Re: 95 EVC - Rear bench storage accessibility
David, at 1705.net wrote up his platform bed conversion, which includes better under-seat access. Check it out:
https://1705.net/platform-bed-details/
By
Joshua Van Tol
·
#163627
·
|
95 EVC - Rear bench storage accessibility
Hi group,
I'm looking to see if anyone has figured out how to make the rear bench storage (underneath) easier to access.
Ideally it would be nice to easily open this without it shifting to go into
By
druuid@...
·
#163626
·
|
Re: relacing an arm rest, in '02 Weekender
got it, thanks!!
By
Ricki-Ellen
·
#163625
·
|
Re: relacing an arm rest, in '02 Weekender
6mm Allen key or long bit.
--
Justin
2000 EVW 1.9TDI Syncro 5-spd
490k mi :-)
By
Justin Soares
·
#163624
·
|
relacing an arm rest, in '02 Weekender
Can someone tell me what tool(s) I need to replace an arm rest in my '02 Weekender? ?I took out the rear-facing seat (long ago, not needed), and am hoping I can remove an arm rest from that seat and
By
Ricki-Ellen
·
#163623
·
|
Re: AXK Engine rebuild in PNW
EURO PRO in Spokane is highly recommended by my local mechanic.? I trust his judgment.? I may need an engine rebuild soon.
Jim Loomis2002 EVC
By
James Loomis
·
#163622
·
|
2001 Eurovan MV
Getting ready to put our MV on the market.? Sad, but realistically, it's not getting used.? Bought from a friend 7/2020 w/95k and currently only has
By
Antonio Martinez <middleriverstudio@...>
·
#163621
·
|
Re: AXK Engine rebuild in PNW
Mike
i don’t have any suggestions on shop, but I believe GTA only does Trans- I shipped my trans to them (from N. Carolina) for a go over and a $2 seal replacement at about 227 kmi (it had no issues
By
Phil <apothecarymortar@...>
·
#163620
·
|
Re: AXK Engine rebuild in PNW
They’re exclusively a tranny shop last time I checked. It’s been awhile though…
--
Justin
2000 EVW 1.9TDI Syncro 5-spd
490k mi :-)
By
Justin Soares
·
#163619
·
|
Re: AXK Engine rebuild in PNW
By
Vance Stasna
·
#163618
·
|
Re: AXK Engine rebuild in PNW
German Trans axle in Bend Oregon. They only work on vehicles shipped or brought to their shop.
By
Peter Bedegi
·
#163617
·
|
AXK Engine rebuild in PNW
Well it seems to finally be time to freshen up the motor in our 2002 EV MV Weekender. It has about 260,000 miles on it. I was going to take it on a long road trip to CO last week but just prior, the
By
MasterMarine
·
#163616
·
|
Re: LP tank repair or replace on Eurovan?
I replaced my shut off valve (rather, had it done by a local propane outlet). While I was doing that, I replaced the regulator and painted the tank, as well. You can read about it here:
By
David
·
#163615
·
|
Re: LP tank repair or replace on Eurovan?
Hi Mark,? Hopefully you're still following eurovanUpdate...? I'm experiencing the same LP tank service valve malfunction, live in Charlestown, and am unable to find anybody to help repair.? Have
By
phatswag@...
·
#163614
·
|
Re: Looking for front door panel "wedges" 95 EVC
Thanks for the reply Joshua!? I've seen the listings but I'm leery that they aren't actually the part and how difficult the return would be.? I was hoping that someone had a success story and a
By
TDIbiker
·
#163613
·
|
Re: 1993 EV - heater core failure (I think) in SoCal
All you are doing is connecting one hose to another.? The clamps are already there and for 2001 to 2003 I know that a union is already in place right there by the little screw vent.? You can
By
Steve
·
#163612
·
Edited
|
Re: Looking for front door panel "wedges" 95 EVC
Googling that part number shows several online dealers who purport to have the part new. There's a chance you'll order it and they'll cancel the order because stock doesn't really exist, but it's
By
Joshua Van Tol
·
#163611
·
|
Looking for front door panel "wedges" 95 EVC
Does anyone know of a source for the two plastic "wedges" that create the transition from the door frame to the door panel and close the gap with the seal? There is one at the top of the front and
By
TDIbiker
·
#163610
·
|
Re: 1993 EV - heater core failure (I think) in SoCal
Hello,
I am having the exact issue on my 2003 Weekender.? Would you please kindly let me know where you purchase the bypass kit?? Also, have you had a chance to post the photos yet?? Thank you!
By
leovfelipe
·
#163609
·
|
Pressure rating for 2002 EVC Rack & Pinion
As posted earlier, I need a rack and pinion assembly for 2002 EuroVan Camper.There seems to be several different pressure ratings on different units.Does anyone know what the pressure rating would be
By
Malcolm Stebbins <mwstebbins@...>
·
#163608
·
|