|
All,
I have a MTR2000 here that I have interfaced to a USB-RIM module, I have it working in COS mode but want to run a ctcss code on it.
I was curious does anyone know if anything special needs to be set for the ctcss valid pin to go high to tell the RIM that the correct PL/ctcss is valid? I cant get the ctcss lead to go high to tell the RIM that there's a valid ctcss code. When I key up my handheld with the correct ctcss code on it it initially says keyed under the signal status.
Ive tried several mixtures of settings.
Under Audio I have Analog RX Activation set to PL
Under channel info I have decoder set to RX PL of 67.0
I am using the ICS-CTRL MTR2000 Adapter board that goes to a DB9. Its pulling from C2 for PL Detect & B4 for COR.
Thanks!
--Don
|
Wildcard programmed in the MTR? I take it you're using a transistor inverter to talk to the USB which normally requires a low going signal?
Chris WB5ITT
On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via <dwisdom-lists= [email protected]> wrote: All,
I have a MTR2000 here that I have interfaced to a USB-RIM module, I have
it working in COS mode but want to run a ctcss code on it.
I was curious does anyone know if anything special needs to be set for
the ctcss valid pin to go high to tell the RIM that the correct PL/ctcss
is valid?? I cant get the ctcss lead to go high to tell the RIM that
there's a valid ctcss code.? When I key up my handheld with the correct
ctcss code on it it initially says keyed under the signal status.
Ive tried several mixtures of settings.
Under Audio I have Analog RX Activation set to PL
Under channel info I have decoder set to RX PL of 67.0
I am using the ICS-CTRL MTR2000 Adapter board that goes to a DB9.? Its
pulling from C2 for PL Detect & B4 for COR.
Thanks!
--Don
|
Hi Chris,
The USB-RIM is set to use an active high signal for both COS and CTCSS. I have the PL line set in the wildcard however I just noticed that there isnt a output for pin C2 in the output group settings. There is an output for pin C4.
Other thing the wildcard checkbox is greyed out on the system configuration screen.
Thanks
--Don
toggle quoted message
Show quoted text
On 3/11/25 04:37, Chris Boone WB5ITT via groups.io wrote: Wildcard programmed in the MTR? I take it you're using a transistor inverter to talk to the USB which normally requires a low going signal?
Chris WB5ITT
On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via groups.io < groups.io> <dwisdom-lists@... <mailto:[email protected]>> wrote:
All,
I have a MTR2000 here that I have interfaced to a USB-RIM module, I
have
it working in COS mode but want to run a ctcss code on it.
I was curious does anyone know if anything special needs to be set for
the ctcss valid pin to go high to tell the RIM that the correct PL/
ctcss
is valid?? I cant get the ctcss lead to go high to tell the RIM that
there's a valid ctcss code.? When I key up my handheld with the correct
ctcss code on it it initially says keyed under the signal status.
Ive tried several mixtures of settings.
Under Audio I have Analog RX Activation set to PL
Under channel info I have decoder set to RX PL of 67.0
I am using the ICS-CTRL MTR2000 Adapter board that goes to a DB9.? Its
pulling from C2 for PL Detect & B4 for COR.
Thanks!
--Don
------------------------------------------------------------------------
This email has been scanned for spam and viruses by Proofpoint Essentials. Click here < report_spam.php? mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f577f6a7f4e1a88ac1d47bcf2c53d3807385ae2230f669c04048c6c78d9bac1307256a11a78a76a955c538c168c47ac2eb53d690026f4a2a3b24ef7fa5b3911d564f8dbe210224514c9cc909bd3d3be91e95469ebc24d1ea94a992d70e93442cfe28dfa80f47b21b1e16199b16adabd4cc8359d84e790de32176bacd6b6cc60ea079127f6ade61e1518c4bd5e858013e0363796f47a18b838> to report this email as spam.
|
Chris,
other thing too, I looked at the station operation controls and briefly rx mode says active then switches back to inactive.
Thanks
--Don
toggle quoted message
Show quoted text
On 3/11/25 17:14, Don Wisdom KD7WKF via groups.io wrote: Hi Chris,
The USB-RIM is set to use an active high signal for both COS and CTCSS. ?I have the PL line set in the wildcard however I just noticed that there isnt a output for pin C2 in the output group settings.? There is an output for pin C4.
Other thing the wildcard checkbox is greyed out on the system configuration screen.
Thanks
--Don
On 3/11/25 04:37, Chris Boone WB5ITT via groups.io wrote:
Wildcard programmed in the MTR? I take it you're using a transistor inverter to talk to the USB which normally requires a low going signal?
Chris WB5ITT
On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via groups.io < groups.io> <dwisdom-lists@... <mailto:[email protected]>> wrote:
??? All,
??? I have a MTR2000 here that I have interfaced to a USB-RIM module, I
??? have
??? it working in COS mode but want to run a ctcss code on it.
??? I was curious does anyone know if anything special needs to be set for
??? the ctcss valid pin to go high to tell the RIM that the correct PL/
??? ctcss
??? is valid?? I cant get the ctcss lead to go high to tell the RIM that
??? there's a valid ctcss code.? When I key up my handheld with the correct
??? ctcss code on it it initially says keyed under the signal status.
