开云体育

Can you add turnout position feedback to your system? This would require more wiring and some way to input this information to JMRI (I don't know enough about NCE hardware to advise on that, I'm using LCC for this sort of thing). Then send your signal command after receiving this feed back.

It may seem a bit of a bother, but it would avoid this problem, and it is how the prototype does it. :)

Tim Rumph
Lancaster, SC

Been there, done that with multi-address accessory decoders. Commands overflow in decoders.

Your analysis is basically correct.

But I don't know how to do delays with JMRI.
--
Dave in Australia

See below:

On 8 Nov 2018, at 1:01 AM, Ken Cameron <kcameron@...> wrote:

But here Dave and I differ, he is saying go back to 9600 and keep the items
addressed as was.

That wasn't what I was saying. I was saying to move the AIUs to 8 and 9, which Richard has done, but forget about moving the NCE USB for now, because there are more things that can go wrong with that, as has happened.

I say go with 19,200 and move things to the higher
addresses. I say that because one of your messages point to adding more AIU
boards later. So I'm going with the make the cleanup now while you have
fewer things. It is your choice.

Again, my suggestion is to clean up the AIU addressing and leave the NCE USB until later. You seem to believe the two are tied together. I have seen no evidence that they are.

I'll do some more testing tomorrow. I have no AIU but I do have a Mini Panel I can experiment with.

Also I'd remove the Startup action of loading the panel until you get the
baud rate matching and happy between the computer and the interface.
Otherwise you get extra errors about the interface not matching the panel
file you are loading.

I did suggest that as well. If the panel is loading at startup, that will most likely stop Richard from using Configure USB.

I'd say the only thing you missed was the step of putting the jumpers back
on when switching the baud rate. You could go back to that step of the plan
and work from there.

Ken, you missed the vital point that Richard doesn't have the jumpers any more. He vaguely remembers taking something off when he bought the USB but has no idea where they are.

Let's get my plan perfectly clear.
1) Unplug the two AIUs.
2) Don't put any jumpers on the NCE USB.
3) Take the JMRI settings back to:
-- System manufacturer: NCE
-- System connection: NCE USB
-- Serial port: COM4
-- USB version: V7.x.x
-- System: PowerCab
-- Additional Connection Settings checkbox ON
--- Baud rate: 9600.

4) Save and quit JMRI.
5) Turn off and restart Power Cab
6) Start JMRI and look for the V7.3.0 response in the log.
7) If all is well, check Preferences->Defaults to make sure all are set to NCE.
8) See if Show Cabs works now (may need a couple of refreshes to see Pro Cab at 2 and USB at 3.)
9) Plug in one AIU, refresh Show Cabs a couple of times and look for that AIU to appear.
10) Plug in the other AIU, refresh Show Cabs a couple of times and look for that AIU to also appear.
11) If all is well so far, then try changing AIU Switches as I suggested, one at a time, shutting down both JMRI and the Power Cab and restarting after a change is made.

- Note that I made no mention of removing panel from startup. Looking for a non-existent AIU on a Power Cab doesn't cause any errors.

AIU DIP switches:
- AIU 8 is Switch 4 Off, all others On.
- AIU 9 is Switches 1 and 4 Off, all others On.

Dave

Hi
I have bought one ESU Mobile Control II and installed Engine Driver in it.

I have set function 2 to be latching and I get a long whistle or horn sound when I use the function button on the screen.

I have also set the upper left button to function 2, but I can't get a long signal when I use the side button to activate the whistle/horn. It only gives me a short signal. I can't find anything in the settings to change this.

Is it a bug, is it supposed to work this way or have I missed something?

Best regards
Roland Levin

The link has a space in it, which might not come through certain email setups. See this page:



for links or try:




Bob

On Nov 7, 2018, at 6:38 AM, Gary Ray <gerber1926@...> wrote:

Seems to be a dead link.

