|
well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
tell whether they can select their preference for the thread in the
tapped hole.? mm? imperial,? & what size, that sort of thing
toggle quoted message
Show quoted text
On 11/26/20 12:17 PM, imranindiana via groups.io wrote: well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
Cliff,
after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:
made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.
nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.
one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.
i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.
imran
toggle quoted message
Show quoted text
On Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote: ?tell whether they can select their preference for the thread in the tapped hole. mm imperial, & what size, that sort of thing On 11/26/20 12:17 PM, imranindiana via groups.io wrote: well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
glad I could help
toggle quoted message
Show quoted text
On 11/26/20 9:29 PM, imranindiana via groups.io wrote: Cliff,
after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:
made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.
nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.
one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.
i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.
imran
On Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
?tell whether they can select their preference for the thread in the
tapped hole. mm imperial, & what size, that sort of thing
On 11/26/20 12:17 PM, imranindiana via groups.io wrote:
well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
toggle quoted message
Show quoted text
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote: ? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years
toggle quoted message
Show quoted text
On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
Martin on right Felder on left
 Mac,,,
Designing and building for 50 years
toggle quoted message
Show quoted text
On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
toggle quoted message
Show quoted text
On Nov 28, 2020, at 4:23 PM, Airtight: Clamps by Air Compression < airtightclamps@...> wrote:
Martin on right Felder on left
<image.jpg>
Mac,,,
Designing and building for 50 years On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years ? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran? ? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
Mac,
one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut.? it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the benefit of a T-Nut?
i have only shipped ~150 in 1.25”x0.5” with no complaints. i just carried fwd the stock established by the original big squeeze. many ways to skin a cat ?
Imran
toggle quoted message
Show quoted text
On Nov 28, 2020, at 7:23 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote: ? Martin on right Felder on left
Designing and building for 50 years On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
toggle quoted message
Show quoted text
On Nov 28, 2020, at 7:35 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mac,
one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut.? it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the benefit of a T-Nut?
i have only shipped ~150 in 1.25”x0.5” with no complaints. i just carried fwd the stock established by the original big squeeze. many ways to skin a cat ?
Imran On Nov 28, 2020, at 7:23 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote: ? Martin on right Felder on left
Designing and building for 50 years On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
Imran, I can think of a few benefits of a t-nut over non T, one would be additional pull out strength due more threads in a softer material like an aluminum or even steel if the application calls for it the other would be if you require guidance I suppose?
toggle quoted message
Show quoted text
On Nov 28, 2020, at 7:50 PM, Mark Kessler <mkessler10@...> wrote:
? Nice nuts - Mac... On Nov 28, 2020, at 7:35 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mac,
one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut.? it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the benefit of a T-Nut?
i have only shipped ~150 in 1.25”x0.5” with no complaints. i just carried fwd the stock established by the original big squeeze. many ways to skin a cat ?
Imran On Nov 28, 2020, at 7:23 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote: ? Martin on right Felder on left
Designing and building for 50 years On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
Mark,
i guess i can see benefit in softer material however, that is due to material not due to application. Felder provides T-Nuts for the secured nut for the short xcut fence. these are secured by cap screws so i take it they went with the t nut for space required to recess them. as for guidance, i have zero issues with sliding big squeeze clamps in the slot.
i wondered if they are meant to limit pinch force but i do not think they are made to a tolerance to work as such. not sure if it is even possible because of variation i have seen in slider slot lip thickness.
imran?
toggle quoted message
Show quoted text
On Nov 28, 2020, at 7:55 PM, Mark Kessler <mkessler10@...> wrote: ? Imran, I can think of a few benefits of a t-nut over non T, one would be additional pull out strength due more threads in a softer material like an aluminum or even steel if the application calls for it the other would be if you require guidance I suppose? On Nov 28, 2020, at 7:50 PM, Mark Kessler <mkessler10@...> wrote:
? Nice nuts - Mac... On Nov 28, 2020, at 7:35 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mac,
one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut.? it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the benefit of a T-Nut?
i have only shipped ~150 in 1.25”x0.5” with no complaints. i just carried fwd the stock established by the original big squeeze. many ways to skin a cat ?
