Welcome to the YaMoRC/Digikeijs English Forum
?
This Table of contents provides information about the YaMoRC and Digikeijs products in US English and JMRI.
Click on the "Read More" to see all the information.
Legal notice:
All instructions are written to the best of our knowledge and belief of the respective authors.
Nevertheless, no liability for any errors or omission in the Documentation is intentional!
?
General:
The Main website of the manufacturers YaMoRC and Digikeijs can be reached via the following link:
- Link to the
- YaMoRC Support for Documents. TBD
- Link to the Digikeijs Firmware:?The latest firmware for each product will be in its respect file directory if we have the latest firmware.
- This is an archive that was made and will have documents in other languages. Check before you download.
?
US Dealers:
- for YaMoRC and Digikeijs Products.
Click on any RED Model number below, it will send you to the files page for that device.
English Only Manuals and Photos, etc can be found on this Forum and elsewhere:
Central Station:
- DR5000 The first Command Station with all conceivable connection sockets and LED status lights, USB, LAN & WLAN
- Detailed Tutorial - Rudy's Model Railway Videos on DR5000
Booster:
- DR5033 3 amp Booster works with many different Command Stations
Switch and Servo Modules:
- DK50018 16 Channel Bluetooth accessory and switching decoder
- DR4018 16 Channel Multi-Protocol Switching Decoder
- Manual: DR4018 Advanced V1.2
- Video Series for the DR4018 or DK50018 on Preset 1 in JMRI to invert the outputs for LED Signals.
-
- Guide for Testing the DR4018/DK50018 for proper Preset Configuration.?
- DR4024 4-output multi-protocol servo decoder with 4 additional switching outputs
?
Feedback Modules:
- ?DR4088CS & CS-GND 16-input feedback module (S88)
?
- ?DR4088LN-CS, LN-GND & LN-OPTO 16-input feedback module (LocoNet)
-
?
- ?DR4088RB-CS & RB-OPTO 16-input feedback module (R-Bus)
?
- ?DR5088RC 16-input feedback module with RailCom (LocoNet)
?
Reverse Loop Module
- ? DR5013
- Video :?
Turntable Module
- ??? DR5052
?
Other Equipment
- ??? DR4050 DigiLEDs RGB Model Train Light Control
?
- ??? DR5022 DigiControl for the control of 2 trains via a swivel
?
- ??? DR5039 LocoNet-B to CDE
?
- ??? DR5097 DigiNetHub 10x LocoNet Hub
?
- ??? DR5098 DigiNetHub 10x X-Bus Hub
?
- ??? DR5099 DigiNetHub 5x X-Bus Hub & 5x LocoNet Hub
Software
- JMRI
?
- RocRail
-
- ITrain
- Train Controller
- Perecli RRA (Railroad Automation)
- ?
- ?
- ?
- ?
- ?
-
- AnyRail:
Throttles:
- Document showing the Apps that work with JMRI and DR5000 with download links.
- Roco WLANmaus Throttle Setup For The Digikeijs DR5000
- Test of the Proto-Throttle with the Digikeijs DR5000
- RtDrive Lenz With The Digikeijs DR5000
- ESU Mobile Control II Throttle With The Digikeijs DR5000
- DigiTrainsPro (Android Phone) DR5000 Setup (Now a monthly fee of 5 Eros for this version)
- Z21 App for Apple or Android Phones.?
?
Other Features:
- ?
?
?
?
|
Welcome to the Digikeijs Forum.
Welcome, hope you find this forum educational and full of great ideas and feedback.
This forum will be a little different.? I have always had issues with forums that want the same problems asked
By
Dennis Cherry
·
#1
·
Edited
|
|
Additions to the Wiki Table of Contents.
When additions are added to the Wiki, I will be sending out a notification to all members what is added or changed.
Added;
* Perecli (Railroad Automation) in Software link:
* ABC Braking to Other
By
Dennis Cherry
·
#2
·
Edited
|
|
Weekly New Links
New this Week:
*DR4018 using Bachmann Switch Turnout ( https://www.youtube.com/watch?v=J_p20B6i6EE )
* *Setting up Railcom in JMRI. ( https://www.youtube.com/watch?v=gx987a9aALI )
* *Using Railcom
By
Dennis Cherry
·
#3
·
|
|
Which Digikeijs products do I need ?
I wonder if you could please help me ?
I have commenced construction of an HO North American railroad layout in my home.