Gary Ray

From: [email protected] [mailto:[email protected]] On Behalf Of Paul Davidson
Sent: Tuesday, November 6, 2018 9:27 PM
To: [email protected]
Subject: Re: [jmriusers] JMRI starter tutorial

Try this link. It is a power point presentation on using OperationsPro
www.bhamrails.info/Model_Railroading/New Layout/Operations/JMRI Ops.
Paul D

Virus-free. www.avast.com

--
Bob Jacobsen
rgj1927@...

I was also in the same boat and found a couple of handouts like Geralds’ very valuable. If you have access to YouTube, search ‘JMRI Operations’. There are numerous videos that will lead you through it. I’d also do a lot of playing with the demo files that come with the Operations software. The learning curve can be steep ( and occasionally the frustration level) but you can make it do almost anything you need.

开云体育

开云体育

开云体育

Richard,

Yes those 8 pins, 2 rows of 4, are the jumpers. As you said, those are where
you removed them when you first got the unit. Putting them back will give
you the 19,200 baud rate.

But here Dave and I differ, he is saying go back to 9600 and keep the items
addressed as was. I say go with 19,200 and move things to the higher
addresses. I say that because one of your messages point to adding more AIU
boards later. So I'm going with the make the cleanup now while you have
fewer things. It is your choice.

Also I'd remove the Startup action of loading the panel until you get the
baud rate matching and happy between the computer and the interface.
Otherwise you get extra errors about the interface not matching the panel
file you are loading.

I'd say the only thing you missed was the step of putting the jumpers back
on when switching the baud rate. You could go back to that step of the plan
and work from there.

-Ken Cameron, Member JMRI Dev Team
www.jmri.org
www.fingerlakeslivesteamers.org
www.cnymod.com
www.syracusemodelrr.org

Don't let it get you down, you are making progress, it's always a learning process. I too have been overwhelmed. I took a six year hiatus due to 'health' reasons, and have found that 'Raspberry Pi and Arduino" is just a big mystery to me. Bought an arduino kit and now understand that you can make just about anything. It would help if users said 'my arduino crossing gates", but I can't even consider this part of the hobby at this time.. Take small steps, walk away for a while, have a beverage or three and try again slowly in the morning. We have all been where you are now, keep your chin up and your mouth closed in case there are birds.

See below:

On 7 Nov 2018, at 9:16 PM, Richard_vanRaay via Groups.Io <richard_vanraay@...> wrote:

Wouter gave me a great link Tina photo of the USB interface but for the life of me I can't find the Jumpers on it! He gave a link to Tony's Trains.
When I study mine under a magnifying glass I am still unable to see anything that looks like it can be switched.
There are little black boxes with numbers like 271.
Is it the 8 pins that stick up that I believe I took a plastic case off when I bought it? It says SETUP right next to it. It is next to the LED near the curly cord.

Yes, it is the 8 pins in two rows between SETUP and 1 2 3 4. But don't worry. Simply leave them all bare.

Then JMRI preferences are:
-- System manufacturer: NCE
-- System connection: NCE USB
-- Serial port: COM4
-- USB version: V7.x.x
-- System: PowerCab
-- Additional Connection Settings checkbox ON
--- Baud rate: 9600.

Save and quit JMRI.
Turn off and restart Power Cab
Start JMRI.

The JMRI console log should then report V7.3.0.

I AIU,have theset the AIU's to 8 and 9

Good

WiThrottle is working.

Good

NCE show cabs keeps coming up error.

Don't know why. It works for me with JMRI V4.13.4 and the settings above.

All preference Defaults are NCE

Check them again after making changes.

Tell us if any LEDs are stuck ON on the NCE USB. They should not.

Post a Console Log and Ken can look over it while I try to get some sleep...