??? Ive tried several mixtures of settings.
??? Under Audio I have Analog RX Activation set to PL
??? Under channel info I have decoder set to RX PL of 67.0
??? I am using the ICS-CTRL MTR2000 Adapter board that goes to a DB9. Its
??? pulling from C2 for PL Detect & B4 for COR.
??? Thanks!
??? --Don
------------------------------------------------------------------------
This email has been scanned for spam and viruses by Proofpoint Essentials. Click here < report_spam.php? mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f577f6a7f4e1a88ac1d47bcf2c53d3807385ae2230f669c04048c6c78d9bac1307256a11a78a76a955c538c168c47ac2eb53d690026f4a2a3b24ef7fa5b3911d564f8dbe210224514c9cc909bd3d3be91e95469ebc24d1ea94a992d70e93442cfe28dfa80f47b21b1e16199b16adabd4cc8359d84e790de32176bacd6b6cc60ea079127f6ade61e1518c4bd5e858013e0363796f47a18b838> to report this email as spam.
----------
This email has been scanned for spam and viruses by Proofpoint Essentials. Visit the following link to report this email as spam:
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fc124d7e359c0d931f2618bd4777537955025669c4cf03fbe99daf3923a58ea73990e0d86747fc4d1b18ff00d2263c17201ddcec68a653397c319c237ef69e76f78ed58917ce4e103b50f0eb39c5640e327fd772d2ec5d79d5e79df9ca63b9a86ac2d84a5e79c87925a3595804ba1925c02312a0f20980ca0555e4fcb2c18f1b089368b4c847fd1f79a210fa75aeca9c2f7135b3aaa366784
|
All,
I redid the codeplug from scratch and off it went!
Thanks!
--Don
toggle quoted message
Show quoted text
On 3/11/25 17:50, Don Wisdom KD7WKF via groups.io wrote: Chris,
other thing too, I looked at the station operation controls and briefly rx mode says active then switches back to inactive.
Thanks
--Don
On 3/11/25 17:14, Don Wisdom KD7WKF via groups.io wrote:
Hi Chris,
The USB-RIM is set to use an active high signal for both COS and CTCSS. ??I have the PL line set in the wildcard however I just noticed that there isnt a output for pin C2 in the output group settings. There is an output for pin C4.
Other thing the wildcard checkbox is greyed out on the system configuration screen.
Thanks
--Don
On 3/11/25 04:37, Chris Boone WB5ITT via groups.io wrote:
Wildcard programmed in the MTR? I take it you're using a transistor inverter to talk to the USB which normally requires a low going signal?
Chris WB5ITT
On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via groups.io < groups.io> <dwisdom-lists@... <mailto:[email protected]>> wrote:
??? All,
??? I have a MTR2000 here that I have interfaced to a USB-RIM module, I
??? have
??? it working in COS mode but want to run a ctcss code on it.
??? I was curious does anyone know if anything special needs to be set for
??? the ctcss valid pin to go high to tell the RIM that the correct PL/
??? ctcss
??? is valid?? I cant get the ctcss lead to go high to tell the RIM that
??? there's a valid ctcss code.? When I key up my handheld with the correct
??? ctcss code on it it initially says keyed under the signal status.
??? Ive tried several mixtures of settings.
??? Under Audio I have Analog RX Activation set to PL
??? Under channel info I have decoder set to RX PL of 67.0
??? I am using the ICS-CTRL MTR2000 Adapter board that goes to a DB9. Its
??? pulling from C2 for PL Detect & B4 for COR.
??? Thanks!
??? --Don
------------------------------------------------------------------------
This email has been scanned for spam and viruses by Proofpoint Essentials. Click here < report_spam.php? mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f577f6a7f4e1a88ac1d47bcf2c53d3807385ae2230f669c04048c6c78d9bac1307256a11a78a76a955c538c168c47ac2eb53d690026f4a2a3b24ef7fa5b3911d564f8dbe210224514c9cc909bd3d3be91e95469ebc24d1ea94a992d70e93442cfe28dfa80f47b21b1e16199b16adabd4cc8359d84e790de32176bacd6b6cc60ea079127f6ade61e1518c4bd5e858013e0363796f47a18b838> to report this email as spam.
----------
This email has been scanned for spam and viruses by Proofpoint Essentials. Visit the following link to report this email as spam:
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fc124d7e359c0d931f2618bd4777537955025669c4cf03fbe99daf3923a58ea73990e0d86747fc4d1b18ff00d2263c17201ddcec68a653397c319c237ef69e76f78ed58917ce4e103b50f0eb39c5640e327fd772d2ec5d79d5e79df9ca63b9a86ac2d84a5e79c87925a3595804ba1925c02312a0f20980ca0555e4fcb2c18f1b089368b4c847fd1f79a210fa75aeca9c2f7135b3aaa366784
----------
This email has been scanned for spam and viruses by Proofpoint Essentials. Visit the following link to report this email as spam:
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f6725180200ff49e6d753862a952d3867fbc6f5fe2e9e45705148e8e30859920fde9ceff2211e585aaf2265ab029c0d0b40090765fef6ae20dc2d4bdcd027f592db12b9b429de9de779b55cf175a013dfe33f0015ad9bc8b7ad9583f0810356fa3797bf5ce12a4a46631b36bda83b988d84421fc44e088725e2d167c92a1c677e909d7499a35e542e0d72793b2f5c9dfe84ebda61eba7d88a
|
Chris,
Unfortunately a reboot caused the issue came back :(
Its still switching to Active then back to inactive on reciever rx mode.
