开云体育

Hi Dave, As I stated in an earlier reply, I closed any AV's, etc and did a clean install. Sorry to disagree about the registry, but there are lots of JMRI file/entries in the registry, all of which I

Dave, ? Thanks for your response. ? To clarify, is thetimeout due to the NCE command station or to JMRI? ? It is interestingto me that JMRI ran well for the 3 hours to the end of the OS after I

I suspect there may be some users who do not create and load a panel file to preserve the turnouts (and user names if created). LocoNet for example will learn the turnouts from many of the devices

Steve, I will be at the club tomorrow showing off the layout to visitors and will get what you asked for below. David Klemm Sent from my iPhone 8 Plus ________________________________ Sent: Friday,

All, The "Show Only Turnouts with Usernames" predates the filter and selection logic now available in the WiThrottle window on the JMRI side. It remains in place to keep existing setups working the

Ken/Robin, Is the behavior I am seeing the new normal? In other words do I need to add names? And if so can it be done from the window in WiThrottle menu or is it done elsewhere? David Klemm Sent from

David, I just checked on older JMRI 4.7 and 4.8 and I can check Turnouts in the JMRI WiThrottle Turnouts Filter screen whether or not they have User Names. The ones that lack User Names do not show up

Digitraxs PR3 changes the sound cv of soundtrax decoders to one or zero when you try to run them with the PR3 I assume you have a DCS other than the PR3. Use that with the PTB100 and your problems are

Hi! I am having issues with JMRI. It is Win 10 & a PR4. Win 10 is the latest version. Java is at the latest release. It started today. When I go to program an Engine, it starts to write CV1, then I

GeoffB, It is too bad your system is a rare one in the world. It isn't one I've had much contact with and what I've gathered is the JMRI interaction is minimal due to limited response or interest from

Ken, Not in front of he PC but there were 3 choices, select all, unselect all and select user names. So it seems like select all should be regardless if they have a user name. David Klemm Sent from my

David, I think the current software filters out turnouts without user names. Since many times the un-named turnouts are things like signal lamps and unused turnouts. I think it will be an option in

JMRI doesn't use the registry. The NSIS installer would make an entry in the installed programs list. You need to disable your virus protection while installing it. Make sure you get a good download

Robin, None of he buttons work and nothing shows in system console. I save the panel and restart and nothing is showing. David Klemm Sent from my iPhone 8 Plus _____________________________ Sent:

Hello Ken, Yes, as I said in a reply to Dave, I have completely uninstalled everything jmri - and gone completely through the registry. The Java is the latest one. When I installed the jmri, it goes

Hello, I I am having a sound issue with decoder pro. I’m using Windows 7, the very latest version of JM all right to go to pro, DigiTrax PR3, & a Ptb100. I’ve tried this with three brand new

David, If you open WiThrottle=>Routes & Turnouts and then select the Turnouts tab, you will see 3 buttons at the bottom. When you click "Include All" all of the turnouts should get checked. I'm

Robin, I was only checking the preferences for a WiThrottle. In the window under the menu WiThrottle I went to Routes & Turnouts. I opened that and no turnouts were checked. I have tried to get them

Robin, So to recap. Only tested with iPhones as no ones with an Android has been around when I am here. I only get User TO and a handful of turnouts instead of our hundred. I checked preferences under

Ok.. I'll do that, I'm not near the setup right now. It does appear that it might be the whole of JMRI is slowing down and it's the route selection that shows it the clearest.