Dave

NCE PowerCab with USB, JMRI 4.12, Java 1.8.1, UK equipment mixed Cobalt and Guagemaster Turnout motors, Train Tech signals,

I have a Layout Panel which does what is expected "on the screen" and the correct NCE commands are sent out (i.e. the turnouts and signals change state on the screen and the JMRI NCE Command Monitor reflects the commands I would expect to appear.? However it all happens in a rush.? At times turnout operations get missed out ON THE LAYOUT - i.e the commands are there but somehow they overrun each other or "get lost" in the traffic (I think power draw on the accessory bus is also a factor). Also signals change before turnouts have completed their movements (a no-no in 12" to the foot terms). I had a similar experience when I automated my system using NCE Mini-panels.? In that case (despite arguments from many that it should not be necessary) I programmed delays into the panel logic to ensure time between key changes, and that all turnouts could complete before the command to change a signal was issued.

I have searched JMRI documentation and this forum and can find nothing to help me - probably because I don't know how to put the question to the search engines.

Can anybody help please?

Iain,
Newcastle upon Tyne, UK

Wouter gave me a great link Tina photo of the USB interface but for the life of me I can't find the Jumpers on it! He gave a link to Tony's Trains.
When I study mine under a magnifying glass I am still unable to see anything that looks like it can be switched.
There are little black boxes with numbers like 271.?
Is it the 8 pins that stick up that I believe I took a plastic case off when I bought it? It says SETUP right next to it. It is next to the LED near the curly cord.
I? AIU,have theset the AIU's to 8 and 9
WiThrottle is working.
NCE show cabs keeps coming up error.
Baud rate is 9600
All preference Defaults are NCE

The COM port isn't bad according to the log you posted. You are just missing those jumpers.

I suggest you forget about changing the address of the NCE USB. Take all jumpers off, change baud rate back to 9600 and it should all start working again, WiThrottle, Show Cabs, etc.

If not, check Preferences->Defaults and make sure everything is set to NCE and nothing to Internal.

Then please try changing the AIUs to 8 and 9 using the DIP switches:
- AIU 8 is Switch 4 Off, all others On.
- AIU 9 is Switches 1 and 4 Off, all others On.

Check for changes in Show Cabs.
--
Dave in Australia

The * in V7.3.* is the jumpers. You have to put jumpers 2,3,4 onto the pin pairs of the NCE USB.

See my earlier setup instructions.
--
Dave in Australia

Now the WiThrottle is working but back to a bad com port on the laptop. All firewalls are off. I need the laptop now only to send information to this group .
I will reconnect to the Raspberry Pi after I send the lates console report.

