Re: A3-31 setup and calibration
Brian I was trained to set the height of the cutter head 8/10 of mm below the table edge side to side within max .06 mm then set the knives cutting circle .03 mm above table edge. Mac,, Designing and building for 50 years
toggle quoted message
Show quoted text
On May 20, 2023, at 9:01 AM, Richard <rirving@...> wrote:
?.031¡± above the body of the cutterhead, the range called for in the setup guide is .026¡± - .038¡±, and getting it precise to a mark is difficult because of how everything adjusts - two bolts front side, two m6 studs on the hinge side.?
I am wondering if I did mess up level of the outfeed and didn¡¯t realize it when making my adjustments. Will check this am.?
|
Re: A3-31 setup and calibration
.031¡± above the body of the cutterhead, the range called for in the setup guide is .026¡± - .038¡±, and getting it precise to a mark is difficult because of how everything adjusts - two bolts front side, two m6 studs on the hinge side.?
I am wondering if I did mess up level of the outfeed and didn¡¯t realize it when making my adjustments. Will check this am.?
|
Re: A3-31 setup and calibration
Wouldn¡¯t it be too low in this case if I have to set the tables to near the lower end of their travel to achieve proper distance between cutterhead and tables??
Certainly possible, though I¡¯m hoping there¡¯s a geometry issue with the tables that I¡¯ve overlooked since those adjustments are much easier. :-)?
|
Re: A3-31 setup and calibration
.031" above the body of the cutterhead, or the height of the blades? How. Did you adjust the outfeed table? If you didn¡¯t keep it level as you adjusted it, then tipping the plane of the table could easily put you out of range on the adjustment of the infeed table.
Brian Lamb
blamb11@...
www.lambtoolworks.com
toggle quoted message
Show quoted text
On May 19, 2023, at 9:12 PM, Richard <rirving@...> wrote:
So I¡¯ve gotten the outfeed leveled and set .031¡± above the cutterhead. The problem when I do that is the infeed loses the majority of its travel and now has a height adjustment of only 0 - .09¡±. Beyond that the height adjustment bottoms out at the end of its travel. I¡¯m sure there¡¯s something I screwed up adjusting the outfeed but I haven¡¯t figured it out yet.?
|
Re: A3-31 setup and calibration
I¡¯m talking whole cutter head not table to head Designing and building for 50 years
toggle quoted message
Show quoted text
On May 20, 2023, at 8:12 AM, mac campshure <mac512002@...> wrote:
? Maybe the cutterhead assembly is too high??? Mac,, Designing and building for 50 years On May 19, 2023, at 11:12 PM, Richard <rirving@...> wrote:
?So I¡¯ve gotten the outfeed leveled and set .031¡± above the cutterhead. The problem when I do that is the infeed loses the majority of its travel and now has a height adjustment of only 0 - .09¡±. Beyond that the height adjustment bottoms out at the end of its travel. I¡¯m sure there¡¯s something I screwed up adjusting the outfeed but I haven¡¯t figured it out yet.?
|
Re: A3-31 setup and calibration
Maybe the cutterhead assembly is too high??? Mac,, Designing and building for 50 years
toggle quoted message
Show quoted text
On May 19, 2023, at 11:12 PM, Richard <rirving@...> wrote:
?So I¡¯ve gotten the outfeed leveled and set .031¡± above the cutterhead. The problem when I do that is the infeed loses the majority of its travel and now has a height adjustment of only 0 - .09¡±. Beyond that the height adjustment bottoms out at the end of its travel. I¡¯m sure there¡¯s something I screwed up adjusting the outfeed but I haven¡¯t figured it out yet.?
|
Re: Electronic brake C3 31
Hi Nathan,
I sent you a private msg.
toggle quoted message
Show quoted text
On May 20, 2023, at 2:13 AM, Nathan D'Elboux <nathan.delboux@...> wrote: ?Hi all, I used to own a 2012 model hammer c31 combo unit and I remember the electric motor of the table saw used to applying an electronic break buzzing sound to slow the blade to a complete stop, as my n4400 bandsaw currently has as well. ?I no longer own that 2012 model, my current model is a 2016 and everything else is the same but the table saw doesn¡¯t apply an electric brake when I turn it off. The helical head and router spindle does but the tablesaw slows down eventually there¡¯s no buzzing sound
do others find the same? Is it supposed to have one consistently across the range of products and I should be raising it as a fault with Felder directly or it¡¯s not common across all hammer motors?
