开云体育

Hello, I think I know the answer, but let's see: by the end of the charge (say, 1/5th of estimated battery charge), if I'm TXing SSB or DATA, on 5 W, ALC goes to zero. If I set power to 2.5 W or less, ALC goes back to normal. When the former happens, does it mean the battery is not providing enough voltage to the radio? Daniel PY2TDB.

I've been experimenting with Winlink on my radios and had success with my little trU(SDX) but cannot Tx/Rx winlink with the FT-818. I have CAT control set up OK as the radio tries to connect with various local RMS gateways, but Winlink always reports that a Failure to connect." Ive tested a few different Baud rates without success, and have checked the Digirig settings under SoundCard and it seems to me that there needs to be an adjustment to the transmit audio to the radio from the PC where the ALC is adjusted (that was the key to success with the trU(SDX). Anyone with the above combo who have been successful and can chime in? Or anyone with a depth of knowledge about this radio and soundcard combo. Thanks! Rod VA3MZD

Hello group! I recently bought a non- ND model Yaesu Ft817 that has the Windcamp 3000mah battery installed. I can charge the battery up to 12v but, once voltage drops down to around 10v the rig shuts off. Is this normal? Any help would be greatly appreciated. 72 Mike

Hello, Does the FT-817 support CW via CAT cable? I'm trying to configure FLRIG, but without success. 73 de PY2ZA

One of my FT817nds (serial no 4H) won’t transmit on the top half of 40m. My other one is fine and this one works on the lower half and on all other frequencies. I’ve just started using this one on 40, previously it’s been 20m and above. Anyone any ideas please? A web search has only brought up “won’t transmit at all”. Any help gratefully received... Cheers, Andy M0DEL

HI I'm using my FT-817 with cat in the QLOG log (Linux version). Does anyone use it? Did you manage to configure the CW? 73 de PY2ZA jr

HI all, I am trying to repair an early model FT817. It is fine on all bands/modes in RX. It is fine on TX in all modes, except for 18Mhz (17m) and 21Mhz (15m). In the affected bands, measured in CW, the rig draws 3A+ from the bench psu, and RF filter relays buzz loudly. This can trigger a shutdown, or the rig stays on and buzzes terribly. My analysis so far - testing in CW mode: the preamp/driver stage works well. This feeds into the PA finals board, which seems to amplify happily - but supplies too much current in the affected bands. If I separate the predrivers/PA final stage from the RF filtering stage at the balun (T3001 in schematics), and insert a dummy load to absorb the PA final output, the TX works normally (~2A PSU current draw) on ALL BANDS. This suggests the issue is the balun itself or after the balun in the RF filtering stages. According to KA7OEI's fantastic info pages, https://www.ka7oei.com/ft817_rcv.html, 20m & 17m use the same RF filter FIL5, while 15m, 12m & 10m all use FIL6. Given 20m and 12m/10m work ok, this suggests the issue is not in the RF filters themselves, since they work happily 'half the time'. Through experimentation, I notice that reconnecting the balun (T3001) to the RF filter board via an inductor of ~0.3uH (originally discovered after using basic crocodile clip cables to reconnect the stages together), the TX over-current stops - and the rig operates as normal, except for the introduced inductance that rises with frequency, hence lowering the output power (and lowering the PSU current draw) with rising TX frequency. This 'fix' itself causes problems on 50+VHF/UHF I think. It suggests to me there is some low impedance path to ground around 20Mhz (affecting 18Mhz & 21Mhz), and have pulled the board out of the rig to take a look. But nothing seems immediately wrong. Has anyone experienced similar TX over-current on specific bands, where other bands work fine ? Could the issues lie in the RF filters? How best to test balun T3001 to check if it is at fault? Any ideas or suggestions are greatly appreciated, 73 de Matt Nassau, M0NJX

Hello, I'm using a generic CAT bluetooth device paired with a DIN/P2 cable connected to FT8CN for an FT8 interface. Out of whim, once or twice, if I TX at 5 W on 10 m, the ALC goes to 0. If I change the power to 2.5 W (only change I make on the rig), ALC goes to "4 bars". After a couple of TX's in this configuration if I change the power back to 5 W, ALC stays at "4 bars" permanently. Any suggestions what might be causing it? Daniel PY2TDB.