Imran On Nov 28, 2020, at 7:23 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote: ? Martin on right Felder on left
Designing and building for 50 years On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
Imran,? duno, I have flat steel bar for my clamps and have no issues they are99mm x 31.76 x 12.5 (btw, they can come off the xroll with clamp attached with no modification the the handle on the xroll)  
toggle quoted message
Show quoted text
On Nov 28, 2020, at 8:06 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mark,
i guess i can see benefit in softer material however, that is due to material not due to application. Felder provides T-Nuts for the secured nut for the short xcut fence. these are secured by cap screws so i take it they went with the t nut for space required to recess them. as for guidance, i have zero issues with sliding big squeeze clamps in the slot.
i wondered if they are meant to limit pinch force but i do not think they are made to a tolerance to work as such. not sure if it is even possible because of variation i have seen in slider slot lip thickness.
imran?
On Nov 28, 2020, at 7:55 PM, Mark Kessler <mkessler10@...> wrote:
? Imran, I can think of a few benefits of a t-nut over non T, one would be additional pull out strength due more threads in a softer material like an aluminum or even steel if the application calls for it the other would be if you require guidance I suppose? On Nov 28, 2020, at 7:50 PM, Mark Kessler <mkessler10@...> wrote:
? Nice nuts - Mac... On Nov 28, 2020, at 7:35 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mac,
one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut.? it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the benefit of a T-Nut?
i have only shipped ~150 in 1.25”x0.5” with no complaints. i just carried fwd the stock established by the original big squeeze. many ways to skin a cat ?
Imran On Nov 28, 2020, at 7:23 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote: ? Martin on right Felder on left
Designing and building for 50 years On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
Mark,
interesting that your come off as it is essentially same size as mine. seems like, you may have seen the pic i sent you where i showed the slight slot i made in the slider handle. the nut you show has a generous round over, perhaps that helped. i also wonder if the handle is slightly diff. does your look like this:
i know couple of other folks may have this issue. if you do not want to shorten the nut this is an option.
imran
toggle quoted message
Show quoted text
On Nov 28, 2020, at 8:14 PM, Mark Kessler <mkessler10@...> wrote: ? Imran,? duno, I have flat steel bar for my clamps and have no issues they are99mm x 31.76 x 12.5 (btw, they can come off the xroll with clamp attached with no modification the the handle on the xroll) <image0.jpeg> <image1.jpeg> On Nov 28, 2020, at 8:06 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mark,
i guess i can see benefit in softer material however, that is due to material not due to application. Felder provides T-Nuts for the secured nut for the short xcut fence. these are secured by cap screws so i take it they went with the t nut for space required to recess them. as for guidance, i have zero issues with sliding big squeeze clamps in the slot.
i wondered if they are meant to limit pinch force but i do not think they are made to a tolerance to work as such. not sure if it is even possible because of variation i have seen in slider slot lip thickness.
imran?
On Nov 28, 2020, at 7:55 PM, Mark Kessler <mkessler10@...> wrote:
? Imran, I can think of a few benefits of a t-nut over non T, one would be additional pull out strength due more threads in a softer material like an aluminum or even steel if the application calls for it the other would be if you require guidance I suppose? On Nov 28, 2020, at 7:50 PM, Mark Kessler <mkessler10@...> wrote:
? Nice nuts - Mac... On Nov 28, 2020, at 7:35 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mac,
one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut.? it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the benefit of a T-Nut?
i have only shipped ~150 in 1.25”x0.5” with no complaints. i just carried fwd the stock established by the original big squeeze. many ways to skin a cat ?
Imran On Nov 28, 2020, at 7:23 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote: ? Martin on right Felder on left
Designing and building for 50 years On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
All of Mac's stuff looks like that.
Mac, I have a surface grinder so if you need steel made flat, I'm your guy.? Boring repetitive work is my specialty.? Dave
toggle quoted message
Show quoted text
Martin on right Felder on left
Mac,,,
Designing and building for 50 years
On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
?I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel?