I just thought it would have one given an older saw used to but this is not the case
thanks for any advice
Nathan?
|
Re: Electronic brake C3 31
Nathan - My 2018 C3-31 also has the buzzing sound when the saw blade stops.
toggle quoted message
Show quoted text
On May 20, 2023, at 6:11 AM, Rich M. <rmarkiewicz@...> wrote:
?Hi Nathan - My 2018-build C3-31 has the buzzing sound on the table saw blade as well.????? -Rich M.
|
Re: Electronic brake C3 31
Hi Nathan - My 2018-build C3-31 has the buzzing sound on the table saw blade as well.????? -Rich M.
|
Hi all, I used to own a 2012 model hammer c31 combo unit and I remember the electric motor of the table saw used to applying an electronic break buzzing sound to slow the blade to a complete stop, as my n4400 bandsaw currently has as well. ?I no longer own that 2012 model, my current model is a 2016 and everything else is the same but the table saw doesn¡¯t apply an electric brake when I turn it off. The helical head and router spindle does but the tablesaw slows down eventually there¡¯s no buzzing sound
do others find the same? Is it supposed to have one consistently across the range of products and I should be raising it as a fault with Felder directly or it¡¯s not common across all hammer motors?
I just thought it would have one given an older saw used to but this is not the case
thanks for any advice
Nathan?
|
Re: A3-31 setup and calibration
So I¡¯ve gotten the outfeed leveled and set .031¡± above the cutterhead. The problem when I do that is the infeed loses the majority of its travel and now has a height adjustment of only 0 - .09¡±. Beyond that the height adjustment bottoms out at the end of its travel. I¡¯m sure there¡¯s something I screwed up adjusting the outfeed but I haven¡¯t figured it out yet.?
|
Re: Felder Silent Power Dado 6.3-20mm
#forsale
Btw, if successful in identifying and procuring said adjustable groover for circular saws, a Forrest dado stack will be available¡. 8¡±
toggle quoted message
Show quoted text
On May 19, 2023, at 7:56 PM, habacomike via groups.io <habacomike@...> wrote:
Primarily for cutting grooves (dados) in solid stock for furniture work. ?My spouse is looking for an anniversary present for me. ?The Forrest stack is ok, but the adjustability of the width of the groove is a pain in the ass. ?I have adjustable groovers for the shaper on CF741. ?I want to be able to set my dado up like David Best! ?Budget is less that 1.2k. ?I¡¯d hoped to buy the groover that was listed above but no luck for a deal¡
Mike On May 19, 2023, at 7:41 PM, David P. Best <dbestworkshop@...> wrote:
Mike, Can you comment a bit on your budget for the groover and your intended ?application? ?That would help narrow the alternatives. David Best
DBestWorkshop@...
https://www.flickr.com/photos/davidpbest/collections/
https://www.youtube.com/@David_Best
On May 19, 2023, at 6:37 PM, habacomike via groups.io <habacomike@...> wrote:
Thanks everyone. ?I have a Forrest dado stack; what I want is an adjustable groover for the saw. ?Any options other than Felder?
|
Re: Felder Silent Power Dado 6.3-20mm
#forsale
Primarily for cutting grooves (dados) in solid stock for furniture work. ?My spouse is looking for an anniversary present for me. ?The Forrest stack is ok, but the adjustability of the width of the groove is a pain in the ass. ?I have adjustable groovers for the shaper on CF741. ?I want to be able to set my dado up like David Best! ?Budget is less that 1.2k. ?I¡¯d hoped to buy the groover that was listed above but no luck for a deal¡
toggle quoted message
Show quoted text
On May 19, 2023, at 7:41 PM, David P. Best <dbestworkshop@...> wrote:
Mike, Can you comment a bit on your budget for the groover and your intended ?application? ?That would help narrow the alternatives.
David Best
DBestWorkshop@...
https://www.flickr.com/photos/davidpbest/collections/
https://www.youtube.com/@David_Best
On May 19, 2023, at 6:37 PM, habacomike via groups.io <habacomike@...> wrote:
Thanks everyone. ?I have a Forrest dado stack; what I want is an adjustable groover for the saw. ?Any options other than Felder?
|
Re: Felder Silent Power Dado 6.3-20mm
#forsale
Mike, Can you comment a bit on your budget for the groover and your intended ?application? ?That would help narrow the alternatives.
David Best
DBestWorkshop@...
https://www.flickr.com/photos/davidpbest/collections/
https://www.youtube.com/@David_Best
toggle quoted message
Show quoted text
On May 19, 2023, at 6:37 PM, habacomike via groups.io <habacomike@...> wrote:
Thanks everyone. ?I have a Forrest dado stack; what I want is an adjustable groover for the saw. ?Any options other than Felder?
|
Re: Felder Silent Power Dado 6.3-20mm
#forsale
Thanks everyone. ?I have a Forrest dado stack; what I want is an adjustable groover for the saw. ?Any options other than Felder?
toggle quoted message
Show quoted text
On May 19, 2023, at 5:04 PM, imranindiana <imranindiana@...> wrote:
I have a CMT dado stack purchased from Scott&Sargent. After I bought it a felder dado set came up for sale, which I bought. Anyhow, I have it for sale on FB.
| |
imran
Nathan D'Elboux
David P. Best
Dan Gavrilyuk