Imran, I can think of a few benefits of a t-nut over non T, one would be additional pull out strength due more threads in a softer material like an aluminum or even steel if the application calls for it the other would be if you require guidance I suppose?
toggle quoted message
Show quoted text
On Nov 28, 2020, at 7:50 PM, Mark Kessler <mkessler10@...> wrote:
?
Nice nuts - Mac...
On Nov 28, 2020, at 7:35 PM, imranindiana via groups.io <imranindiana@...> wrote:
?
Mac,
one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut.?
it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the benefit of a T-Nut?
i have only shipped ~150 in 1.25¡±x0.5¡± with no complaints. i just carried fwd the stock established by the original big squeeze. many ways to skin a cat ?
Imran
On Nov 28, 2020, at 7:23 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote:
?
Martin on right Felder on left
Designing and building for 50 years
On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
?
I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel?
10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually .
Mac,,
Designing and building for 50 years
On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
?
i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4¡± long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
?
Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5¡± x 1.25¡± flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2¡± but you can specify any length at $1/in for nuts over 2¡± in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16¡± and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