I am using my 817 again. I've had it since a year or two after they came out. Gets used in spurts but I have never used programing software such as CHIRP. Main reason is that once upon a time I read that chirp(and others) had a habit of bricking certain Yaesu radios. Was this a thing? has it been addressed? I don't mind entering things from the keyboard but starting up in a new area with a dozen or so rptrs, new HF nets, M17 etc, it would be nice to do it by cptr. And, if not chirp are there any proven apps? Thanks for any thoughts Larry

Today I was racing the bands so much during a POTA activation that I noticed I CQ'd two times 5 W in FT8 on 6 m using the wrong output (antenna was in the rear but the menu was selected FRONT). After I noticed, I corrected and the radio operated normally on both outputs (apparently). How much did I ruin the radio? Daniel.

Hello, If I use a Windcamp 3 Ah battery, I can choose the power among the values LI, LII, LIII and LIII (blinking). If I turn off the windcamp switch and plug in a 9 Ah Bioenno, I can only choose among LI, LII and LIII. Does it mean that with the Bioenno I can only output 2.5 W? Daniel PY2TDB.

I finally got the bluetooth CAT device for my 817 and am using Dan Toma’s Pocket TxRx lite after difficulty on an older Android phone. It is a very slick program. Dan gives all sorts of warnings of the potential that the program could damage the radio or radio operating system. He strongly suggests that a backup file be made, just in case the radio file gets damaged, corrupted or whatever. Does anyone know how to make a backup file for the FT817, non ND? I’ll check YouTube and Google again, to see if I can find something. Thanks

Anyone know when the new 10 w qrp rig will be available? Thanks Dave -- 73's de NU4N -- 73's de NU4N Dave

Anyone heard when the new Yaesu 10 watt radio will be available ? Thanks Dave -- 73's de NU4N -- 73's de NU4N Dave

I want to connect a receive only loop antenna and don't want to risk killing it if the 817 goes into transmit. Is there a way to inhibit the TX output. I could remove the mic so that the PTT is not available but I'd like something a bit more sure than that. Wellbrook loops are very expensive to replace!

Mike (call sign?) wrote… If you use AM for tuning, the carrier is reduced to 1.5 W or less no matter what power level you have the radio set for. It gives you a reduced power signal for tuning without having to press any buttons except the mode button. -- 73 Keith VE7GDH

This is kind of a continuation of the display thread/subject. I received the display yesterday. It came with the mini DIN cable and my 817 was able to power it. However, I am using the cat port for the LDG Z817 tuner with radio menu setting at 38400, the new display requires a cat rate of 4800. The LDG tuner has a pass through cat. Not sure how to make both work. Can I just set to the lower rate, 4800 and both will/should work? There is also a RJ45 connection option that I haven’t tried yet. Thanks all

Dears, I wish to all of you Happy Holidays and healthy year 2025! -- 73 - Petr, OK1RP http://ok1rp.blogspot.com FT-817ND | FT-818ND | FT-857D

Nice clean FT-817 (non D) FOR SALE Includes: * Ft-817. (Non D) * New Final Amplifier board with new factory installed final transistors * bhi NEDSP106 DSP super clean noise reduction * Narrow CW filter (500Hz maybe 300Hz can’t remember) * Collins Mechanical 2.3KHz SSB filter * MH-31 Microphone with up/down & fast buttons * Power Pole dc input adapter * Wire Bail stand * VHF/UHF Flexible Antenna BNC * Stubby BNC VHF/UHF Antenna * FT-817 Pack-It Reference Manual (this is the real bible) * Nifty Mini-Manual * Original Leather Case and Shoulder-Strap Checked out 80 - 10 Meter HF and 2M/440MHz this evening. The 8-step bhi DSP noise reduction really shines with todays QRN. Asking $825 insured & shipped USPS Priority Mail with tracking. Postal money order or PayPal please. John Arnold, WA6YSY Contact me off forum johna@... Will list on our favorite sale site in a couple weeks if no interest.