开云体育

Well, that seem to check all the boxes. I assume you are using hamlib. The fact that it all works in admin mode is a puzzle. That means to me that you have all the gear set up correctly, but it sure

Hello Olirobin, An individial FAX image should look a bit like the attached one (but maybe in b/w ;-)... This is the typical size of such wx maps. The black bar visible at the top while receiving is

I dont think the com port is the issue.But the port is not in use. I can fire up WSJTX and it can connect on the same port (COM4). Exit WSJTRX and open DLDIGI - no com port 4.? I can see and change

WSJTX does find teh com port (COM4). Straight to the 7300 Same USB cable. I am using a tripplite with RF protection. How do I check for audio output stream? How do I know if the 7300 is commanded to

wsjtx

bonjour? ? ?? Hello, all the explanations are very good, I will try what you wrote to me to see if this phenomenon is reproduced or not.. I thank you for these explanations, hoping that it works

This is one of the side effects of "contests" and automation. Instead of folks actually sending and receiving code by hand, machines increasingly do the "work". Many hams don't realize how these side

Hi Mike, I didn't take part in the contest, but I listened to a few signals. A lot of contesters would send CQ at a highish speed followed by their call at say 18 wpm. In reply you'd get the

I'm having a problem with my fldigi (v4.2.06) and CW decoding. During the recent CQ WW DX CW contest, I used it (connected to the club's IC-7300) and more than 80-90% of the time, even on a fairly

Thanks so much mate. I am not sure exactly where these setting are though. I must be missing something Is it Configure - Config dialog then somewhere there? appreciate your help

Bonjour Olirobin, Thank you very much, that screenshot was very helpful! En fait, il y a un truc...! If you look at your image previews, the images are NOT stored as INDIVIDUAL files but as a

?Hello, the images are stored but the file weighs 0 bytes and cannot be opened. This is what it looks like in the storage directory. The two files at the top 73 to you. ? De : "T? via

Hello Olirobin, It is certainly a good idea to repeat the test using the latest stable version 4.2.06. Also, are all the images received during the 2 h properly stored as individual files? There

??Hello, thank you for answering me, here is the PC under Win 10 64 bits, on this PC it only runs HDSDR and FLDIGI in version 4.2.00.13 When decoding fax images from DDK2 etc. after about two

at http://www.w1hkj.com/alpha/flrig/ * flrig-2.0.05.85.tar.gz <http://www.w1hkj.com/alpha/flrig/flrig-2.0.05.85.tar.gz> * flrig-2.0.05.85_LI.dmg

Succinct and clear. Thanks for that. ~R~

KT, You did this backward. You only need the one installation of FLDIGI. Once you have it, make copies of the FLDIGI icon on your desktop or in a folder of your choice. THEN: For each icon, right

I need two different instances of FLDIGI.? I installed each into different Directories with their shortcuts into different folders.? I went to my ham install and setup some basic info and everything

So you can TX w WSJT=X? Well, that takes care of the permissions, I guess. Do they both use the same COM port? I assume the COM port is defined by the 7300. Does WSJT find it? Do you go straight to

Yes you do :-) Audio devices for input fall into the category of mics, so once installed, whether in use or not, {my understanding is that} the mic needs to be given permission to be in use. Not sure