开云体育

John, The 4.9.2 test release will include the layout block "metric" fix along with the duplicate NX manager fix. This means that when you select the EntryExit tool in Layout Editor it will show the

This is our current trouble shooting knowledge for Sprog: SPROG Verify connection. Main menu bar should have SPROG. Click on SPROG, then "Get SPROG Firmware Version". You should see something

Dave Sand. Thank you again for your help. I followed your instructions and it worked perfectly. I am very appreciative! James Allen jcallen1@...

Ok, now that I've had a chance to look at my Mac, I'll come back to this message. Mine LI-USB-Ethernet also came up with a port of the form cu.usbmodem####, so that is the one you should use. You

Thanks Dave Sand. I'll will try that approach. Hope I can count on you if I have additional questions regarding the preference process. Again, many thanks James Allen jcallen1@...

There are some limits to what CTCParts.com can provide. CTCParts.com specializes in the "plates" one uses on a CTC machine. This is where Mike's product offerings excel. In general, Mike doesn't offer

Look at www.ctcparts.com for cast metal reproduction parts which I intend to use for my next panel. Also rixproducts has molded plastic reproduction parts. Which I have used. Mark Juett Ace Services

This is a bit off topic, but I'd like to find sources for CTC panel hardware (switches and the like), and manual locking mechanisms for local turnout control. Thanks! Jerry Michels

James, You don't need a second install. Just create a second profile. To simplify switching between them, go to "Preferences >> Config Profiles". At the bottom, select "Show Profile Selector". When

Dan B, or other members. I have two layouts with one running JMRI panel Pro for operations on my "C" drive. However, my computer also have a second hard drive (D drive) that I have been using for

Thanks, Dan. I've maintained VBA code across various versions of Excel before, so I know your pain. I'm not at the point of using JMRI and these extensions yet, but it's good to know it's a living

Rick, Yes the 240 is updated with the latest firmware. One of my roles at the club is updating firmware. All our devices; LNRP, UR92, DCS240 and the 400 series throttles are updated. I also will

Whoops, I skipped this message. Actually there are two different Excel Apps for each Manifest version, if you follow that. One is for Excel 2007 or older (back to 2000) and the other is for Excel 2020

Just to make sure, Manifest Creator and all of it's "offshoots" will run on *any* version of MS Excel/Windows beginning with Excel 2000. So you can use Excel 2000 or NEWER. Also there are currently

Just a thought. Have you updated the DCS 240? I believe there is a version 3 update available. I was have trouble programming with my DT402D. The update cured the problem.. Cheers, Rick Neibert

My attempt with that wording was to say that you needed at least Excel 2000. It will work with all of the newer versions. *Dan (Choo-Choo)** Foltz* *?* *"?A bad attitude is like a flat tire. You

First, we are running JMRI 4.8. While adding new Tam Valley Signal boards, we get no loco detected error. JMRI sees all our existing Tam Valley boards. We put back in our 200 to control the layout. We

Thanks, Gary. I'd still like to hear from Dan, in case there's some esoteric niche of non-support he's aware of. Otherwise, sounds good! Blair

Hi Blair, I'm running it on 2010. Don't know much about Excel and a friend helped me set it up and I've used Manifest Creator with it for several sessions. Gary Ray

Hi Dan, I appreciate all you have done with Manifest Creator. In the last email you said it requires MS Excel 2000. Should that be..."2000 to ???". I'm using it with MS Excel 2010. Thanks again for