开云体育

Going to try that later. ?I did try a range of long addresses but I get the feeling the the DR5000 will not let it change like a stuck memory if that makes any sense.

Might seem daft but have you tried programming a higher address in, think my highest is 9007, I can’t remember seeing anything in the manual about certain addresses being blocked so it may well be

Hi Andy, Thats the strange thing the DR5000 app on my PC is what I have been using, now that shows the new address when you read it. ?But it will not let you run the loco once out of program mode.

Hi Douglas, What does it say when you read the address, I’ve found the sometimes if I use the Z21 app to program long addresses it doesn’t work, the address stays the same. I now only program

I have had my DR5000 since about September and have it paired with a 5033 booster.? I have now had a some strange behaviour with the addresses on ESU Loksound V4 decoders. Today I bought a new loco

I have been using Rocrail with Digikeijs products though I havn't fully explored the full range of possibilities yet. There is extensive input, both in German and English about using Digikeijs

What is it that you want to know about ITrain? James or me can provide the answers as the forum is not open. Iain Morrison 07767 456746 ________________________________ Sent: Wednesday, March 11,

Hi Dennis, have you asked XanderB? at www.berros.eu ( http://www.berros.eu ) , much of the forum had digikiejs info, english site is https://www.berros.eu/itrain/forum/viewforum.php?f=1 how do i get

Hi all. I have a DCC bus that has a voltage of 14.5 volts measured using an RRampmeter. The input to my DR4088CS is the same at 14.5 volts, the no load output is 0.9v lower on all 16 outputs at

Get some cable-ties and cable-tie mounts and just tidy them up Cheers G George Bryan Blaxland NSW Australia

thanks once again, i didnt twist them, just checking. next question, Do they have to run as in 'parallel as in tidy' using spacers separated from each other, in one section theres 8 brown+ pos wires

Do not twist them, you will be in all sorts of problems with false signals if you do. Just keep them nice and neat then you will be ok ? Iain Morrison 07767 456746 Sent: 04 March 2020

do i twist the track feed back to to dr4088 the negatives wire all connect in each block and over many blocks, but twisting the positive wire around the negatives is impossible, then if not, how far

I have searched this forum and many other sites and videos to find if the live wires from track to DR4088LN cs are twisted or not. I dont see how they could be! In Ireland electrical wiring is

Jay, Impressive write up! I'm not sure how many is too many either.? I currently have 8 connected on mine. What happens is when you click on the booster tab it interrogates the boosters for a

Looking for a few members, if you are interested, in making Documents for the following: Links will be helpful also. ITrain RocRail Train Controller Like to get Setup information using the Digikeijs

Hi James and Ryan, you are correct - clicking on the "Boosters" tab of the DR5000 Loconet Properties window with more than a few boosters will cause the DR5000 application to hang.? I have no way to

George, I have done what you are proposing.??I have a yard where a dedicated Arduino watches for Loconet Block Occupancy and Transponding/Railcom messages issued by the DR5088RC. I don't direct

This is exactly what I do using iTrain to control the layout and display what is where. I also use DR5088RC for this purpose. Will be harder if you are using a home brewed product, but it can be done

Has anyone had any experience reading a Loco ID using a DR5088RC then stopping that train. I have a hidden staging yard with both through and dead-end roads. The roads have sensors which can sense