Thanks
--Don
toggle quoted message
Show quoted text
On 3/11/25 18:18, Don Wisdom KD7WKF via groups.io wrote: All,
I redid the codeplug from scratch and off it went!
Thanks!
--Don
On 3/11/25 17:50, Don Wisdom KD7WKF via groups.io wrote:
Chris,
other thing too, I looked at the station operation controls and briefly rx mode says active then switches back to inactive.
Thanks
--Don
On 3/11/25 17:14, Don Wisdom KD7WKF via groups.io wrote:
Hi Chris,
The USB-RIM is set to use an active high signal for both COS and CTCSS. ??I have the PL line set in the wildcard however I just noticed that there isnt a output for pin C2 in the output group settings. There is an output for pin C4.
Other thing the wildcard checkbox is greyed out on the system configuration screen.
Thanks
--Don
On 3/11/25 04:37, Chris Boone WB5ITT via groups.io wrote:
Wildcard programmed in the MTR? I take it you're using a transistor inverter to talk to the USB which normally requires a low going signal?
Chris WB5ITT
On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via groups.io < groups.io> <dwisdom-lists@... <mailto:[email protected]>> wrote:
??? All,
??? I have a MTR2000 here that I have interfaced to a USB-RIM module, I
??? have
??? it working in COS mode but want to run a ctcss code on it.
??? I was curious does anyone know if anything special needs to be set for
??? the ctcss valid pin to go high to tell the RIM that the correct PL/
??? ctcss
??? is valid?? I cant get the ctcss lead to go high to tell the RIM that
??? there's a valid ctcss code.? When I key up my handheld with the correct
??? ctcss code on it it initially says keyed under the signal status.
??? Ive tried several mixtures of settings.
??? Under Audio I have Analog RX Activation set to PL
??? Under channel info I have decoder set to RX PL of 67.0
??? I am using the ICS-CTRL MTR2000 Adapter board that goes to a DB9. Its
??? pulling from C2 for PL Detect & B4 for COR.
??? Thanks!
??? --Don
------------------------------------------------------------------------
This email has been scanned for spam and viruses by Proofpoint Essentials. Click here < report_spam.php? mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f577f6a7f4e1a88ac1d47bcf2c53d3807385ae2230f669c04048c6c78d9bac1307256a11a78a76a955c538c168c47ac2eb53d690026f4a2a3b24ef7fa5b3911d564f8dbe210224514c9cc909bd3d3be91e95469ebc24d1ea94a992d70e93442cfe28dfa80f47b21b1e16199b16adabd4cc8359d84e790de32176bacd6b6cc60ea079127f6ade61e1518c4bd5e858013e0363796f47a18b838> to report this email as spam.
----------
This email has been scanned for spam and viruses by Proofpoint Essentials. Visit the following link to report this email as spam:
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fc124d7e359c0d931f2618bd4777537955025669c4cf03fbe99daf3923a58ea73990e0d86747fc4d1b18ff00d2263c17201ddcec68a653397c319c237ef69e76f78ed58917ce4e103b50f0eb39c5640e327fd772d2ec5d79d5e79df9ca63b9a86ac2d84a5e79c87925a3595804ba1925c02312a0f20980ca0555e4fcb2c18f1b089368b4c847fd1f79a210fa75aeca9c2f7135b3aaa366784
----------
This email has been scanned for spam and viruses by Proofpoint Essentials. Visit the following link to report this email as spam:
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f6725180200ff49e6d753862a952d3867fbc6f5fe2e9e45705148e8e30859920fde9ceff2211e585aaf2265ab029c0d0b40090765fef6ae20dc2d4bdcd027f592db12b9b429de9de779b55cf175a013dfe33f0015ad9bc8b7ad9583f0810356fa3797bf5ce12a4a46631b36bda83b988d84421fc44e088725e2d167c92a1c677e909d7499a35e542e0d72793b2f5c9dfe84ebda61eba7d88a
----------
This email has been scanned for spam and viruses by Proofpoint Essentials. Visit the following link to report this email as spam:
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f70b21e8aa391eefe5ee7142dd8f96ba22d1f4618be664d15513c560e70a41371b663fac156aa3fc86aa5ec93d9dada30e0f39465616b0661d72a1da240e5f7ddbf79c939dd1ac26c82c32c000343ea751ef490198d541a77c5578db5017c5206b2aae876bfe58817ccf7c9723820fc7a10f41bcc939b232c42919f681e805d77c41496c5140f22adc089eece3c2012839e87137296a143f3
|
I'm starting to work on a similar setup...would you be willing to share the codeplug file?
Don
On Tue, Mar 11, 2025, 5:18 PM Don Wisdom KD7WKF via <dwisdom-lists= [email protected]> wrote: All,
I redid the codeplug from scratch and off it went!
Thanks!