2018-11-07 19:48:35,846 util.Log4JUtil??????????????????????? INFO? - * JMRI log ** [main]
2018-11-07 19:48:35,861 util.Log4JUtil??????????????????????? INFO? - This log is appended to file: C:\Users\Toshiba laptop\JMRI\log\messages.log [main]
2018-11-07 19:48:35,863 util.Log4JUtil??????????????????????? INFO? - This log is stored in file: C:\Users\Toshiba laptop\JMRI\log\session.log [main]
2018-11-07 19:48:35,878 apps.Apps???????????????????????????? INFO? - PanelPro version 4.12+Rb6a9bb1 starts under Java 1.8.0_151 on Windows Vista x86 v6.0 at Wed Nov 07 19:48:35 AEDT 2018 [main]
2018-11-07 19:48:37,004 apps.Apps???????????????????????????? INFO? - Starting with profile My_JMRI_Railroad.3f558d63 [main]
2018-11-07 19:48:37,584 node.NodeIdentity???????????????????? INFO? - Using jmri-dNQe-cAGbhNiaaacjEYECc-3f558d63 as the JMRI Node identity [AWT-EventQueue-0]
2018-11-07 19:48:38,323 xml.AbstractSerialConnectionConfigXml INFO? - Starting to connect for "NCE" [main]
2018-11-07 19:48:39,240 usbdriver.UsbDriverAdapter??????????? INFO? - NCE USB COM4 port opened at 19200 baud [main]
2018-11-07 19:48:41,366 util.FileUtilSupport????????????????? INFO? - File path program: is C:\Program Files\JMRI\ [main]
2018-11-07 19:48:41,367 util.FileUtilSupport????????????????? INFO? - File path preference: is C:\Users\Toshiba laptop\JMRI\My_JMRI_Railroad\ [main]
2018-11-07 19:48:41,371 util.FileUtilSupport????????????????? INFO? - File path profile: is C:\Users\Toshiba laptop\JMRI\My_JMRI_Railroad\ [main]
2018-11-07 19:48:41,377 util.FileUtilSupport????????????????? INFO? - File path settings: is C:\Users\Toshiba laptop\JMRI\ [main]
2018-11-07 19:48:41,384 util.FileUtilSupport????????????????? INFO? - File path home: is C:\Users\Toshiba laptop\ [main]
2018-11-07 19:48:41,386 util.FileUtilSupport????????????????? INFO? - File path scripts: is C:\Users\Toshiba laptop\JMRI\My_JMRI_Railroad\ [main]
2018-11-07 19:48:41,778 server.WebServer????????????????????? INFO? - Starting Web Server on port 12080 [WebServer]
2018-11-07 19:48:43,401 PanelPro.PanelPro???????????????????? INFO? - Main initialization done [main]
2018-11-07 19:48:43,486 server.WebServer????????????????????? INFO? - Starting ZeroConfService _http._tcp.local for Web Server with properties {path=/, json=4.1} [WebServer]
2018-11-07 19:48:48,846 withrottle.FacelessServer???????????? INFO? - Published ZeroConf service for 'richard's railroad._withrottle._tcp.local.' on 192.168.1.15:12090 [WiThrottleServer]
2018-11-07 19:48:48,848 withrottle.FacelessServer???????????? INFO? - Creating new WiThrottle DeviceServer(socket) on port 12090, waiting for incoming connection... [WiThrottleServer]
2018-11-07 19:48:49,364 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 0 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 19:48:49,464 nce.NceConnectionStatus?????????????? WARN? - Incorrect or no response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 19:48:49,469 jmrix.AbstractMRTrafficController???? WARN? - timeout flushes receive buffer: 00 F8 [nce.NceTrafficController Receive thread]
2018-11-07 19:48:59,465 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 1 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 19:48:59,568 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 19:48:59,572 jmrix.AbstractMRTrafficController???? WARN? - timeout flushes receive buffer: 00 F8 [nce.NceTrafficController Receive thread]

Hi everyone, I am sorry to trouble you all again but I am really down. No idea what I am doing and seriously regretting going down this path of DCC controlling Ppoints and installing blocks but all the money is invested and it is slowly progressing. I am trying to follow all of your advice and I seriously appreciate how much time you are putting in to helping out a silly bugger you don't even know.

The upgade chip is installed and I changed the baud rate to 19200. Powercab control is working but no WiThrottle.
I see 7.3.0 in the console log.
I don't know where to find the connection preference to change it to 7.3.*?? I assume it must be on the very first Edit/Preferences page.

NCE? information shows the new AIU I connected in series last night and gave the address of 5 to. I understand these addresses should be changed , but first I want to get the wiThrottle working again.

