according to these instructions?all worked.:
Note: I had trouble with autobaud on CAT and a fixed setting of 19200 seems to have resolved this issue.
On Fri, Oct 11, 2024 at 10:53?AM mike isakson via ??<w7xh.mike= [email protected]> wrote: Call sign W7XH
I am hoping to ask the group about a problem I am having with my IC-7100 sending a continuous carrier . I do not get? a diddle. I have tried both 4.1.20 and 4.2.05 fldigi and flrig 1.4.2 and 2.0.05.
I? have installed IC 7100 usb drivers and am connected with a usb-a cable. The radio is set to RTTY . I have rig control with flrig,fldigi, and N3FJP operation. If I send a rtty message directly from the radio, fldigi decodes it perfectly. I am just not able to send.
73 Mike W7XH
--?
|
Don, if I try to send a cq , the transmitter is keyed but i get a constant carrier sound no dittle. I use flrig, fldigi and n3fjp and rig control is great, if I send rtty from the radio directly it decodes in fldigi. I will look at the link you provided. Thanks for your response. 73 W7XH
Mike
Are you getting PTT signal sent (radio should go into transmit mode)?
Are you putting out?any power (use power meter option on IC-7100)?
Initially I could receive?but not send also.
I found the following helpful and when I reset according to these instructions?all worked.:
Note: I had trouble with autobaud on CAT and a fixed setting of 19200 seems to have resolved this issue.
On Fri, Oct 11, 2024 at 10:53?AM mike isakson via <w7xh.mike= [email protected]> wrote: Call sign W7XH
I am hoping
to ask the group about a problem I am having with my IC-7100 sending a
continuous carrier . I do not get? a diddle. I have tried both 4.1.20
and 4.2.05 fldigi and flrig 1.4.2 and 2.0.05.
I?
have installed IC 7100 usb drivers and am connected with a usb-a cable.
The radio is set to RTTY . I have rig control with flrig,fldigi, and
N3FJP operation. If I send a rtty message directly from the radio,
fldigi decodes it perfectly. I am just not able to send.
73 Mike W7XH
--
|
Are you getting PTT signal sent (radio should go into transmit mode)?
Are you putting out?any power (use power meter option on IC-7100)?
Initially I could receive?but not send also.
I found the following helpful and when I reset according to these instructions?all worked.:
Note: I had trouble with autobaud on CAT and a fixed setting of 19200 seems to have resolved this issue.
On Fri, Oct 11, 2024 at 10:53?AM mike isakson via <w7xh.mike= [email protected]> wrote: Call sign W7XH
I am hoping
to ask the group about a problem I am having with my IC-7100 sending a
continuous carrier . I do not get? a diddle. I have tried both 4.1.20
and 4.2.05 fldigi and flrig 1.4.2 and 2.0.05.
I?
have installed IC 7100 usb drivers and am connected with a usb-a cable.
The radio is set to RTTY . I have rig control with flrig,fldigi, and
N3FJP operation. If I send a rtty message directly from the radio,
fldigi decodes it perfectly. I am just not able to send.
73 Mike W7XH
|
Index of /files/fldigi
and at
Refer to readme.txt for list of changes since 4.2.05.
73, David
W1HKJ
|
Call sign W7XH
I am hoping
to ask the group about a problem I am having with my IC-7100 sending a
continuous carrier . I do not get? a diddle. I have tried both 4.1.20
and 4.2.05 fldigi and flrig 1.4.2 and 2.0.05.
I?
have installed IC 7100 usb drivers and am connected with a usb-a cable.
The radio is set to RTTY . I have rig control with flrig,fldigi, and
N3FJP operation. If I send a rtty message directly from the radio,
fldigi decodes it perfectly. I am just not able to send.
73 Mike W7XH
|
flrig development version 2.0.05.77 posted at
Index of /alpha/flrigs
Tested with Icom 7300 and QRP L:abs QMX+ transceivers.
73, David,
W1HKJ
|
RRI Bulletin & Winlink Request
Hello Everyone:
Please see the following request from the Winlink programs group and the Radio Relay International bulletin issued earlier today:
-------- Forwarded Message --------Thank you Scott! And, yes, we need to keep a clear Part 97.221(b) for any individual or agency needing to use Winlink for EmComm on our US Ham bands.?
