¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Winfldigi
  2. Messages
Expanded Topics Messages Polls
Date
Hide TX Section of the FLDigi Screen

 

It would be nice if there was an option to hide the TX portion of the screen to allow more room for RX traffic.
?
I am not doing any transmitting and I am sure other hams and SWL folks just might desire more receive room on the screen.? I already have set Rig/Log Controls to None.
?
Whoever the powers to be are, please consider this.
?
Thanks very much.? This is a great program.
?
Regards,
George, NJ3H
Redmond, Oregon USA
flrig server/client question

 

I found "Hamrs" software to assist in logging Pota stations, and although there are a few settings I don't like, this email is to ask about the server/client option flrig provides ( used by Hamrs).
?
when I use flrig, on my desktop, but qsy via wsjtx, flrig follows by cat port used.
?
If I use hamrs on a laptop, then use the server/client option on that laptop.? ?hamrs on that maching, will cause the main machine to follow and cause the radio to qsy ( although mode dos not follow)
my question, is , Is the main flrig suppose to go backwards and cause the client to qsy.? it does not at this moment
?
?
?
it seems to be one way only.? is that correct?
?
?
?
?
Re: Fldigi UI has me flummoxed

 

Thanks again Robert.

I was trying to help a friend. The blind leading the blind, with the ignorant for consultation.??

Bill

On Thu, Mar 27, 2025 at 4:14?PM Robert, KK5VD via <kk5vd=[email protected]> wrote:
Bill,
? ?Looked over the source code related to your question. The widgets in question is a custom UI element and the code contains no assignment (text message) to the tooltip() function. The reason for no tool tip.
Robert
Re: Fldigi UI has me flummoxed

 

Bill,
Looked over the source code related to your question. The widgets in question is a custom UI element and the code contains no assignment (text message) to the tooltip() function. The reason for no tool tip.
Robert
Re: Fldigi UI has me flummoxed

 

Don and Robert, You're the best. Thanks.?

Robert, you answered?the question I didn't even ask, but was thinking about!

Bill


On Thu, Mar 27, 2025 at 2:58?PM Robert, KK5VD via <kk5vd=[email protected]> wrote:
Under Fldigi Configuration->Configure->UI->General is a checkbox in the upper left hand side of the dialog box named "Show tool tips". Make sure this is selected. Hover the cursor over the UI in question for a few seconds. A text message should pop up with some additional information about the UI. Sadly in this particular case it seems it doesn't show a tool tip for the widgets is question. I realize this doesn't help you in this case, but info for other UI widgets.

Robert
Re: Fldigi UI has me flummoxed

 

Under Fldigi Configuration->Configure->UI->General is a checkbox in the upper left hand side of the dialog box named "Show tool tips". Make sure this is selected. Hover the cursor over the UI in question for a few seconds. A text message should pop up with some additional information about the UI. Sadly in this particular case it seems it doesn't show a tool tip for the widgets is question. I realize this doesn't help you in this case, but info for other UI widgets.

Robert
Re: Fldigi UI has me flummoxed

 

This depends on the rig and the rig control?software being used.

In general, the left hand field displays the mode of the rig IF this is handled by rg ctonrl software.

In general the right hand field would be filter width?IF filter width is controlled by the rig control software.

On Thu, Mar 27, 2025 at 3:16?PM Bill KD9TWA via <kd9twa=[email protected]> wrote:
I have a super basic question. What is the section of the UI called that contains the frequency window, the logging area, etc., and specifically, the mode and bandwidth section called? It's the area between the header and the macro section.?
?
?
?
I'm looking for a description of all?of the functions in that area. Without knowing the correct nomenclature, I can't search. Is there an image that has ball-notes for each item/button?
?
Thanks



--

73,
AB1PH
Don Rolph
Fldigi UI has me flummoxed

 

I have a super basic question. What is the section of the UI called that contains the frequency window, the logging area, etc., and specifically, the mode and bandwidth section called? It's the area between the header and the macro section.?
?
?
?
I'm looking for a description of all?of the functions in that area. Without knowing the correct nomenclature, I can't search. Is there an image that has ball-notes for each item/button?
?
Thanks
Re: Yaesu FT-818, SCU-17 and flrig 2.0.05 on Win 10

 

