开云体育

John, I looked in the /dev directory and do not have a ttyO1. Below are the contents of the /dev directory. root@beaglebone:/etc/ax25# ls /dev/tty* /dev/tty /dev/tty19 /dev/tty3 /dev/tty40

Hi all. My last attempt didn't seem to post so I'll try again. I've been trying to get the sstv from www.instructables to install. I get as far as gcc -lgd -lmagic -o pisstv pisstv.c and it comes

Hi everyone. I've been trying to get pisstv installed on my Pi. When I enter gcc -lgd -lmagic -o pisstv pisstv.c, it comes back /usr/bin/ld: /tmp/cco9lrR5.o: undefined reference to symbol

Many thanks for the information Scott I will give it a try. It seems that I am going to be busy. Thanks to all of you who responded with most helpful advice. 73 Stan GW3SRM

Jay, Are you sure the port is /devtty/S0? -On mine it is /dev/ttyO1. 73, John G8BPQ _____ From:

I was directed to post here for help. I cannot get the AX25 running on either of my BBB using a TNC-Black. I have been to a lot of sites and they just don't help. If some one has done it and can help

[Raspberry_Pi_4-Ham_RADIO] wrote: Stan, there is a program called 'xming X Server for Windows' that will allow you accomplish what John mentioned. You can use it with putty to ssh in and grab a x11

Hi all, I just got my TNC-Black and am setting it up and can not get the ax25 working.When I run kissattach command i get this error "tty_speed: tcgetattr: Input/output error" I have my TNC set

[Raspberry_Pi_4-Ham_RADIO] wrote: Stan, like Alan I use xrdp also. XRDP is much easier to setup then VNC but as Alan said make sure you setup SSH so you can use PuTTY or some other terminal program

Thank you for your reply John. I should have mentioned it, but my granddaughter and myself are using Windows 7 on our laptops. 73 Stan GW3SRM

I am confused! Should I be able to run a Linux system (RoboLinux) remote with audio from a Win7 computer? -- John Ferrell W8CCW Julian NC 27283 It is better to walk alone, than with a crowd

If you are using linux, you can use ssh -X (pi hostname or IP address ) and run the pi's X-Windows session on your linux PC. The X-Windows runs better on a PC than it does on the pi. I mention this

Thank you for your very prompt response Alan. You have given me something to work on. I will have to find the previous posts that you referred to and emulate a setup with my RPi B+ before passing the

Hi Stan, just to kick the discussion off ....is this a firewall problem?? To use the desktop I used xdrp on the Pi and remote desktop connection from windows pc (see previous posts to the group) For

Greetings everyone, I am a new member. I have a problem successfully connecting a VNC (tightvncserver) between a laptop computer and a RPi B. The RPi B and the laptop are my 11 yr

Have you tried Vox mode on the radio? I read somewhere that it might need to be enabled for certain radios. Maybe that will get things transmitting?

Thanks for the tip on get get_ params. I have not got it working yet. I am copying other stations, but it won't transmit. Xastir says it is but the ptt lite doesnt come on.

Hi Jim, I'm sure you're aware of the WSPR Forum, otherwise it seems this is the place. It sounds like you've got what it takes - but I've found the antenna to be all-important with R-Pi-level power

If there is a more appropriate forum for WSPRRY, kindly point me there. I just installed WSPRRY on a model B. I connected it through a commercially-made 20m band pass filter to a large loop

If there is a more appropriate forum for WSPRRY, kindly point me there. I just installed WSPRRY on a model B. I connected it through a commercially-made 20m band pass filter to a large loop