Specifically:? 28.120-28.189 MHz,? 24.925-24.930 MHz,? 21.090-21.100 MHz,? 18.105-18.110 MHz,? 14.0950-14.0995 MHz, 14.1005-14.112 MHz,? 10.140-10.150 MHz,? 7.100-7.105 MHz,? 3.585-3.600 MHz?
Considering that our occupied bandwidth for protocols used is between 2.3KHz and 2.75 KHz, and that we share these segments with others, we don¡¯t have much wriggle room!
Lastly, a US end-user may also use RMS gateways from other countries that will appear outside these segments since they are present as a control operator (not under automatic control). This would include the RMS gateways in Canada, Mexico, ITU sponsored gateways in Central America and the Caribbean.
FYI,
Steve, k4cjx
¡ª¡ª¡ª¡ª¡ª¡ª¡ª¡ª
Also, here is a link to today¡¯s Radio Relay International Bulletin issued at 1945Z.
| |
Thank you,
James Wades (WB8SIW)
Emergency Management Director
Radio Relay International
325 East Front St.
Suite 115
Buchanan, MI. ?49107
www.radiorelay.org
Re: Which versions are best for my older system.
I believe the setup file checks to see wheth3er you have 64 or 32-bit Windows. I have 64-bit Windows 10 and the install folder is in "Program Files" rather than "Program Files (X386).
?
However Flamp and Flmsg are in the latter folder.
|
Re: Which versions are best for my older system.
Thanks for the info on 4.2.05.
That IS newer than mine.
|
Re: Which versions are best for my older system.
Hello 'DDT' / 'remington308',
I've been using FLdigi extensively on my Win7 32 bit laptop, and it works just fine and stable.
Since you have FLdigi already installed, I recommend you use the FLdigi 'Help - Check for updates' function, or, if you prefer, 'Help - FLdigi website', which will take you to 'http://www.w1hkj.com/Fldigi.html'. From there, you'll find links to the respective download sites. Be sure to use the old-school 'http:', not 'https:', which we've learned leads astray!
The latest published 'stable' release which I've been using much of the year (since it was published in April) is fldigi ver4.2.05.
If you try downloading the setup file 'fldigi-4.2.05_setup.exe' manually for sourceforge, instead of using the prominent green 'Download' button (which usually points to the latest uploaded component but not FLdigi itself), be sure to go to the 'files' section and select the latest stable release directly.
The same applies if you need any component, e.g. FLamp, FLmsg etc.
I don't think there are any separate 64 bit versions, the common Windows setup file mentioned above has always worked for me (32 bit Win7 OS).
Good luck!
73s SWL Tobias
.-.-. Am Montag, 7. Oktober 2024 um 22:30:45 MESZ hat DDT via groups.io <remington308@...> Folgendes geschrieben:
Computer is a Win 7 home premium, 32 bit laptop, (won't accept 64 bit, OR later windows versions.) Radio is a Yaesu FT-991A It already has the control files for remote installed I only need Fldigi and Flrig versions. Please include source location.
I DO have older versions already installed, (from 2021) (Haven't been on in quite a while and never did get things working all the way for remote control before having to lay off for a while!)
I don't want to have to update the computer, because it is a "military hardened" one that can take beating that would kill most laptops and still work; like 10 G impacts, (metal cased too,) and EMP shielded.
|
Which versions are best for my older system.
Computer is a Win 7 home premium, 32 bit laptop, (won't accept 64 bit, OR later windows versions.) Radio is a Yaesu FT-991A It already has the control files for remote installed I only need Fldigi and Flrig versions. Please include source location.
I DO have older versions already installed, (from 2021) (Haven't been on in quite a while and never did get things working all the way for remote control before having to lay off for a while!)
I don't want to have to update the computer, because it is a "military hardened" one that can take beating that would kill most laptops and still work; like 10 G impacts, (metal cased too,) and EMP shielded.
|
Re: Hand keying into fldigi
I think his point is to be able to hand key WITHIN the weak signal capability of fldigi. That, coupled within the simplicity and weak signal of CW itself should be a boon to DX.