I think the issue is the sound card does not have a wide enough bandwidth.
j

On Thu, Mar 27, 2025 at 12:50?AM Oliver von Sehlen via <ollijopp=[email protected]> wrote:
Hi all,
?
Just a little quirk I noticed (and which caused me quite some cursing and despair):
When the FT-818 is in WFM mode (say, used as an ordinary FM radio receiver for your favourite FM broadcast station) and you try to connect it to flrig, the program crashes when trying to initialize the radio.
?
Workaround:
Simply switch the transceiver out of the WFM band (say, to any of the normal Ham radio bands, Shortwave or 2m/70cm) before trying to connect to flrig.
?
Thought you might want to know before running into the same issue.
?
73,
Oliver (DL1OVS)
Yaesu FT-818, SCU-17 and flrig 2.0.05 on Win 10

 

Hi all,
?
Just a little quirk I noticed (and which caused me quite some cursing and despair):
When the FT-818 is in WFM mode (say, used as an ordinary FM radio receiver for your favourite FM broadcast station) and you try to connect it to flrig, the program crashes when trying to initialize the radio.
?
Workaround:
Simply switch the transceiver out of the WFM band (say, to any of the normal Ham radio bands, Shortwave or 2m/70cm) before trying to connect to flrig.
?
Thought you might want to know before running into the same issue.
?
73,
Oliver (DL1OVS)
Re: FLrig control for Icom IC-738

 

Tnx Dave! Hope all is well with you guys and Hello to Skip! 73 de Steve
Re: WATERFALL HEIGHT? #fldigi-parameters

 

¿ªÔÆÌåÓý

Thanks John. That's what I needed. Appreciate it a lot.

Dit Dit

On 3/25/2025 6:29 PM, John KC3FL via groups.io wrote:
Dave,
?
Ck the attachment.
?
John
KC3FL
-- 
73's de NU4N

--
73'S DAVE NU4N
Re: WATERFALL HEIGHT? #fldigi-parameters

 

Dave,
?
Ck the attachment.
?
John
KC3FL

2025-03-25_192634.png

Re: MacBook OS and Failure to Transmit

 

On 2025-03-25 14:23:, W4MRP via groups.io wrote:
Yeah. Some people have a hard time understanding unless they can see it.
Not me...not necessarily...the vid DOES explain very well what you wanted to say.
But for all the words and all the BOLD text, the conversation missed the target for me.

I can sorta see why digirig doesn't want to mention the words "RA Board"
Except they DO mention it, and that is what led to my initial confusion.

It's all written out in the Digirig Lite Setup Manual: <>
It doesna mention fldigi's setting "Rig Control > C-Media PTT"
and why you'd choose C-Media PTT when what you really want is to toggle GPIO3 on the chip. And explain why GPIO3 isn't special...GPIO pins are uncommitted digital signal pins. A lot of detail is not needed, but SOMETHING to help lay a base for learning. (I haven't looked into why pin 3 and not another. I assume some design decision by some folks somewhere....)

They DO mention "RA Board" and "CMedia GPIO3" in the PTT section, though.
Yes, they do...leading to my confusion about needing a board.


has one of the answers, but I needed to read 2 blocks to get the answer.
GPIO3 (RA-Board),
Each can be disabled via solder pads. &&&
PTT by VOX (enabled by default), PTT by GPIO3 (enabled by default)

I now understand this means that
1. Both PTT methods are enabled on the lite as shipped
2. Either method can be used without disabling the other ***
*** This is not stated. Nor is any reason given why one might want to disable one of them, if they can coexist without interfering with one another.

~R~
Perseus and WEFAX Decorers

 

Greetings,
?
I have an issue with the Perseus with FLDigi an BlackCat WEFAX (the only two decoders that I have.
?
Note the vertical interference marks showing on both decoders.? However on the Perseus, there is not such interference shown in the spectrum nor the waterfall view. Both picture attached to show the Perseus is not showing the interference
?
When I use my RSPdx and HF+ Discovery, this situation does NOT occur.? I am using the same antenna for all three radios.? I have tried the Perseus/decoders set with a VAC and also the signal to the PC speakers.
?
Does anyone have any possible ideas what might be causing the vertical interference lines?
?
By the way, I have tried powering the Perseus with a PSU from Jameco and with a USB cable.
?
One more thing:? I can not get the brightness and the other slide switches to work on the right-hand side next to the spectrum/waterfall screen.? I have never notices an issue before.
?
Regards,
George
?