--Don
On 3/11/25 17:50, Don Wisdom KD7WKF via wrote:
> Chris,
>
> other thing too, I looked at the station operation controls and briefly
> rx mode says active then switches back to inactive.
>
> Thanks
>
> --Don
>
>
> On 3/11/25 17:14, Don Wisdom KD7WKF via wrote:
>> Hi Chris,
>>
>> The USB-RIM is set to use an active high signal for both COS and
>> CTCSS. ??I have the PL line set in the wildcard however I just noticed
>> that there isnt a output for pin C2 in the output group settings.?
>> There is an output for pin C4.
>>
>> Other thing the wildcard checkbox is greyed out on the system
>> configuration screen.
>>
>> Thanks
>>
>> --Don
>>
>>
>> On 3/11/25 04:37, Chris Boone WB5ITT via wrote:
>>> Wildcard programmed in the MTR? I take it you're using a transistor
>>> inverter to talk to the USB which normally requires a low going signal?
>>>
>>> Chris WB5ITT
>>>
>>>
>>> On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via
>>> <http:// > <dwisdom-lists=[email protected]
>>> <mailto:[email protected]>> wrote:
>>>
>>> ??? All,
>>>
>>> ??? I have a MTR2000 here that I have interfaced to a USB-RIM module, I
>>> ??? have
>>> ??? it working in COS mode but want to run a ctcss code on it.
>>>
>>> ??? I was curious does anyone know if anything special needs to be
>>> set for
>>> ??? the ctcss valid pin to go high to tell the RIM that the correct PL/
>>> ??? ctcss
>>> ??? is valid?? I cant get the ctcss lead to go high to tell the RIM that
>>> ??? there's a valid ctcss code.? When I key up my handheld with the
>>> correct
>>> ??? ctcss code on it it initially says keyed under the signal status.
>>>
>>> ??? Ive tried several mixtures of settings.
>>>
>>> ??? Under Audio I have Analog RX Activation set to PL
>>>
>>> ??? Under channel info I have decoder set to RX PL of 67.0
>>>
>>> ??? I am using the ICS-CTRL MTR2000 Adapter board that goes to a DB9.
>>> Its
>>> ??? pulling from C2 for PL Detect & B4 for COR.
>>>
>>> ??? Thanks!
>>>
>>> ??? --Don
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>> ------------------------------------------------------------------------
>>>
>>> This email has been scanned for spam and viruses by Proofpoint
>>> Essentials. Click here <
>>> report_spam.php?
>>> mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f577f6a7f4e1a88ac1d47bcf2c53d3807385ae2230f669c04048c6c78d9bac1307256a11a78a76a955c538c168c47ac2eb53d690026f4a2a3b24ef7fa5b3911d564f8dbe210224514c9cc909bd3d3be91e95469ebc24d1ea94a992d70e93442cfe28dfa80f47b21b1e16199b16adabd4cc8359d84e790de32176bacd6b6cc60ea079127f6ade61e1518c4bd5e858013e0363796f47a18b838> to report this email as spam.
>>>
>>>
>>
>>
>>
>>
>>
>>
>>
>> ----------
>>
>> This email has been scanned for spam and viruses by Proofpoint
>> Essentials. Visit the following link to report this email as spam:
>> ?
>> mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fc124d7e359c0d931f2618bd4777537955025669c4cf03fbe99daf3923a58ea73990e0d86747fc4d1b18ff00d2263c17201ddcec68a653397c319c237ef69e76f78ed58917ce4e103b50f0eb39c5640e327fd772d2ec5d79d5e79df9ca63b9a86ac2d84a5e79c87925a3595804ba1925c02312a0f20980ca0555e4fcb2c18f1b089368b4c847fd1f79a210fa75aeca9c2f7135b3aaa366784
>>
>
>
>
>
>
>
>
> ----------
>
> This email has been scanned for spam and viruses by Proofpoint
> Essentials. Visit the following link to report this email as spam:
> ?
> mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f6725180200ff49e6d753862a952d3867fbc6f5fe2e9e45705148e8e30859920fde9ceff2211e585aaf2265ab029c0d0b40090765fef6ae20dc2d4bdcd027f592db12b9b429de9de779b55cf175a013dfe33f0015ad9bc8b7ad9583f0810356fa3797bf5ce12a4a46631b36bda83b988d84421fc44e088725e2d167c92a1c677e909d7499a35e542e0d72793b2f5c9dfe84ebda61eba7d88a
>
|
Sure, Ill email it too you directly now however its not working again :(
toggle quoted message
Show quoted text
On 3/11/25 18:40, dsay2001 via groups.io wrote: I'm starting to work on a similar setup...would you be willing to share the codeplug file?
Don
On Tue, Mar 11, 2025, 5:18 PM Don Wisdom KD7WKF via groups.io < groups.io> <dwisdom-lists@... <mailto:[email protected]>> wrote:
All,
I redid the codeplug from scratch and off it went!
Thanks!
--Don
On 3/11/25 17:50, Don Wisdom KD7WKF via groups.io <>
wrote:
> Chris,
>
> other thing too, I looked at the station operation controls and
briefly
> rx mode says active then switches back to inactive.