10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually .
Mac,,
Designing and building for 50 years
On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
?
i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share
if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,
after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:
made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.
nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.
one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.
i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.
imran
On Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
?tell whether they can select their preference for the thread in the
tapped hole. ?mm ?imperial, ?& what size, that sort of thing
On 11/26/20 12:17 PM, imranindiana via groups.io wrote:
well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower
48.
please select reply to sender below if you are interested.
imran
|
I have been looking for t-nuts and other accessories for my Frankenstein slider. According to the small shop in Dallas that I bought the saw from, the slider portion is from an Italian manufacturer but I was never able to get the name of the company. The rest of the saw was spec'd in Taiwan. I have looked online many times trying to find a slider that looked like the one I have but haven't come up with anything yet. Below is a picture with the measurements. 
|
Imran you asked why do I shoulder my T nuts, simple answer is ,,,,I can.? My mills don’t have a none shoulder t nuts so I don’t think your saw should also .? I build a custom clamps and it is all in the details . Nice sliding t nuts that are smooth and don’t mar your slider and don’t rust are a few of the reasons.? Yes they have different specifications than the t nuts in my mills .? I make many sizes and shapes for that new, or old ?Altendorf to new or old Martins ?to Felder’s of all types to tiny little Hammers. They are T Nuts that’s why they are called that.? You are offering CR none machined taped bars. They surly fill a need and I am sure you will provide a nice product as I know how fussy you are.? Mac,,, Designing and building for 50 years
toggle quoted message
Show quoted text
On Nov 28, 2020, at 8:27 PM, David Kumm <davekumm@...> wrote:
?
All of Mac's stuff looks like that.
Mac, I have a surface grinder so if you need steel made flat, I'm your guy.? Boring repetitive work is my specialty.? Dave
Martin on right Felder on left
Designing and building for 50 years
On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
?I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel?
10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually .
Mac,,
Designing and building for 50 years
On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
?
i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share
if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,
after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:
made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.
nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.
one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.
i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.
imran
On Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
?tell whether they can select their preference for the thread in the
tapped hole. ?mm ?imperial, ?& what size, that sort of thing
On 11/26/20 12:17 PM, imranindiana via groups.io wrote:
well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower
48.
please select reply to sender below if you are interested.
imran
|
Dave I have Coval surface grinder with a new Suburban 6x18 mag chuck.? Designing and building for 50 years
toggle quoted message
Show quoted text
On Nov 29, 2020, at 8:59 AM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? Imran you asked why do I shoulder my T nuts, simple answer is ,,,,I can.? My mills don’t have a none shoulder t nuts so I don’t think your saw should also .? I build a custom clamps and it is all in the details . Nice sliding t nuts that are smooth and don’t mar your slider and don’t rust are a few of the reasons.? Yes they have different specifications than the t nuts in my mills .? I make many sizes and shapes for that new, or old ?Altendorf to new or old Martins ?to Felder’s of all types to tiny little Hammers. They are T Nuts that’s why they are called that.? You are offering CR none machined taped bars. They surly fill a need and I am sure you will provide a nice product as I know how fussy you are.? Mac,,, Designing and building for 50 years On Nov 28, 2020, at 8:27 PM, David Kumm <davekumm@...> wrote:
?
All of Mac's stuff looks like that.
Mac, I have a surface grinder so if you need steel made flat, I'm your guy.? Boring repetitive work is my specialty.? Dave
Martin on right Felder on left
Designing and building for 50 years
On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
?I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel?
10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually .
Mac,,
Designing and building for 50 years
On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
?
i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share
if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,
after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:
made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.
nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.
one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.
i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.
imran
On Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
?tell whether they can select their preference for the thread in the
tapped hole. ?mm ?imperial, ?& what size, that sort of thing
On 11/26/20 12:17 PM, imranindiana via groups.io wrote:
well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower
48.
please select reply to sender below if you are interested.
imran
|
Suburban makes good stuff.? What steel do you use for your nuts?? dave
toggle quoted message
Show quoted text
Dave I have Coval surface grinder with a new Suburban 6x18 mag chuck.?
