开云体育

Dave, It depends. Reading thru the three existing? DecoderPro definition file for MTH . Early version decoder was Reset : CV55 = 55 on program track only The next decoder revision has this : In

Marc, I've worked with them since they have been around. Trust me, the instability makes setting them up, just not worth the effort if they do not get upgraded. One short circuit and they revert to

Hey Bob, Look for the Proto 3 sound labeling on the box or write up Dave In PA Sent from iPhone Xs Max

I guess it’s Foot in the mouth, since it’s a non signer of this post. Of course your CV8 comment doesn’t work. To reset a MTH decoder, you choose address 55 and then CV55 and a value of 55.

Not a problem with Digitrax, it is a problem with JMRI who does not poll and confirm the Digitrax Command Station is present or not ,for what reason I do not know. I have a Locobuffer-USB, Digitrax

I agree this is a problem with Digitrax. I tried for 5 weeks to get past the 306 error with my PR3 and could never do it despite the green indicators on the bottom of the page (and all the sage

If that system is running a JRMI version prior to 4.17.x, update date it,? There were several issues with PREFERENCES and DEFAULTS. What is nice about JMRi and NCE is that the NCE system is polled

Strangly ALL the QSI Ver 6 definitions in DecoderPro contain? Speed Table option. Even the older pre-V6 definitions contain Speed Table. As per QSI manual :

In many cases, the new Decoder Buddy is a drop in for QSI OEM decoders. Takes about 10 minutes to get the board in place. You then have a 21-pin motherboard. (I prefer Loksound, but works with any

Good evening, I have some problems with MTH / DCC decoder. JMRI Decoder Pro is never stable when detecting and reading CVs. In DCC impossible to put the CV 8 to 8 to reset the decoder. Now I have

Nick and Dave, Thank you for all the information. It has helped tremendously! I tend to prefer the SoundTraxx products so I'll take out the old decoder and update it with one of

Ray, Ignore the __MACOSX directory. The one you was is the CTC_Tutorial.jmri directory. This is a complete JMRI profile. I assume your are running Windows. C:\Users\<username>\JMRI normally

Sounds like the loss of power issue is a track issue, not a manufacture problem..... Happy with all my Proto 3 Sound Units , especially after doing their software updates Dave In PA Sent from

Bob, our club has two MTH locomotives one is an A-B-A F unit and the other a Milwaukee Road Bi-Polar. They respond to programming with Decoder-Pro but have one feature that can't be changed. In order

I understand there are work arounds to get the turnout behavior that we seek.? Plan A was use the inverted option.? That will not work because the option is grayed out.? I am sure there is a Plan B

Understand that newer MTH engines have a DCS/DCC decoder that will work fine with Decoder Pro.? I am thinking of purchasing a Dash 9 model.? How can I find out if that engine has the? DCS/DCC

After about 10 seconds that should change to red and say offline. It takes that long for the system probe to timeout. If it stays online, check if the screen says simulator or not. Also check in

Dave, You new file un-zips up as a "__MACOSX" file with no open-able files inside Ray Eiser

Dave, Allow me to expand your knowledge a little more with "non-foklore" based on experience.? Picture this, You are in the middle of an op session with 15 friends. You are using a Digitrax system

Hi, you can Google QS Industries and get their E-mail address. They are located in Beaverton, OR and ask your questions, they are glad to help. Al Babinsky Sent from Xfinity Connect Application