>
> Thanks
>
> --Don
>
>
> On 3/11/25 17:14, Don Wisdom KD7WKF via groups.io <
groups.io> wrote:
>> Hi Chris,
>>
>> The USB-RIM is set to use an active high signal for both COS and
>> CTCSS. ??I have the PL line set in the wildcard however I just
noticed
>> that there isnt a output for pin C2 in the output group settings.
>> There is an output for pin C4.
>>
>> Other thing the wildcard checkbox is greyed out on the system
>> configuration screen.
>>
>> Thanks
>>
>> --Don
>>
>>
>> On 3/11/25 04:37, Chris Boone WB5ITT via groups.io <
groups.io> wrote:
>>> Wildcard programmed in the MTR? I take it you're using a
transistor
>>> inverter to talk to the USB which normally requires a low going
signal?
>>>
>>> Chris WB5ITT
>>>
>>>
>>> On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via groups.io
<>
>>> < groups.io <>> <dwisdom-
lists@... <mailto:[email protected]>
>>> <mailto:[email protected] <mailto:[email protected]>>>
wrote:
>>>
>>> ??? All,
>>>
>>> ??? I have a MTR2000 here that I have interfaced to a USB-RIM
module, I
>>> ??? have
>>> ??? it working in COS mode but want to run a ctcss code on it.
>>>
>>> ??? I was curious does anyone know if anything special needs to be
>>> set for
>>> ??? the ctcss valid pin to go high to tell the RIM that the
correct PL/
>>> ??? ctcss
>>> ??? is valid?? I cant get the ctcss lead to go high to tell the
RIM that
>>> ??? there's a valid ctcss code.? When I key up my handheld with
the
>>> correct
>>> ??? ctcss code on it it initially says keyed under the signal
status.
>>>
>>> ??? Ive tried several mixtures of settings.
>>>
>>> ??? Under Audio I have Analog RX Activation set to PL
>>>
>>> ??? Under channel info I have decoder set to RX PL of 67.0
>>>
>>> ??? I am using the ICS-CTRL MTR2000 Adapter board that goes to
a DB9.
>>> Its
>>> ??? pulling from C2 for PL Detect & B4 for COR.
>>>
>>> ??? Thanks!
>>>
>>> ??? --Don
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
------------------------------------------------------------------------
>>>
>>> This email has been scanned for spam and viruses by Proofpoint
>>> Essentials. Click here <
app/ <>
>>> report_spam.php?
>>>
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f577f6a7f4e1a88ac1d47bcf2c53d3807385ae2230f669c04048c6c78d9bac1307256a11a78a76a955c538c168c47ac2eb53d690026f4a2a3b24ef7fa5b3911d564f8dbe210224514c9cc909bd3d3be91e95469ebc24d1ea94a992d70e93442cfe28dfa80f47b21b1e16199b16adabd4cc8359d84e790de32176bacd6b6cc60ea079127f6ade61e1518c4bd5e858013e0363796f47a18b838> to report this email as spam.
>>>
>>>
>>
>>
>>
>>
>>
>>
>>
>> ----------
>>
>> This email has been scanned for spam and viruses by Proofpoint
>> Essentials. Visit the following link to report this email as spam:
>>
<>?
>>
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fc124d7e359c0d931f2618bd4777537955025669c4cf03fbe99daf3923a58ea73990e0d86747fc4d1b18ff00d2263c17201ddcec68a653397c319c237ef69e76f78ed58917ce4e103b50f0eb39c5640e327fd772d2ec5d79d5e79df9ca63b9a86ac2d84a5e79c87925a3595804ba1925c02312a0f20980ca0555e4fcb2c18f1b089368b4c847fd1f79a210fa75aeca9c2f7135b3aaa366784
>>
>
>
>
>
>
>
>
> ----------
>
> This email has been scanned for spam and viruses by Proofpoint
> Essentials. Visit the following link to report this email as spam:
>
<>?
>
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f6725180200ff49e6d753862a952d3867fbc6f5fe2e9e45705148e8e30859920fde9ceff2211e585aaf2265ab029c0d0b40090765fef6ae20dc2d4bdcd027f592db12b9b429de9de779b55cf175a013dfe33f0015ad9bc8b7ad9583f0810356fa3797bf5ce12a4a46631b36bda83b988d84421fc44e088725e2d167c92a1c677e909d7499a35e542e0d72793b2f5c9dfe84ebda61eba7d88a
>
------------------------------------------------------------------------
This email has been scanned for spam and viruses by Proofpoint Essentials. Click here < report_spam.php? mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fee34ff1a185c1d35060d41d9e67985d4ae98901ed6bbeeb13416feec750e1dca4256c6e581eb51fb6e812ec19c124f543296b38ad13df1c0f78a4d3db07e5b43a18bc0d2b8dd326d45d36a4c07ad46ece63c6acd3909dab3f41b9f44dd331933fcf71c3405ee9a27e78d1b510db6acd1944de2b04b0960a785665afc0097d15e4be3048d03c8da6718c6a412ea49b255e2644e5b3fe1e5a4> to report this email as spam.
|
All,
To let everyone know what I figured out (and aid others), there are TWO places you have to set the radio to full duplex if you have a wireline card installed, there's the settings on station config *AND* on the wireline config.? It will do exactly as it was doing if the radio is set to full duplex but wireline is set to half duplex.