Designing and building for 50 years
On Nov 29, 2020, at 8:59 AM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
?Imran you asked why do I shoulder my T nuts, simple answer is ,,,,I can.?
My mills don’t have a none shoulder t nuts so I don’t think your saw should also .?
I build a custom clamps and it is all in the details . Nice sliding t nuts that are smooth and don’t mar your slider and don’t rust are a few of the reasons.?
Yes they have different specifications than the t nuts in my mills .?
I make many sizes and shapes for that new, or old ?Altendorf to new or old Martins ?to Felder’s of all types to tiny little Hammers.
They are T Nuts that’s why they are called that.?
You are offering CR none machined taped bars. They surly fill a need and I am sure you will provide a nice product as I know how fussy you are.?
Mac,,,
Designing and building for 50 years
On Nov 28, 2020, at 8:27 PM, David Kumm <davekumm@...> wrote:
?
All of Mac's stuff looks like that.
Mac, I have a surface grinder so if you need steel made flat, I'm your guy.? Boring repetitive work is my specialty.? Dave
Martin on right Felder on left
Designing and building for 50 years
On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
?I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel?
10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually .
Mac,,
Designing and building for 50 years
On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
?
i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share
if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,
after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:
made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.
nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.
one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.
i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.
imran
On Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
?tell whether they can select their preference for the thread in the
tapped hole. ?mm ?imperial, ?& what size, that sort of thing
On 11/26/20 12:17 PM, imranindiana via groups.io wrote:
well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower
48.
please select reply to sender below if you are interested.
imran
|
Mac,
milled product is surely beautiful but i honestly wanted to know the benefit of a true t-nut. there is reasonable amount of time involved in a milled nut so it is justifiably expensive.
what i am offering is basic and from my experience they do the job. unfortunately there is nothing special about these nuts, so my attention to detail may not be duper useful, LOL.
i consider it a service to members as there is no money making in this. i will drive 40 mins one way to my friend to cut them on his band saw. then i drill them progressively on DP to the tap size and finally tap them by hand. $15/nut does not come close to what my time alone is worth not to mention tool wear. i am slowly trying to get into metal work and oddly enough a dozen of these is just enough to make it enjoyable.
imran
toggle quoted message
Show quoted text
On Nov 29, 2020, at 9:59 AM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote: ? Imran you asked why do I shoulder my T nuts, simple answer is ,,,,I can.? My mills don’t have a none shoulder t nuts so I don’t think your saw should also .? I build a custom clamps and it is all in the details . Nice sliding t nuts that are smooth and don’t mar your slider and don’t rust are a few of the reasons.? Yes they have different specifications than the t nuts in my mills .? I make many sizes and shapes for that new, or old ?Altendorf to new or old Martins ?to Felder’s of all types to tiny little Hammers. They are T Nuts that’s why they are called that.? You are offering CR none machined taped bars. They surly fill a need and I am sure you will provide a nice product as I know how fussy you are.? Mac,,, Designing and building for 50 years On Nov 28, 2020, at 8:27 PM, David Kumm <davekumm@...> wrote:
?
All of Mac's stuff looks like that.
Mac, I have a surface grinder so if you need steel made flat, I'm your guy.? Boring repetitive work is my specialty.? Dave
Martin on right Felder on left
Designing and building for 50 years
On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
?I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel?
10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually .
Mac,,
Designing and building for 50 years
On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
?
i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share
if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4” long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,
after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:
made out of CR1018 0.5” x 1.25” flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.
nut length is 2” but you can specify any length at $1/in for nuts over 2” in length. if shipping is affected i will let you know.
one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16” and associated coarse thread.
i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.
imran
On Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
?tell whether they can select their preference for the thread in the
tapped hole. ?mm ?imperial, ?& what size, that sort of thing
On 11/26/20 12:17 PM, imranindiana via groups.io wrote:
well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower
48.
please select reply to sender below if you are interested.
imran
|
imran
Mark Foster
Larry