开云体育

Nick, Check in device manager when you plug it in. Some devices make multiple entries so they might be used multiple ways. If it creates a COM device (windows) then you have lots of options for how to

Manual for the Lokpilot 5 Basic is found on the same page as all the other ESU manuals, second item on: https://esu.eu/en/downloads/instruction-manuals/digital-decoders/

Ted, It's possible the LokProgrammer software is not 100% accurate. I now realize that inclusion of "Delay starting if drive sound is enabled (bit 2 of CV124)" makes no sense (but also does no harm)

I found with all the changes from Lenz to DCS210+ system I neglected to plug in the power pax. ?All good now. ?Thanks

Looks like you have 32-bit Java. But a Windows-11 machine will be 64bit... So, wrong version of Java. - Nigel

Install test shows that JAVA message says normal. Things go south when it tries to "Launching JMRI " and I suspect you might have a corrupted JMRI User data folder as you did back in 2023 were Dave

The following items have been added to the Files area of the [email protected] group. * /ProblemsBeingWorkedOn/dsand/3way LogixNG.xml (

Thanks everyone, The bar code reader does act like a keyboard, so, Bob, that clears up several of my questions and a lot of confusion. It sounds like I need to handle the input of the from the reader

Recently it became necessary to reinstall Java and JMRI. First, I checked that both programs were uninstalled. I then installed Zulu 17.56-ca-jre-17.0.14-iwin_i686.msi and JMRI5.10+Rca46bd266.exe.

A question for those having issues with the NCE Light-It. Are you all using NCE command stations or have people been seeing the same issue but use other vendor command stations? I suspect other

Folks,I discovered an interesting bug when using "Dark Mode".I have attached the system console output when attempting to change the scaling of an icon using Panel Pro v5.11.5 with dark mode

John, It might be possible to use a SignalMan in DCC mode with a LCC based command station. Or possibly in SSB mode with the RR-Cirkits LCC-LocoNet Gateway. If you are not using the lunar connections

Ken, From my POV. I don’t believe I have had any masts change state that were not addressed. The only signals that didn’t respond were directly addressed, ignoring the command when a route flipped

Ted. Some more info. I opened my LokProgrammer software and created a new LokPilot 5 Basic project. I can only assume this will give accurate information. Under 'Decoder>Driving

My bad. Found it on page 72 of the LokPilot 5 manual: "But only when the sound is switched on. You can set the start-up delay of the LokPilot 5 decoder in CV 252 in steps of 65ms." Interesting that

Ted, Definitely better asked in the LokSound group. All my locos have LokSound. None have LokPilot so I don't have direct experience. The on-line manuals for LokPilot 5 and LokPilot Basic are not

Before I changed to signman units,? the issue I had with Light-its was that they "ignored" the command.? I had nothing overly complicated in Logix.? They just seemed to ignore the commands.

If the startup delay doesn't work in your LokPilot 5 Basic, then you need to kill the delay in your LokSound 5. Try setting SoundCV13=0 (CV167=0). Mark Granville

.... and 3 virtual turnouts acting on the JMRI routes would work as well as panel buttons. -- Ken NYNH&H, Old Colony Division, Cape Cod Branch (1949-1959) Loconet * JMRI 5.11.5 * OSX,Win10,Ubuntu

Absolutely Bob JMRI routes controlling those actuators via panel selector buttons would solve the possible "conflict". -- Ken NYNH&H, Old Colony Division, Cape Cod Branch (1949-1959) Loconet * JMRI