Thanks
--Don
toggle quoted message
Show quoted text
On 3/11/25 18:43, Don Wisdom KD7WKF via groups.io wrote: Sure, Ill email it too you directly now however its not working again :(
On 3/11/25 18:40, dsay2001 via groups.io wrote:
I'm starting to work on a similar setup...would you be willing to share the codeplug file?
Don
On Tue, Mar 11, 2025, 5:18 PM Don Wisdom KD7WKF via groups.io < groups.io> <dwisdom-lists@... <mailto:[email protected]>> wrote:
??? All,
??? I redid the codeplug from scratch and off it went!
??? Thanks!
??? --Don
??? On 3/11/25 17:50, Don Wisdom KD7WKF via groups.io <>
??? wrote:
???? > Chris,
???? >
???? > other thing too, I looked at the station operation controls and
??? briefly
???? > rx mode says active then switches back to inactive.
???? >
???? > Thanks
???? >
???? > --Don
???? >
???? >
???? > On 3/11/25 17:14, Don Wisdom KD7WKF via groups.io <
??? groups.io> wrote:
???? >> Hi Chris,
???? >>
???? >> The USB-RIM is set to use an active high signal for both COS and
???? >> CTCSS. ??I have the PL line set in the wildcard however I just
??? noticed
???? >> that there isnt a output for pin C2 in the output group settings.
???? >> There is an output for pin C4.
???? >>
???? >> Other thing the wildcard checkbox is greyed out on the system
???? >> configuration screen.
???? >>
???? >> Thanks
???? >>
???? >> --Don
???? >>
???? >>
???? >> On 3/11/25 04:37, Chris Boone WB5ITT via groups.io <
??? groups.io> wrote:
???? >>> Wildcard programmed in the MTR? I take it you're using a
??? transistor
???? >>> inverter to talk to the USB which normally requires a low going
??? signal?
???? >>>
???? >>> Chris WB5ITT
???? >>>
???? >>>
???? >>> On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via groups.io
??? <>
???? >>> < groups.io <>> <dwisdom-
??? lists@... <mailto:[email protected]>
???? >>> <mailto:[email protected] <mailto:[email protected]>>>
??? wrote:
???? >>>
???? >>> ??? All,
???? >>>
???? >>> ??? I have a MTR2000 here that I have interfaced to a USB-RIM
??? module, I
???? >>> ??? have
???? >>> ??? it working in COS mode but want to run a ctcss code on it.
???? >>>
???? >>> ??? I was curious does anyone know if anything special needs to be
???? >>> set for
???? >>> ??? the ctcss valid pin to go high to tell the RIM that the
??? correct PL/
???? >>> ??? ctcss
???? >>> ??? is valid?? I cant get the ctcss lead to go high to tell the
??? RIM that
???? >>> ??? there's a valid ctcss code.? When I key up my handheld with
??? the
???? >>> correct
???? >>> ??? ctcss code on it it initially says keyed under the signal
??? status.
???? >>>
???? >>> ??? Ive tried several mixtures of settings.
???? >>>
???? >>> ??? Under Audio I have Analog RX Activation set to PL
???? >>>
???? >>> ??? Under channel info I have decoder set to RX PL of 67.0
???? >>>
???? >>> ??? I am using the ICS-CTRL MTR2000 Adapter board that goes to
??? a DB9.
???? >>> Its
???? >>> ??? pulling from C2 for PL Detect & B4 for COR.
???? >>>
???? >>> ??? Thanks!
???? >>>
???? >>> ??? --Don
???? >>>
???? >>>
???? >>>
???? >>>
???? >>>
???? >>>
???? >>>
???? >>>
???? >>>
------------------------------------------------------------------------
???? >>>
???? >>> This email has been scanned for spam and viruses by Proofpoint
???? >>> Essentials. Click here <
??? app/ <>
???? >>> report_spam.php?
???? >>>
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f577f6a7f4e1a88ac1d47bcf2c53d3807385ae2230f669c04048c6c78d9bac1307256a11a78a76a955c538c168c47ac2eb53d690026f4a2a3b24ef7fa5b3911d564f8dbe210224514c9cc909bd3d3be91e95469ebc24d1ea94a992d70e93442cfe28dfa80f47b21b1e16199b16adabd4cc8359d84e790de32176bacd6b6cc60ea079127f6ade61e1518c4bd5e858013e0363796f47a18b838> to report this email as spam.
???? >>>
???? >>>
???? >>
???? >>
???? >>
???? >>
???? >>
???? >>
???? >>
???? >> ----------
???? >>
???? >> This email has been scanned for spam and viruses by Proofpoint
???? >> Essentials. Visit the following link to report this email as spam:
???? >>
<>?
???? >>
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fc124d7e359c0d931f2618bd4777537955025669c4cf03fbe99daf3923a58ea73990e0d86747fc4d1b18ff00d2263c17201ddcec68a653397c319c237ef69e76f78ed58917ce4e103b50f0eb39c5640e327fd772d2ec5d79d5e79df9ca63b9a86ac2d84a5e79c87925a3595804ba1925c02312a0f20980ca0555e4fcb2c18f1b089368b4c847fd1f79a210fa75aeca9c2f7135b3aaa366784
???? >>
???? >
???? >
???? >
???? >
???? >
???? >
???? >
???? > ----------
???? >
???? > This email has been scanned for spam and viruses by Proofpoint
???? > Essentials. Visit the following link to report this email as spam:
???? >
<>?
