开云体育

Here's my VHF beacon: N0BN>BEACON,AB0VZ-7/V: <UI>: N0BN-1/B N0BN-2/G N0BN-7/N; Bailey,CO DM79hi; Colorado R2D3/R1D6; HF-VHF Gateway:145.050 N0BN>BEACON,AB0VZ-7*/V: <UI>: N0BN-1/B N0BN-2/G N0BN-7/N;

Daniel, the BTEXT is the same for both ports, unlike most Params where they are HF/VHF there is only one BT. would be nice though. 73 Jim KI0BK

I've just set up my previously owned KAM Plus for HF and VHF operation, having disconnected my SignaLink with EasyTerm and SoundModem for HF, and PK232 for VHF. I think the KAM Plus is properly

from Kantronics manual: NODE - The term node refers to a network node such as a G8BPQ, X1-J, or NET/ROM node. Non-network nodes such as KA-Node, conference bridges, and digipeaters do not apply to

Perhaps the Addroute command is what you want. to lock a route use Addroute port neighbor call quality ! example Addroute 1 WD0EMR-7 200 ! would add or change WD0EMR-7 to your routes table with a

Very good, Jim. I respect that a node will automatically add heard broadcast nodes, but for the sake of understanding the syntax, my next question is: Your Example Addnode KSLVN:WD0EMR-7 1 WK5M-7 200

Hi Chris, The alias:node is the destination node you want to add to your nodes table, normally this happens automatically when your node hears node broadcasts. ?The only time you need to do this

Hello Group, I understand that the ADDNODE command is used to add a new destination node or to modify and existing destination node in one's node table. However, I'm hoping someone could clarify the

Hello Everyone, Am selling the below ham radio for a Silent key (AL0U) who has passed away. The rig are in excellent working condition and comes with accessories and original boxes. Kenwood TS-890,

That's awesome, Rosti! I've been so busy working on building VHF packet networks locally, I've have done much here on Network105 other than moderate.??Hope to make a connect in the future!73 de

Thank you Chris, got my HF rig setup on 14105, all looking good

Glad that this is working for you.I keep my Network 105 setup running 24/7.I will be gone for a bit this morning and then also for most of the afternoon.I do not send a beacon on Network 105.But I

K1DOW-1>MBX/1 [04/13/2025 09:30:58]: <<UI>>:{F0} just received first one, its easy when you can see waterfall. Thabk you for help Randy.

Hi Rosti,Welcome to the group. Nice meeting on Zoom last night at DEPN.More info on Network105 can found here:https://qsl.net/ww2bsa/ww2bsa-network105.htmorwww.Network105.org73 de Chris ww2bsaGroup

Thank you Randy, got all that, its just frequency i am confused about.

One more parameter to look at. After a reset and/or new from the factory the baud rate for HF packet is set at 0. This disables Packet at Port 1 of HF.I encountered this and there were no LED's even

Thank you Randy, I will give it a try. I am going to switch to my Flex6600 for now so I can see waterfall (tx/rx) and learn what i am doing, then switch back to 891. Will see what happens. I didnt

Good morning Rosti, I had the same scenario with my first KAM XL. If you are using "Data LSB" mode, make sure you have the tone pair correct. It should be a Mark tone of 1600 hz and a Space tone of

Hello, I am using KAM XL for VHF and HF, VHF setup was easy but I cant figure out that frequency I have to set my radio to for 14.105, I am using Yaesu 891, mode set to D-LSB. Audio, PTT all ok, I

Yeah, the number of Winlink stations has exploded in recent years.? Here's just a partial list of Winlink stations (if they're wideband) whose signals overlap the Net105 center-freq.? That's just