开云体育

Dave I have Coval surface grinder with a new Suburban 6x18 mag chuck. martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330 cell airtightclamps@...

Imran you asked why do I shoulder my T nuts, simple answer is ,,,,I can. My mills don’t have a none shoulder t nuts so I don’t think your saw should also . I build a custom clamps and it is all in

I have been looking for t-nuts and other accessories for my Frankenstein slider. According to the small shop in Dallas that I bought the saw from, the slider portion is from an Italian manufacturer

Colin, Unfortunately all the Jarra drums are gone I have one I made for my wife , here is picture of this one. Made of redwood . Joinery is tapered / beveled t+g this is a small drum 18” 6” to

There are several copies of the Design Manual for Cabinet Furniture available through abebooks.com, but expensive at $20-$40 since the book is only 49 pages. Gil Fuqua Nashville

Hi Mac, Have you got any pictures of the drums ?. Colin Sent from Mail for Windows 10 -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

All of Mac's stuff looks like that. Mac, I have a surface grinder so if you need steel made flat, I'm your guy. Boring repetitive work is my specialty. Dave ________________________________ Sent:

Eric, never thought of running material thru WBS to remove dust. should only take a light pass. i like tersa on mine for quick change. i am sure those pesky little hard to rotate guys do shine in

Imran, I am in your camp - joint near, plane far on my Dual 51 -- 368 of those suckers - errr, cutters - so replacing them is not only a bit of $ it is also time. As others have mentioned, what you

Mark, interesting that your come off as it is essentially same size as mine. seems like, you may have seen the pic i sent you where i showed the slight slot i made in the slider handle. the nut you

Imran, duno, I have flat steel bar for my clamps and have no issues they are99mm x 31.76 x 12.5 (btw, they can come off the xroll with clamp attached with no modification the the handle on the xroll)

Mark, i guess i can see benefit in softer material however, that is due to material not due to application. Felder provides T-Nuts for the secured nut for the short xcut fence. these are secured by

Imran, I can think of a few benefits of a t-nut over non T, one would be additional pull out strength due more threads in a softer material like an aluminum or even steel if the application calls for

Nice nuts - Mac... Regards, Mark https://www.instagram.com/kessler_woodworks/

Mac, one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut. it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the

Beautiful Mark Foster

Martin on right Felder on left Mac,,, martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330 cell airtightclamps@... airtightclamps.com

I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel 10 mm x 1.5 thread ,, beveled on 22 edges than

i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on

Murray, For hobbyists like us it is always better to ask the experts, but honestly, you are almost over thinking this. Joint it, resaw if required, plane it, buy a straight forward T&G cutter set, try