开云体育

Paul; This leads to a few questions - when is EEPROM written? Are there triggers, if so, what? I have a specific sequence for powering off my station - Power off the K3s (both with KIO3As), then

I have difficulties with configuration of my SO2R station with 2 Yaesu 101MP radios and I am wondering if N1MM allows 2 radios with 2 receivers. Every time I try to sync the two receivers on one of

Hi Mike, I suspect that under some circumstances if the voltage drops slowly the microprocessor gets into a state where it is running but there is not enough voltage to properly write EEPROM. If it

Paul, on Nov 11 I ran into this situation: I was setting up vm (dvr voice messages) on two K4Ds on Saturday. ?Using TRLinux and a YCCC SO2R Box + (this right probably only applies to two or three

Hi Paul, All seems to be good. I looks like the PSU went to protection / Vout goes to zero and would not recover unless the load was removed. Very strange but this one was not a cheap switching PSU,

Intermittent failures are the most difficult to find. I'm glad you got it. Paul wrote:

Aand.. As is traditional, the problem is never the actual device. My apologies for taking the BW. The "wall wart" PSU had a strange, intermittent failure, all was good for over 10 years but now it

If you conclude that the SO2R Box has a hardware problem let me know what you find and I'll try to help debug it. Paul wrote:

I got back to this. I re-did my N1MM setup with all the necessary SW pieces in between the YCCC box and and N1MM. It takes some tens of minutes and then the connection is again lost.? Power OFF/ON

I'm not sure I understand. What is activating PTT when you send the phone message? It may be possible to add something to the SO2R Box program but I need to understand it better. If it is mode

SO2R state 0x07 means that TX2 is selected, RX2 is selected, and Stereo is selected. That is what you are setting so it is correct. The only things I can think of are that the SO2R Box firmware is

Hi Now I can see what the OTHER HW glitch is. When I press Stereo, PTT is set and this is seen in my other interface card based control HW. IT is NOT a HID device conflict as the control HW is

I don't think the utility has a way to save the log. It is pretty old. The best thing to do is to take a snapshot of the window. Paul markku.a.oksanen@...> wrote:

Really looks like I must have an other HID device on my system that "likes not" the SO2R box connection. How could I figure out ?what it is?? Markku ________________________________ Sent:

Hi Just turned things OFF. Did verbose However the SW is not supporting copy/paste for this email. Is there a log to send? Click RX R2, TX R2. Click Stereo HOWever, I see that one OTHER SW on my

I just tried the same steps and it worked with my SO2R Box. I am running the same utility and firmware versions. Could you click verbose Output on the SO2R Box Utility and then try those steps agan?

Hi Paul, Well this is what IT support should look like ?: I am using firmware 1.6.0 and the utility says version 1.8.0. I just did the reset, it says Device removed Device attached And when I

Hi Paul, Well this is what IT support should look like ?: I am using firmware 1.6.0 and the utility says version 1.8.0. I just did the reset, it says Device removed Device attached And when I

Paul, Here is a situation that I just ran into and I am sure I am the only one with it.? Setup: TRLinux 0.49, SO2R Box +, K4D, using voice memories in K4D, foot switch connected to SO2R Box

I just tried this with an SO2R Box. Clicking Stereo causes it to receive from both radios. So I cannot reproduce this problem. What version of the SO2R Box firmware are you using? You might try