开云体育

Thank you! -- Bob Jacobsen rgj1927@...

Figured it out by reading some older messages. I added the 'Report' to 'toReportString()'? and removed the 'toString()' later in the script. Probably obvious to you code gurus but took me a bit to

Paul, I did some experimentation and believe I have found a solution, or at least what I want to happen is now happening ;-). I was running a script with an error in it at startup (topic 167239).

Thank you for the info Inobu.? The dispatcher will have control over the whole railroad mainline. Thank you, Frank

Thank you Ken.? I'll have to process this for a bit to see how I am going to do this.? I loosely laid it out on a piece of paper to see what I was dealing with.? Yes, about 8-10 are crossovers and

Frank, The panel I mentioned was 50 some odd switched. Trying to get them on one panel wasn't hard. The issue was managing the panels operation.? It is easier to pull up say.... a Fresno and

Frank, What I've done is created thinner versions of the normal screen parts, but many times I've used thin fillers between the normal parts to give a little space for fingers and the diagram above

*From Tony's Train exchange Special Application Notes* For BLI Switchers and Proto GP9: We found that sometimes a 12 Ohm 1 Watt resistor (Digikey P12W-1BK-ND or equivalent) placed *between the

Hi Guys, What is the best way to PLAN the CTC panel?? Meaning, how much space to allow for the turnout/signal icons on the panel?? I'm using two 22" monitors and want to make sure to have enough

Hi Bill It should just work. Is this a point to point or around and around? If it continious make sure theres a delay, I do know that can be an issue. If you make the file load on startup does it

i was using 2 19 inch monitors for a long time but the big black area between the 2 was very distracting. Then I discovered a samsung untried wide. I did not have to do anything more than just

Yes, I did a huge one a few years ago and it spanned across 2 27" monitor. It was hard to manage so I ended up breaking it down into separate areas. You want to divide the windows up so you can have

Thanks Inobu.? I changed the PrivateMounts from 'yes' to 'no' and it didn't work.? I'm going to try to install an earlier OS than Buster and install JMRI manually to see if it works.? Will report

Frank, I have a JMRI panel that spreads across 2 monitors, and have seen panels on 3 wide monitors. As long as you have setup your monitors to extend from one to the next as one wide window, then it

Hello, I'm not exactly sure how to ask the question, so here is basically what I want to do: I'd like to create a dispatcher panel in Panel Editor and have it flow across two monitors.?

You could always try Blast Mode for programming a sound decoder: https://dccwiki.com/Digitrax_Zephyr_OPS_Mode_Decoder_Programming Be aware that you will be using Ops Mode, so no other locomotive

You don't "upgrade" JMRI when using Linux or macOS. You delete or rename the existing install and then expand the new download. Assuming that you have downloaded the 4.18 file and moved it to the

Raspberry Pi 3B+ , Raspbian flavour Buster, Java v 11.05 , system current ( no outstanding upgrades or removals required). I can not get the upgrade to take either 4.17 nor 4.18 using xarchiver

I ‘suspect’ the recommendation was for a 1,000 ohm resistor. Possibly a typo. This is a ‘common’ solution for programming Lenz, and Lenz manufactured OEM non-sound decoders on a DCS50. The

SoundValue decoders are based on the first gen? Tsunami decoders and all Digitrax systems had problems programing them. The addition of a Soundtraxx PTB-100 was suggested. One work around with the