CAB 3 Usb interface
Cab 4? AIU
Cab 5 AIU



-----------------------------------------

2018-11-07 18:03:15,156 util.Log4JUtil??????????????????????? INFO? - * JMRI log ** [main]
2018-11-07 18:03:15,299 util.Log4JUtil??????????????????????? INFO? - This log is appended to file: C:\Users\Toshiba laptop\JMRI\log\messages.log [main]
2018-11-07 18:03:15,300 util.Log4JUtil??????????????????????? INFO? - This log is stored in file: C:\Users\Toshiba laptop\JMRI\log\session.log [main]
2018-11-07 18:03:15,311 apps.Apps???????????????????????????? INFO? - PanelPro version 4.12+Rb6a9bb1 starts under Java 1.8.0_151 on Windows Vista x86 v6.0 at Wed Nov 07 18:03:15 AEDT 2018 [main]
2018-11-07 18:03:16,239 apps.Apps???????????????????????????? INFO? - Starting with profile My_JMRI_Railroad.3f558d63 [main]
2018-11-07 18:03:16,700 node.NodeIdentity???????????????????? INFO? - Using jmri-dNQe-cAGbhNiaaacjEYECc-3f558d63 as the JMRI Node identity [AWT-EventQueue-0]
2018-11-07 18:03:17,233 xml.AbstractSerialConnectionConfigXml INFO? - Starting to connect for "NCE" [main]
2018-11-07 18:03:19,807 usbdriver.UsbDriverAdapter??????????? INFO? - NCE USB COM4 port opened at 9600 baud [main]
2018-11-07 18:03:30,102 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 0 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:03:30,205 nce.NceConnectionStatus?????????????? WARN? - Incorrect or no response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:03:32,588 apps.PerformFileModel???????????????? INFO? - Loading file C:\Users\Toshiba laptop\Desktop\Panel25Oct.xml [main]
2018-11-07 18:03:34,516 configurexml.ErrorHandler???????????? ERROR - File not found while opening file /C:/Users/Toshiba%20laptop/Desktop/Panel25Oct.xml Exception: java.io.FileNotFoundException: C:\Users\Toshiba laptop\Desktop\Panel25Oct.xml (The system cannot find the file specified)
See http://jmri.org/help/en/package/jmri/configurexml/ErrorHandler.shtml for possibly more information. [AWT-EventQueue-0]
java.io.FileNotFoundException: C:\Users\Toshiba laptop\Desktop\Panel25Oct.xml (The system cannot find the file specified)
??? at java.io.FileInputStream.open0(Native Method)
??? at java.io.FileInputStream.open(Unknown Source)
??? at java.io.FileInputStream.<init>(Unknown Source)
??? at java.io.FileInputStream.<init>(Unknown Source)
??? at sun.net.www.protocol.file.FileURLConnection.connect(Unknown Source)
??? at sun.net.www.protocol.file.FileURLConnection.getInputStream(Unknown Source)
??? at jmri.jmrit.XmlFile.rootFromURL(XmlFile.java:182)
??? at jmri.configurexml.ConfigXmlManager.loadOnSwingThread(ConfigXmlManager.java:646)
??? at jmri.configurexml.ConfigXmlManager.lambda$1(ConfigXmlManager.java:604)
??? at jmri.util.ThreadingUtil.lambda$0(ThreadingUtil.java:159)
??? at java.awt.event.InvocationEvent.dispatch(Unknown Source)
??? at java.awt.EventQueue.dispatchEventImpl(Unknown Source)
??? at java.awt.EventQueue.access$500(Unknown Source)
??? at java.awt.EventQueue$3.run(Unknown Source)
??? at java.awt.EventQueue$3.run(Unknown Source)
??? at java.security.AccessController.doPrivileged(Native Method)
??? at java.security.ProtectionDomain$JavaSecurityAccessImpl.doIntersectionPrivilege(Unknown Source)
??? at java.awt.EventQueue.dispatchEvent(Unknown Source)
??? at java.awt.EventDispatchThread.pumpOneEventForFilters(Unknown Source)
??? at java.awt.EventDispatchThread.pumpEventsForFilter(Unknown Source)
??? at java.awt.EventDispatchThread.pumpEventsForHierarchy(Unknown Source)
??? at java.awt.EventDispatchThread.pumpEvents(Unknown Source)
??? at java.awt.EventDispatchThread.pumpEvents(Unknown Source)
??? at java.awt.EventDispatchThread.run(Unknown Source)
2018-11-07 18:03:37,393 server.WebServer????????????????????? INFO? - Starting Web Server on port 12080 [WebServer]
2018-11-07 18:03:38,645 util.FileUtilSupport????????????????? INFO? - File path program: is C:\Program Files\JMRI\ [main]
2018-11-07 18:03:38,647 util.FileUtilSupport????????????????? INFO? - File path preference: is C:\Users\Toshiba laptop\JMRI\My_JMRI_Railroad\ [main]
2018-11-07 18:03:38,647 util.FileUtilSupport????????????????? INFO? - File path profile: is C:\Users\Toshiba laptop\JMRI\My_JMRI_Railroad\ [main]
2018-11-07 18:03:38,648 util.FileUtilSupport????????????????? INFO? - File path settings: is C:\Users\Toshiba laptop\JMRI\ [main]
