Hi Dave
Great to hear from you again.?
Thanks for looking through and commenting on P2a12b. I shall put that right. Regarding Sensors, again your comment is correct. I changed strategy as can be seen in the North ladder turnouts, Sensors are taught to the Servo modules and I standardised on those turnouts in the North Ladder to use events 10 upwards, in pairs, for each servo to avoid any potential clash with servo and Sensor events (each module can have a maximum of 8 Servos attached). This is part update I planned to carry out when I resolved the P9/10 issue.
I also discovered that I did not have a proper handle on assigning the A and B turnouts. This I found when I built up the two slips in the North Ladder. When I first assigned them to these Slips, I took the end with the 'blue connector as being the 'A' turnout and it resulted in problems when testing. I reversed the assignment in the slip Edit Dialog and this cleared the problem. I had in mind to change P2a/1b and will also do that now.
I am looking forward to completing the layout panel and then I shall start to implement the signalling that you tutored me on.?
Perhaps Steve will help me with the North Ladder Slip.?
Best wishes
Peter

开云体育

you are screwed as far as decoder pro is concerned most likely.

开云体育

Jan, All I am indicating is what dug up in the TCS decoder manuals regarding Hysteresis (or hysterasis)?? as it applies to the WOW decoder as I believe this is were the question came up from.? The thread had no mention of "hysteresis" in it until? Paul threw it out there.? So I assumed it had to be TCS WOW related.

The proper spelling is HYSTERESIS.? The typo is in the WOW decoder manual and throws a curve when one is searching for the proper definition/use of HYSTERESIS as it applies to the WOW decoder.

It is a SOUND related setting? that? takes it? value from BEMF.. The default value = 80.. so a difference (either - or + ) of 80? will increase? or decrease? the current notch rate.? That is how the TCS WOW manual
seems to describe the " HYSTERESIS "? (or HYSTERASIS? if you look in WOW manual) .? And as I stated, it only applies to one Throttle? mode, Prototype throttle mode, auto notch.

TCS video on? Throttle modes :?? .? Unfortunately, no mention of hysteresis in it?

Marc?

开云体育

Hi
I'm developing a fictitious layout in Layout Editor with twin track, with many twists and turns, such that it's difficult to follow which track is which. To help with this I've started using the Track Drawing Options to colour the different tracks. To do this I've assigned one of the tracks as mainline, and the other sideline and given then used different ballast colours. This is reflected on the model also.

This is great on the 'native' panel, but when shown on the web no colouring is present. I'm guessing that this in on a to-do list somewhere, but was wondering if it's planned for implementation in the near future, or whether I should use a different approach to highlighting the differences?

Here's a somewhat colourful example of the colouring that can be done, along with it's web representation: /g/jmriusers/files/ProblemsBeingWorkedOn/Andy%20Brown%20-%20161045//TrackDrawingOptionsWeb01.pdf

I'm currently using JMRI v4.17.6

Thanks
Andy

Files moved to:
/g/jmriusers/files/ProblemsBeingWorkedOn/peter.s.drury

--
Peter Ulvestad

JMRI Users Group Moderator - ( )
Tam Valley Group Moderator - ( )
Sprog-DCC Group Moderator - ( )
Edmonton Model Railroad Association -

This is a place for temp files, other than administrative files.
Either they are to be added to the next release, added to the Documents
or will have a short life span.

Groups.io has free subscription storage limit of 1 GB!
The following are counted towards the storage limits for the group:
- Files
- Photos
- Images in databases
- Images in wiki pages
- Message attachments

1. Please put files into the correct folders.
- If there is not an appropriate folder, feel free to create one.

2. If you are working on a problem and want to load info for others to look at,
create a folder within the 'Problems Being Worked On' folder using the Msg number
or you name as the folder name. When the problem is resolved please delete the folder.

3. All files and photos are subject to removal at the moderators discretion.

Your Moderators
--
Peter Ulvestad

JMRI Users Group Moderator - ( )
Tam Valley Group Moderator - ( )
Sprog-DCC Group Moderator - ( )
Edmonton Model Railroad Association -

I am having problems with two Double Slips - P2a/1b and P10/9. I have carried out checks on P10/9 it down to the Layout editor to map where the problem potentially lies and have narrowed the Layout Editor. Please find the pictures describing this at?/g/jmriusers/album?id=231878.
The panel is in the background, The Turnout Table is at the top with only the turnouts of interest visible. Below and to the left is the MERG FCU showing the received messages on CBUS and the fial window is the MERG CBUS Console.
I have posted the events as they progresed through the check. The first image describes how I set the Double Slip - both P10 and P9 in the Closed condition (Branch to Platform 3.) At every stage I checked the physical state on the layout and confirmed that this, and the messages, conformed with my expectations (Note: I did add two sensors to P9? to check if there was any quirk.As can be seen, and from I described above, P9 is not acting as it should.
Just for the record, I have made extensive changes having previously set the turnouts to Internal addresses and converted these to MERG Node addresses. These changes may have caused problems within JMRI. I also realise that I need to tidy up to create a consistent approah throughout.
My current panel file can be found here.?
Thanks for reading?
Peter

Hello,

This email message is a notification to let you know that the following files have been uploaded to the Files area of the [email protected] group.

• /Dale Junction version 081219/Dale Junction 081219.xml

Uploaded By: peter.s.drury <peter.s.drury@...>

Cheers,
The Groups.io Team

Hello,

This email message is a notification to let you know that the following files have been uploaded to the Files area of the [email protected] group.

• /Dale Junction 081219.xml

Uploaded By: peter.s.drury <peter.s.drury@...>

Cheers,
The Groups.io Team

Guys:

There are issues where the sound volume resets on power up... read even a spot of dirty track... Check the instructions/drawings to be sure there isn't a pot buried in the locomotive to set the volume... Ask me how I know...

Jim Albanowski

开云体育

开云体育

Thanks guys! So for speed matching, I’ll set it to 0 and probably keep it at zero unless I consist it with other TCS equipped locos.

Paul

Sent via iPhone

I’m in the same camp as Bob. I have an MTH F7. I like the sound a lot and don’t want to replace ?the decoder. I’ve been able to program the address With JMRI, but nothing else. The volume control on the locomotive doesn’t work. It’s either on or off. The loco is too loud for my small room so I rarely use it, although it runs and sounds great! ?Any programming advice?

Hi all! I've been a long time Sprog user and joined to answer this question that has been driving me crazy. In JMRI, select SPROG Programmer from the menu and select Sprog Console. Under "Configuration", find SPROG Throttle Speed Step Mode. Click on 128 step (it may already be selected) and click on Apply.

Hope that helps someone!

Scott

On Sat, Dec 7, 2019 at 09:02 AM, <tom@...> wrote:

Anyone know why part of my layout is missing in display mode, but shows up in edit mode?

Not yet, but either posting the panel in ProblemsBeingWorkedOn with an appropriate folder (and name), or some more information might help.?

Track can be given a property of Hidden and only show up in Edit mode which is probably what is occurring.

Phil in gorgeous Young Harris, Georgia, USA

开云体育