开云体育

So with the DR-735 in TNC mode, the DR-735 is not asserting COS.? Is that correct. What voltages do you measure from DINAH's JP3 to ground with TNC enabled and the DR-735 receiving/not receiving a

I've been using my DINAH interface with an Alinco DR-735 Dual Band Mobile, and it seemed like all was well. The DINAH and included Mini DIN cable plugs right into the back of the radio, and is nearly

The G707 and the V7 have recessed 6 pin mini din. I had to do as suggested and shave the hub of the connector on the cable a bit for a different application for using a V7 . Les Keegan N4LPK

The Kenwood V7 also has a round hole on the front panel so the supplied cabel will not fit,? I used an exacto knife to very carefully shave off the excess molded? "bulge" to round out the overmold

Problem I found with the G707 radio, is that the supplied Cable that came with the Dinah can't fit into that recessed port on front of radio. Have to resort to trying another radio with a rear din

In the Simpleusb-tune-menu RX boost is enabled Echo is disabled Pre and De emphasis both disabled PLfilter is disabled DCSfilter is disabled PTT mode is LOW COSFROM is USB CTCSSFROM is NO RXONDELAY is

Hi Scott, can you give me the settings to allow the Dinah to work with the TM-G707 Regards 73

You just need to bridge JP11-3 to 4.? This provides sufficient current through the SSR input LED for it to operate when the default JP4, JP5, JP6, and JP7 setting are used.? Bridging 1&2 halves the

Getiing about 3,2 Volts on the COS which drops to zero with incoming rx.? ?I have on JP11 1&2 bridged,? and 3 & 4 bridged.? ? Any other jumpers require changes from default ?

Recently installed most current version of Hamvoip.? Running on a RPi3b+ with a Dinah and a Kenwood TM-G707.? Everything works great when I use my 2nd G707 and I can see all DTMF being decoded

Using option2 in simpleusb-tune-menu, do you get anything on the meter when you transmit to the ft-8800 from another radio? -Michael Sent: Tuesday, February 7, 2023 6:08 AM To: [email protected]

Here is the output from "P" menu [image: image.png] Regards, Anthony (N2KI)

Can you show us option P from the simpleusb-tune-menu? It will look similar to this: [cid:image002.png@...] -Michael Sent: Monday, February 6, 2023 6:56 PM To: [email protected] Subject:

With either HamVoIP or ASL, any changes that you make in alsamixer or amixer will be overridden by which ever USB channel driver you are using when Asterisk is loaded. I have a custom script on a

I do not believe that AlsaMixer is used in the HamVOIP distribution.? Anybody know if this is correct?

I check alsamixer and the mic was MM. I changed it but it didn't make a difference. Neither did changing packet speeds in the radio. I checked the jumper again on the board too. Set to Pin5 1200 bps.

I think this is due to the baud rate for packet. Depending on what speed the audio goes out that pin. Pin 1 is audio INTO the radio. Pin 4 is 1200 Pin 5 is 9600 The DINAH has a jumper to choose pin4

When you open asterisk with asterisk –rvvv, the v’s determine the verbosity and it will stick on the highest. 4 V’s would mean level 4 To change it lower, use set verbose 3 or core set verbose 3

I dont think my emails are going through so I will reply here. The DINAH has a jumper that determines whether pin4 or Pin5 are used for audio from the radio. The radio determines this based on the

Steve, It doesnt appear that I am getting any inbound audio from the 8800 to the Dinah board. I think that is Pin 1 on the radio port. Regards, Anthony (N2KI)