开云体育

I also hit the wrong key in the CLI screen. There was a message that said Verbosity was 3 and is now 4. How can I correct that? [image: image.png] Regards, Anthony (N2KI)

Steve, OK the only thing I had to change was Item F to ENABLED. The other issue I don't understand is the radio is acting like it is in cross band repeat. So I have the node on the right side monitor.

I think you may have COSFROM set incorrectly.? Use "V" to verify the following telemetry display when your node is in receive. Here are my settings: Here is my simpleusb_tune_usb.conf file showing

I have a number roadblocks. When I key my HT (THF6) to the 8800 with the PI/Dinah, the 8800 keys and then drops after a second or two. The Pi does not respond to any DTMF input. It does respond using

Yes - I currently have a DINAH connected to an FT-8800.? How can I help?

Anyone using a DINAH board with an FT8800?? I m not understanding some of the setup.? ?Thanks! Anthony N2KI

Update - in case someone else stumbles over this thread. Got it to work via the front RJ45 connector and the Speaker Port in the back - for now. This will be limited to 1200 but it's a start.

Hi Chris, It's the exact same island and I should be there at the same time. I had a tragic event which occurred with my family here in Canada last June, but I will be back In Barbados for Christmas

Hi. Which Caribbean island? I’m visiting Barbados in February. 73, Chris <https://www.qrz.com/db/ve3rwj> VE3RWJ on qrz.com <https://twitter.com/smartguitar1> Follow Me On Twitter Sent: December 3,

Good Morning Mike and fellow members. I am a Canadian/Caribbean Ham and have been an echolink/IRLP user for a quite a few years. I am fascinated how the digital technology have propelled us to higher

Hi MK, did you get this going? Cheers.

Hi Michael, Thanks - no, I don't have a power meter (yet) but I can measure how much power the radio consumes - should give some indication re TX Power. What I could do is to use a signal generator

Regardless of audio level, the HT should see a signal at least when PKS is grounded. Do you have a watt meter to see if the radio is transmitting when PKS is grounded? -Michael Sent: Wednesday,

Greetings, I have a PAUL board connected to a Kenwood TM-271a via the internal pads (not the mic/speaker connection) https://www.arcomcontrollers.com/documents/rc210/tm-271a_mod.pdf - RX works, I can

Our own group knows that song! ?Fear of digital, fear of linking, fear of education, drilling and exercising radio skills and ICS. ?Three guys led the exodus. ?Adios! ?Did my job as EC for me by

Michael- Actually Club politics got in the way. one of our OCD officers? and a schemer accomplice demanded that the DR2X only be worked on (integrated to ALLSTAR)? at the repeater site on the post

Larry, which port did you settle on using? I am about to add AllStar to one of our clubs dr2x's as well. Any struggles that you've come across since putting the system in place? I have allstar in

This may be of interest to y'all living near Mississippi, otherwise please ignore. Thank you. Greetings y'all: The Jackson County Amateur Radio Association (JCARA) is hosting a Hamfest on November 11

One thing I do know is that the manufacturer says to not expect much success over 4800bd On Wed, Aug 3, 2022 at 15:17, Patrick Perdue<borrisinabox@...> wrote: Hi: Someone on a local repeater was

Hi: Someone on a local repeater was asking if the Alinco DR735 with it's DIN connector has the same audio quality as the older DR135. Anyone have experience with this radio used in combination with a