???? >
mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f6725180200ff49e6d753862a952d3867fbc6f5fe2e9e45705148e8e30859920fde9ceff2211e585aaf2265ab029c0d0b40090765fef6ae20dc2d4bdcd027f592db12b9b429de9de779b55cf175a013dfe33f0015ad9bc8b7ad9583f0810356fa3797bf5ce12a4a46631b36bda83b988d84421fc44e088725e2d167c92a1c677e909d7499a35e542e0d72793b2f5c9dfe84ebda61eba7d88a
???? >
------------------------------------------------------------------------
This email has been scanned for spam and viruses by Proofpoint Essentials. Click here < report_spam.php? mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fee34ff1a185c1d35060d41d9e67985d4ae98901ed6bbeeb13416feec750e1dca4256c6e581eb51fb6e812ec19c124f543296b38ad13df1c0f78a4d3db07e5b43a18bc0d2b8dd326d45d36a4c07ad46ece63c6acd3909dab3f41b9f44dd331933fcf71c3405ee9a27e78d1b510db6acd1944de2b04b0960a785665afc0097d15e4be3048d03c8da6718c6a412ea49b255e2644e5b3fe1e5a4> to report this email as spam.
----------
This email has been scanned for spam and viruses by Proofpoint Essentials. Visit the following link to report this email as spam:
|
Hi
Can you please share the places of the configs ??
Take care
73s ct2gnh - Paulo Lobo Don Wisdom KD7WKF via <dwisdom-lists= [email protected]> escreveu (quinta, 13/03/2025 à(s) 14:46):
All,
To let everyone know what I figured out (and aid others), there are TWO
places you have to set the radio to full duplex if you have a wireline
card installed, there's the settings on station config *AND* on the
wireline config.? It will do exactly as it was doing if the radio is set
to full duplex but wireline is set to half duplex.
Thanks
--Don
On 3/11/25 18:43, Don Wisdom KD7WKF via wrote:
> Sure, Ill email it too you directly now however its not working again :(
>
>
> On 3/11/25 18:40, dsay2001 via wrote:
>> I'm starting to work on a similar setup...would you be willing to
>> share the codeplug file?
>>
>> Don
>>
>> On Tue, Mar 11, 2025, 5:18 PM Don Wisdom KD7WKF via
>> <http:// > <dwisdom-lists=[email protected]
>> <mailto:[email protected]>> wrote:
>>
>> ??? All,
>>
>> ??? I redid the codeplug from scratch and off it went!
>>
>> ??? Thanks!
>>
>> ??? --Don
>>
>>
>> ??? On 3/11/25 17:50, Don Wisdom KD7WKF via <>
>> ??? wrote:
>> ???? > Chris,
>> ???? >
>> ???? > other thing too, I looked at the station operation controls and
>> ??? briefly
>> ???? > rx mode says active then switches back to inactive.
>> ???? >
>> ???? > Thanks
>> ???? >
>> ???? > --Don
>> ???? >
>> ???? >
>> ???? > On 3/11/25 17:14, Don Wisdom KD7WKF via <http://
>> ??? > wrote:
>> ???? >> Hi Chris,
>> ???? >>
>> ???? >> The USB-RIM is set to use an active high signal for both COS and
>> ???? >> CTCSS. ??I have the PL line set in the wildcard however I just
>> ??? noticed
>> ???? >> that there isnt a output for pin C2 in the output group
>> settings.
>> ???? >> There is an output for pin C4.
>> ???? >>
>> ???? >> Other thing the wildcard checkbox is greyed out on the system
>> ???? >> configuration screen.
>> ???? >>
>> ???? >> Thanks
>> ???? >>
>> ???? >> --Don
>> ???? >>
>> ???? >>
>> ???? >> On 3/11/25 04:37, Chris Boone WB5ITT via <http://
>> ??? > wrote:
>> ???? >>> Wildcard programmed in the MTR? I take it you're using a
>> ??? transistor
>> ???? >>> inverter to talk to the USB which normally requires a low going
>> ??? signal?
>> ???? >>>
>> ???? >>> Chris WB5ITT
>> ???? >>>
>> ???? >>>
>> ???? >>> On Mon, Mar 10, 2025, 7:48 PM Don Wisdom KD7WKF via
>> ??? <>
>> ???? >>> <http:// <>> <dwisdom-
>> ??? lists=[email protected] <mailto:[email protected]>
>> ???? >>> <mailto:[email protected] <mailto:[email protected]>>>
>> ??? wrote:
>> ???? >>>
>> ???? >>> ??? All,
>> ???? >>>
>> ???? >>> ??? I have a MTR2000 here that I have interfaced to a USB-RIM
>> ??? module, I
>> ???? >>> ??? have
>> ???? >>> ??? it working in COS mode but want to run a ctcss code on it.
