开云体育

Ok small update. Got my laptop out which I use to control my backup and second YD7001 and it conects perfectly fisrt time with my first YD7001 by USB and ethernet. So my problem is the Windows 11

Hi all, This is driving me mad I cannot get round it. I have had this system running fine for over a year (upgraded DR5000) and it has been fine. A few days ago I had to restart my router and the

Update on my problem with YD001 upgrade. I returned it to the dealer that I purchased the upgade from and he discoverd that the wifi update had not been saved for some reason. The YD7001 has now

@karst.drenth: Your timely reply is very much appreciated. I will follow your advice and will be ordering YD7432 Reversers as well as an ESU L.Net converter. Also, I am looking into connecting

They don't have to be *detected* , but have at least the *same voltage drop* (1.1V) as the sensor tracks are measuring for. You also can (or better should if you have more Current-Sense detection )

You ask whether the YD7432 will work when “connected via S88 for occupancy monitoring” – the YD7432 uses LocoNet to provide the occupancy reporting, not S88 ? Sent: 08 January 2025

@karst.drenth Could you please elaborate why it matters to have "sections adjacent to S1 and S2 to also be supplied with a current sensor" ? In a reversing loop, sections S1 and S2 are usually next

yes the snubbers the cobalts are powered by dr5000 the cobalt frogs are wired frog to the common and the track feed for the frogs are left and right on the cobalts I am not using the frog connection

By resistor packs do you mean DCC Filters (snubbers)? Are you using the frog output on the Cobalts? If you are then you will be powering the frogs from the accessories bus I.e. the YD9401. When

ok bought some of them resistor packs I have two boosters for the track power only and the point motors all run from the dr5000/9401 put the resistor pack on the dr5000 and when I change? a

Hey Rick, I had a chance to test the 7010 station a bit last few days and I like it. Connection is flawless. Lots of futures and possibilities.

Based on that page, you're not going to get RailCom on S88, you'd need S88.2. There is a lack of RailCom detectors that will work on other systems (ESU and Roco have ones that only work with their own

I would like to try and test some RailCom futures. At the moment the only available detection unit comes from LoDi. Can that unit be connected directly to the YaMoRC 7010 station on the S88

Rick, Why would you need to program using a throttle or Z21 app if you have DecoderPro? The key to understanding JMRI is that if you're using POM, JMRI is storing the changes in the roster file, so

I bought a few of these YD8116 modules mainly for turnouts. For slow motion switch machines it only takes a press of the 'Pgm' button and 1 turnout command to set all addresses for all 8 turnouts as

The YD8116 does have 16 switchable outputs but each turnout uses 2 outputs (straight and branch) therefore only 8 turnouts can be controlled ? Many Thanks Iain

This is probably a really dumb question..... I need some extra outputs for signals and so I need to buy some additional signal decoders. So I was reading the user manual for the YD8116. I was under

I do the same here, make my own resistor wheels. There are several company's that do make resistors wheels in the USA. I did not show all the wiring because that does not change on wiring the

Dennis Pre-made resistive wheelsets are not something I have seen in Europe, I use SMD resistors, superglue and silver conductive paint. You appear to be connecting to the global detector K to

There are many resistor wheels available, the 10K resistor wheels are popular from different MFG.s In my picture of the DR5088RC the green buss bar is the "K" connections to the DR5088RC. You will