开云体育

I'm just trying to start digital comm and need help. What hardware is needed between my IC7000 and a Lenovo PC? Thanks

I have a S9 noise level on 20m all the time. The other bands are around S3. Anyone else have similar noise? Ed

So, I have recently moved my IC-7000 to my truck, connected to an ICom AH-4 tuner mounted in the bed for HF. The 2m/70cm antenna is also in the truck bed. When transmitting VHF, I am getting reports which seems to be ignition noise interference. At this point, I have some the remote head cable wrapped though some ferrite. Not sure what else would be recommended...just ferrite everything up as much as possible? Any other ideas? Grant VA6GT

I have contant cw on all bands when in the CW Mode. Any clues?

It is appreciated that if anyone can give some repair hint. my 7000 off freq e.g 11xmhz when 146mhz selected during the low power transmission (1w). It is same problem in 70cm band too. Anything above 5w is working perfectly. Wondered if anyone had same issue and has fixed.

https://forums.qrz.com/index.php?threads/icom-ic-7000-transceiver.908988/ Not mine, just sharing.

Just found the rotary switch on the bottom left of the faceplate (PBT/M-ch RIT) won't push in so I have limited capability to get to the memory channels. Looking to get a replacement. Will KA3UQQ

I am trying to set up VARA FM with my 7000. Is it true for VHF I have to use the 6 pin data port on back and not the 13 pin port?

Would like your IC-706 mk ll G in an exchange or part-exchange deal with my immaculate IC-7200, side handles, fitted leather case, all original accessories, large binder of manuals reviews, mods. A deal may only be possible in the UK due to high carriage costs, but try me anyway!

Hello Group, I think this is my first post here. My name is Dennis and my station call is AI6R. First off I love my Icom 7000 and I use it weekly, but just recently it started miss behaving when using the FM or AM modes. It works OK using SSB. I, at first thought, it might be the MIC or MIC cable, but since it works well in the SSB mode it would seem that the MIC and MIC cable are OK. I've been through the manual several times looking for some setting that I might have set or changed. Nothing stood out as a proplem with any particular setting, but ... Any advice on my particular problem would be much appreciated. I miss my evening nets on 2m's. Thanks for any suggestions, Dennis ... AI6R

I live in Montana. Where is a good place to send my IC 7000 in for repair ? Thanks for any recommendations. James

I own a IC 7000. The + 13.8 volt line touched the IC7000 ground. How much damage can this do ? I assume this has happened to others . The radio draws a lot of current and will not turn on ! Thanks for any info. (guesses) James

Where can I buy/source the plastic plug with pins to go into 12v receptical on back of the IC-7000? Is there a particular reference number for that plug? I want to make my own customized power cord? Any help appreiated? 73 de W3MIK Mike Yahoo Mail: Search, Organize, Conquer

Anyone had this issue. Powered by a LiPo battery and using a 1/4 vertical with a wolf river coil with an swr less than 1.5. When transmitting CW at 100 W, the unit will shut down. If I turn down the power to 25 W this won't happen. Doesnt happen on 20m. Any ideas?

Hello folks. Looking to the braintrust for some input. My 7000 shuts down when I key the mic. Its installed in my pickup under backseat. 10M is roof center 2/3s to the rear of truck roof. 2M antenna is on lip mount on right side of hood close to front. I know its not a low voltage issue. I have it hooked directly to a fully charged LiFePO4 100ah battery (13.4v fully charged). Voltage drop when keyed is less than a tenth of a volt. The radio is grounded with a 12" 12awg wire directly to mounting bolt of seat belt (so excellent ground). I thought an RFI issue, but even when RF Power is turned totally down(</=5w, it still shuts off. What am I missing??? Any help would be great appreciated. Mike

I want to operate WSJTx with my 7000. I've connected the radio to my laptop, via a rigblaster advantage and am using Ham Radio Deluxe for rig. control. FT8 is decoding fine. Just wondered if there are any settings on the actual radio that I need to configure, to ensure a good receive and transmit signal. Info on this is sparse on the Internet Apologies if this topic has already been covered.

SOLD! Thank you! Mike WA3O