>> ???? >>>
>> ???? >>> ??? I was curious does anyone know if anything special needs
>> to be
>> ???? >>> set for
>> ???? >>> ??? the ctcss valid pin to go high to tell the RIM that the
>> ??? correct PL/
>> ???? >>> ??? ctcss
>> ???? >>> ??? is valid?? I cant get the ctcss lead to go high to tell the
>> ??? RIM that
>> ???? >>> ??? there's a valid ctcss code.? When I key up my handheld with
>> ??? the
>> ???? >>> correct
>> ???? >>> ??? ctcss code on it it initially says keyed under the signal
>> ??? status.
>> ???? >>>
>> ???? >>> ??? Ive tried several mixtures of settings.
>> ???? >>>
>> ???? >>> ??? Under Audio I have Analog RX Activation set to PL
>> ???? >>>
>> ???? >>> ??? Under channel info I have decoder set to RX PL of 67.0
>> ???? >>>
>> ???? >>> ??? I am using the ICS-CTRL MTR2000 Adapter board that goes to
>> ??? a DB9.
>> ???? >>> Its
>> ???? >>> ??? pulling from C2 for PL Detect & B4 for COR.
>> ???? >>>
>> ???? >>> ??? Thanks!
>> ???? >>>
>> ???? >>> ??? --Don
>> ???? >>>
>> ???? >>>
>> ???? >>>
>> ???? >>>
>> ???? >>>
>> ???? >>>
>> ???? >>>
>> ???? >>>
>> ???? >>>
>> ------------------------------------------------------------------------
>> ???? >>>
>> ???? >>> This email has been scanned for spam and viruses by Proofpoint
>> ???? >>> Essentials. Click here <
>> ??? app/ <>
>> ???? >>> report_spam.php?
>> ???? >>>
>> mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f577f6a7f4e1a88ac1d47bcf2c53d3807385ae2230f669c04048c6c78d9bac1307256a11a78a76a955c538c168c47ac2eb53d690026f4a2a3b24ef7fa5b3911d564f8dbe210224514c9cc909bd3d3be91e95469ebc24d1ea94a992d70e93442cfe28dfa80f47b21b1e16199b16adabd4cc8359d84e790de32176bacd6b6cc60ea079127f6ade61e1518c4bd5e858013e0363796f47a18b838>
>> to report this email as spam.
>> ???? >>>
>> ???? >>>
>> ???? >>
>> ???? >>
>> ???? >>
>> ???? >>
>> ???? >>
>> ???? >>
>> ???? >>
>> ???? >> ----------
>> ???? >>
>> ???? >> This email has been scanned for spam and viruses by Proofpoint
>> ???? >> Essentials. Visit the following link to report this email as
>> spam:
>> ???? >>
>> <>?
>> ???? >>
>> mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fc124d7e359c0d931f2618bd4777537955025669c4cf03fbe99daf3923a58ea73990e0d86747fc4d1b18ff00d2263c17201ddcec68a653397c319c237ef69e76f78ed58917ce4e103b50f0eb39c5640e327fd772d2ec5d79d5e79df9ca63b9a86ac2d84a5e79c87925a3595804ba1925c02312a0f20980ca0555e4fcb2c18f1b089368b4c847fd1f79a210fa75aeca9c2f7135b3aaa366784
>> ???? >>
>> ???? >
>> ???? >
>> ???? >
>> ???? >
>> ???? >
>> ???? >
>> ???? >
>> ???? > ----------
>> ???? >
>> ???? > This email has been scanned for spam and viruses by Proofpoint
>> ???? > Essentials. Visit the following link to report this email as
>> spam:
>> ???? >
>> <>?
>> ???? >
>> mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5f6725180200ff49e6d753862a952d3867fbc6f5fe2e9e45705148e8e30859920fde9ceff2211e585aaf2265ab029c0d0b40090765fef6ae20dc2d4bdcd027f592db12b9b429de9de779b55cf175a013dfe33f0015ad9bc8b7ad9583f0810356fa3797bf5ce12a4a46631b36bda83b988d84421fc44e088725e2d167c92a1c677e909d7499a35e542e0d72793b2f5c9dfe84ebda61eba7d88a
>> ???? >
>>
>>
>>
>>
>>
>>
>>
>>
>> ------------------------------------------------------------------------
>>
>> This email has been scanned for spam and viruses by Proofpoint
>> Essentials. Click here <
>> report_spam.php?
>> mod_id=11&mod_option=logitem&report=1&type=easyspam&k=k1&payload=53616c7465645f5fee34ff1a185c1d35060d41d9e67985d4ae98901ed6bbeeb13416feec750e1dca4256c6e581eb51fb6e812ec19c124f543296b38ad13df1c0f78a4d3db07e5b43a18bc0d2b8dd326d45d36a4c07ad46ece63c6acd3909dab3f41b9f44dd331933fcf71c3405ee9a27e78d1b510db6acd1944de2b04b0960a785665afc0097d15e4be3048d03c8da6718c6a412ea49b255e2644e5b3fe1e5a4>
>> to report this email as spam.
>>
>>
>
>
>
>
>
>
>
> ----------
>
> This email has been scanned for spam and viruses by Proofpoint
> Essentials. Visit the following link to report this email as spam:
>
>
>
|
Chris Boone WB5ITT