2018-11-07 18:03:38,656 util.FileUtilSupport????????????????? INFO? - File path home: is C:\Users\Toshiba laptop\ [main]
2018-11-07 18:03:38,656 util.FileUtilSupport????????????????? INFO? - File path scripts: is C:\Users\Toshiba laptop\JMRI\My_JMRI_Railroad\ [main]
2018-11-07 18:03:40,208 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 1 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:03:40,308 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:03:41,311 withrottle.FacelessServer???????????? INFO? - Published ZeroConf service for 'richard's railroad._withrottle._tcp.local.' on 192.168.1.15:12090 [WiThrottleServer]
2018-11-07 18:03:41,312 withrottle.FacelessServer???????????? INFO? - Creating new WiThrottle DeviceServer(socket) on port 12090, waiting for incoming connection... [WiThrottleServer]
2018-11-07 18:03:43,314 PanelPro.PanelPro???????????????????? INFO? - Main initialization done [main]
2018-11-07 18:03:50,309 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 2 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:03:50,410 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:00,412 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 3 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:00,512 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:10,513 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 4 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:10,613 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:20,614 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 5 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:20,714 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:30,715 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 6 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:30,815 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:31,880 server.WebServer????????????????????? INFO? - Starting ZeroConfService _http._tcp.local for Web Server with properties {path=/, json=4.1} [WebServer]
2018-11-07 18:04:40,816 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 7 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:40,918 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:50,920 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 8 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:04:51,020 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:05:01,021 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 9 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:05:01,122 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:05:11,123 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 10 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:05:11,224 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:05:21,225 jmrix.AbstractMRTrafficController???? WARN? - Timeout on reply to message: AA consecutive timeouts = 11 in nce.NceTrafficController [nce.NceTrafficController Transmit thread]
2018-11-07 18:05:21,325 nce.NceConnectionStatus?????????????? WARN? - No response from NCE command station [nce.NceTrafficController Transmit thread]
2018-11-07 18:05:21,332 jmrix.AbstractMRTrafficController???? WARN? - timeout flushes receive buffer:? [nce.NceTrafficController Receive thread]
2018-11-07 18:05:21,336 nce.NceConnectionStatus?????????????? INFO? - NCE EPROM revision = 7.3.0 [AWT-EventQueue-0]
2018-11-07 18:09:03,634 jmrix.AbstractMonPane???????????????? WARN? - File selection dialog box did not provide a path to the specified file.? Log will be saved to C:\Users\Toshiba laptop\JMRI\My_JMRI_Railroad\monitorLog.txt [AWT-EventQueue-0]
2018-11-07 18:09:05,435 jmrix.AbstractMonPane???????????????? WARN? - startLogButtonActionPerformed: getSelectedFile() returns monitorLog.txt monitorLog.txt [AWT-EventQueue-0]
2018-11-07 18:09:05,436 jmrix.AbstractMonPane???????????????? WARN? - startLogButtonActionPerformed: is attempting to use returned file path and file name C:\Users\Toshiba laptop\JMRI\My_JMRI_Railroad\monitorLog.txt [AWT-EventQueue-0]

---------------------------------------------------------

Am 06.11.2018 um 22:03 schrieb tnmkumar_us:

Also, I understand that SoundPro can be used to play sounds even if the locomotive does not support sound.
Is it possible to test this also in offline mode?

Yes, it is.

See for details.

Here are two short video examples playing sounds in simulator mode:




Klaus