I am using Lenz DCC XpressNet for locomotive control, DCCconcepts for servo
By
Alastair <Raider844@...>
·
#4
·
|
|
Re: Which Digikeijs products do I need ?
Alastair,
Yes, the D R4088LN-CS will work for your block control.
The DR5013 DigiReverse will take care of the Y.? It also has block detection built in.?
If you aren't using the DR5000 then you will
By
Iron Planet Hobbies
·
#5
·
|
|
Re: Which Digikeijs products do I need ?
Hi Ryan,
Thank you for your outrageously swift and helpful answer !
I am Scotland ???????
Cheers,
Alastair
+44 743 628 9136
Raider844@...<mailto:Raider844@...>
Sent
By
Alastair <Raider844@...>
·
#6
·
|
|
Re: Which Digikeijs products do I need ?
A
I concur with Ryan - I feedback each point with 4088 - but that is personal preference
JC
Sent from my iPad Pro
By
John Critchley
·
#7
·
|
|
JMRI and DR4024 turnout status
Hi. I'm looking at using Dijikeijs products with JMRI to control turnouts and signals on a new O-gauge layout. If I use a DR5000 with DR4024s to drive turnout servos (with DR4102s to handle frog
By
Ian P
·
#8
·
|
|
Re: JMRI and DR4024 turnout status
Ian,
Yes, the turnout status is controlled with a LT command.? This will reflect on your JMRI panel just like a Digitrax DS64 or any other LocoNet controlled device.??
Ryan
By
Iron Planet Hobbies
·
#9
·
|
|
Re: JMRI and DR4024 turnout status
DR4024 is a service controller only, no feedbacks included. You will need to use microswitches and a DR4088GS or opto to send the feedback
By
Iain Morrison
·
#10
·
|
|
Re: JMRI and DR4024 turnout status
Ryan, I don’t think that the 4024 is actually providing feedback, it only reacts to the command sent and JMRI is inlyvchnaging only chaging the status based on the command sent to change the servo,
By
Iain Morrison
·
#11
·
|
|
Re: JMRI and DR4024 turnout status
Thanks for the replies. What I was trying to establish was what 'Feedback mode' would I be able to use when I configure a turnout in JMRI. Will a DR4024-controlled turnout allow me to use ONESENSOR or
By
Ian P
·
#12
·
|
|
Re: JMRI and DR4024 turnout status
I don’t actually know JMRI but going by other software you will be using direct mode as you not have any sensors unless you do the micro switch thing I describe earlier
Iain Morrison
07767
By
Iain Morrison
·
#13
·
|
|
Re: [Digikeijs], JMRI, Rocrail, Itrain, Walthers, Tortise, Cobalt,Switch Machine, Roco, Throttle JMRI and DR4024 turnout status
Ian, yes you are correct. If you need physical feedback from the turnout (to prove it actually moved), you would need a micro switch or something attached to the turnout that can trigger a sensor.
By
Iron Planet Hobbies
·
#14
·
|
|
Re: [Digikeijs], JMRI, Rocrail, Itrain, Walthers, Tortise, Cobalt,Switch Machine, Roco, Throttle JMRI and DR4024 turnout status
Thanks for clarifying things. I thought I'd read somewhere that some servo controllers (I think it was ESU's) do provide feedback without additional microswitches and I was wondering whether the
By
Ian P
·
#15
·
|
|
Z21 android issue
Hi I have just obtained a dr5000 unit and set it up a cording to instructions.
However, when trying to connect any of my android drvices (phone and tablet) I cannot connect to the x22 app.
My devices
By
David Philip <dvdphilip1@...>
·
#16
·
|
|
Re: Z21 android issue
OK let me get up to speed on your issue.
1. When you connect your phone to the WiFI what is your connection name?
Resolved; need a firmware update.
Dennis
By
Dennis Cherry
·
#17
·
Edited
|
|
Boosters
Hello
I’m new to digikeijs! I have questions I can’t figure out! For now one. Why when I try to program a DR 5033 to I get a timed out?
George
By
George Wiesner
·
#19
·
|
|
Re: Boosters
Greeting and welcome to our website.
* Tell us what procedure you are using to program the DR5033?
* What do you want to change?
* How do you have it connected?
Dennis
Owner and Moderator
By
Dennis Cherry
·
#20
·
Edited
|
|
Re: Boosters
Ok
I have already programmed an address no problem! I’m trying to Configure CV3! I get it all finished with a value of 10 and hit the lightning bolt to program and it starts an the I get a red time
By
George Wiesner
·
#21
·
|