Perseus Spectrum.jpg
Perseus Waterfall.jpg

WATERFALL HEIGHT? #fldigi-parameters

 

Dumb question but on one of my computers I can't seem to expand upward the waterfall.
What setting in FLDIGI config file do move the waterfall up and down.
Thanks Dave
--
73's de NU4N
Re: MacBook OS and Failure to Transmit

 

Yeah.? Some people have a hard time understanding unless they can see it.
?
For those that complain about video quality, I'm neither a youtuber nor a maker of fine videos.? It's worth every penny they paid for it.
?
I can sorta see why digirig doesn't want to mention the words "RA Board" because it's a competing product (as your "Wait!" quote in prior email illustrated).? And, perhaps (I dunno fer sher), because digirig decided on the CMedia chipset to leverage the software support already established by that competing product.? Totally don't know about that, but kinda makes sense.
?
It's all written out in the Digirig Lite Setup Manual: ?
?
They DO mention "RA Board" and "CMedia GPIO3" in the PTT section, though.
?
Hope that helps.
?
Re: MacBook OS and Failure to Transmit

 

Very nice video. I'm sure that some will criticize the sometimes fuzzy image, but it succinctly provides exactly what I wanted to know. I have recommended it to digirig in my discussion with them.

Also, fldigi has the same setting in Rig Control > C-Media PTT. I just didn't understand how it all works, in part because the fldigi manual itself mentions the boards, leaving me with the impression that I needed the board.

I don't have the lite, so I can't test this. But I wonder why digirig isn't more clear about this for the newbie, rather than drag in the board issue. That should be a footnote, not a main point.

Thanks for taking the time. Way more than I could have done, and a top notch answer.

73
~R~

On 2025-03-25 12:16:, W4MRP via groups.io wrote:
Re: MacBook OS and Failure to Transmit

 

Yes, you can use the digirig lite without anything extra.? With a HT and I assume any other radio for which you have digirig cables.
?
You don't need any other board.? No RA Board.? No DRA.??
?
I made a leeetle veeedio just for you to show it working in FLDIGI and Winlink/VARA-FM:
?
?
Hope that helps!
Re: FLRIG 2.0.05 and IC-7300 PTT/Transmit problems in CW #windows11 #cw #flrig #IC-7300

Anders Georgsson
 

ABSOLUTELY brilliant !!?
It works both in FLRIG and FLDIGI now!? Here are my software settings-the only change on the radio was to turn USB Keyer CW to DTR.
image.png

image.png

image.png

I greatly appreciate this help!? Anders / KZ4JN

On Mon, Mar 24, 2025 at 7:49?PM Rick Ellison via <rellison=[email protected]> wrote:
On the 7300 Click Menu then Set then Connectors The USB Send Keying What are your settings in that window???
On my 7300 I have:
USB SEND Off
USB Keying (CW) DTR
USB Keying (RTTY) Off

On your second sceenshot of the PTT settings under PTT on CAT Serial Port in the first dropdown box set that to None. On the CW Keyer under the config I have selected Use CAT and for Keyline I have DTR selected.
I can type in the window and it is sent and I can use the Macro buttons and they get sent also.

If you have been doing a lot of changes it might be helpful to go into the Flrig directory and delete the settings file.

73 Rick N2AMG


------ Original Message ------
From "Anders Georgsson via " <anders.georgsson@...>
Date 3/21/2025 11:11:36 AM
Subject [winfldigi] FLRIG 2.0.05 and IC-7300 PTT/Transmit problems in CW #cw #flrig #IC-7300 #windows11

I'm in the process of learning CW, using the MorseMania app and I'm doing really well on instant character recognition, but I have 0 sending skills at the moment.
?
I'd like to use FLRIG or FLDIGI to send CW but I'm having problems... when I use the CW Keyer in FLRIG, it doesn't trigger the IC-7300 to transmit?
If I use the same application to do FSK Keyer - it works fine...? And so does the "PTT" and "TUNE" button on the main FLRIG window...
?
Anyone have experiences with FLRIG and the IC-7300 CAT PTT? Here is how I have FLRIG configured:
?
?
Any and all reasonable suggestions are greatly appreciated ?
73 de KZ4JN


Virus-free.



--
Anders Georgsson
(352)316-0258 cell? KZ4JN/WSDF851
181 - 200 of 38102