--
73
Karl
KI4ZUQ
|
Re: Hand keying into fldigi
I'm curious.. Have you simply connected your key to your radio?? I'm running a KW TS-590sg with both a straight key and a set of paddles connected directly to it. I also run fldigi to send repetitive content or during contests but just go directly to the key/paddles which bypasses all the fldigi stuff.
|
is this easy to do, I worked the URC=dx rty contest, but it is not in fldigi.? I had to use n1mm, and was wondering why exchanges were incorrect, and had to fix several
?
3 letter code, not cq zone, or state abreviation
?
? ?for more info, if needed
?
?
|
Re: Hand keying into fldigi
What method are you using to key the radio? Are you using the DTR/CTS method with your USB/RS232 adapter? If so, you need to connect your straight key to the correct pin on the RS232 connector so that it applies the correct signal (ground or high) to the input on your radio and set that method up in Fldigi.
?
Nate? N2ADD
|
Re: FLDIGI/FLRIG use as a stand-alone contest log for CQWW-RTTY --- where are the fields?
Ah, I see! I went back to double check this, and here is what I am seeing. I'm using Fldigi 4.2.05.24 and I have the 'CQ WW DX RTTY' contest selected.?
?
When I click on the callsign in the RX window (K4RVA), it is automatically filling the CQz field with a '5', which would normally be correct for a K4 callsign, however I live in Colorado, which is in CQ zone 4.
?
If I click on '04' in the RX window, it does not transfer to the CQz field, I assume because there is already something there. But if I remove the '5' from the CQz field, and then click '04' in the RX window, it does populate the CQz field with '04'.
?
Clicking on 'CO' transfers it to the CQs field, as expected.?
?
?
I looked around, but did not find anywhere to disable or override the automatic population of the CQz field. I do not have data base lookup enabled in Config > Call > Lookup.?
?
?
|
I have been using fldigi for CW - that works fine for decoding and sending from the keyboard.? But I would like to introduce hand keying through my USB/RS232 adapter but am unable to get it to work.? In fact I have been unable to get fldigi to see my hand key at all.? So what am I doing wrong?? Any advice would be appreciated.? I have got a feeling that it is most likely the case I have not been able to see the wood for the trees.? (User error).
73
Bob VP8LP
|
Re: FLDIGI/FLRIG use as a stand-alone contest log for CQWW-RTTY --- where are the fields?
Rick:
Many thanks for your help with this.
As is usually the case, this was clearly a case of my own "operator error"! I'll have to do another one, and see how I can duplicate your example.
THANKS TO ALL WHO MAY HAVE READ MY REQUEST.
73,
Bill K2TNO
Hi..
I have just tried this with Fldigi and it works correctly for me.
I did not setup the outgoing exchange but I have included 2 screen
shot. When I click on the call it is transfered to the call window
clicking on the zone goes to the CQz window and clicking on the
state goes to the CQs. It works like it is supposed to..
73 Rick N2AMG
On 10/3/2024 1:10 PM, William Schrader
wrote:
STEVE:
Thanks... I
hope there is another?answer, since I dont?favor having to
manually edit every contact?in a Cabrillo file!??
But, I am
glad to hear that at least I am not just crazy by not getting
this to work right off the bat. I'll keep waiting to see what
others have to say...
73
Bill K2TNO
On Wed, Oct 2, 2024 at 09:38 AM, William Schrader wrote:
So, when I call a station and he sends "K2TNO 599 14
14 K2TNO" --- if I cick on the "14" it didnt
automatically go into the "CQr" field.
More importantly, if the contact sent me "K2TNO 599
03 WA 03 WA K2TNO'--- what was I supposed to click on to
get their Zone into the "CQr" field, and what was I
supposed to do with the "WA" state info??
?
Hi Bill, I just tried this with Fldigi 4.2.05.24 and I got
the same results that you did. I don't know if the contest
exchange was changed after this contest was added to Fldigi?
?
Usually I will use 'Generic Contest' in Fldigi for
everything, which will capture anything I click on to the
"Xch" field, and then I edit the Cabrilo file manually to
match what is required for a particular contest.?
?
Steve K4RVA
|
Dave
Karl
Wayne Carpenter KN2Z @minicowman
Steve K4RVA
