开云体育

My go to solution for EX gateways is Cresnet power (just 24V and GND) and
ethernet comms. They are picky about PoE but I prefer their response and
manageablity over ethernet.


On Tue, May 14, 2013 at 9:10 AM, Thomas <tluczywo@...> wrote:

**


I've done projects with gateways operating via Cresnet (8 remotes, 6
remotes), no issues.

Tom L.


--- In Crestron@..., Nick Mitchell <nick@...> wrote:

Kevin,

Don't switch them to cresnet. We saw lots of performance issues with
gateways and cresnet. Invest in a UPS so it doesn't loose power lol.

Nick



Sent from my eMail.

On May 14, 2013, at 9:18 AM, Kevin Keenan <kevinfkeenan@...> wrote:



I have a project with 7 MLX-3 s and three gateways connected to a CP3

via a

Pakedge POE switch. Every time the customer loses power, the gateways

lock

up. (They usually blame the remotes, but pulling the batteries or

rebooting

the MLX-3 does not help) We have to cycle the power on the gateways and
wait about 10 minutes, then all is fine.

I am thinking about rewiring the gateways to use Cresnet instead of
Ethernet.

-Kevin

On May 13, 2013, at 18:51, "chrish172003" <chris@...> wrote:

just out of interest has anyone experienced any lockups with the mlx-3

on

the mc3?

panel comes unresponsive and then you have to reboot the gway to or

pull

the batteries on the panel to get it to work again

------------------------------------



Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links

I found that setting when I was having a look around earlier, it was set to enabled. The panel was working perfectly up until the end of last week then developed this problem.

--- In Crestron@..., "Chip" <cfm@> wrote:

For reasons I can't fathom, this panel (I'm sure it must be on others as well) has a "Cresnet On/Off" setting in the setup pages...

:(

- Chip


--- In Crestron@..., "roray32" <roray.stewart@> wrote:

Hi,

I have TPMC-12 which appears to have developed a problem with its Cresnet connection. In toolbox I can see the panel on IP, looking at the AV2 it's connected to it lists no Cresnet devices attached. I have re-uploading the code and have also re-uploaded the firmware to the panel but this has made no difference. I can see the code on the panel but when operating it just carries out page flips, doesn't control the system in any way.

Panel is running firmware: 1.00.02.90

Any ideas as to what else I can check or try before I send it back for repair.

Thanks
Roray

It works okay with iDoc, haven't used it with Audionet, and I've had bad luck with it on TRACK AM/FM/XM.

One thing I've found on a couple of systems now is that when using it with the iDoc, it screws up the menus for the "old" style logic. The first two pages of menus in the tree come out blank the second time you try to access them.

Heath


On May 13, 2013, at 6:21 AM, Phil Bridges <gravityhammer@...> wrote:

Have any of y'all used this in a production environment?

I'm looking for opinions on its use, particularly with an iDoc and Audionet.

I used the Media Player object for the first time last month, with several TSW
panels, a couple of DGE-2's, and an X-Panel. We used it with an IDOC and
CEN-TRACK (AM, FM, XM, and AUDIONET).

Some of the features were nice, but I REALLY disliked not being able to change
(easily) simple things like object & font sizes, placement, and even button
labels.

It was also VERY SLOW to startup. I don't know if that was because we were
using multiple sources, or if that's just how it is, but it was noticeable and
annoying. Overall I wasn't impressed, and will continue to use "the old way"
for those sources unless someone specifically requests the Media Player, or it
gets a lot better.

--- On Monday, May 13, 2013 at 8:21 AM, Phil Bridges wrote:

Have any of y'all used this in a production environment?

I'm looking for opinions on its use, particularly with an iDoc and
Audionet.

I was offered a 3 month extension way back when I did mine. I called Laura the last day before it was due to see if I could submit in the following Monday. I'd stayed up all night for 2 days in a row and was so close but had some other commitments that got in the way.

I turned down the 3 month extension in favour of a 3 day one. If I'd taken the 3 months I never would have gotten motivated to finish.

Sent from my iPhone

On 2013-05-14, at 10:49 AM, "jbudz1977" <jbudz1977@...> wrote:

Meh, they essentially gave us 6 months to complete the exam, which was plenty of procrastination time. If it was open ended I may have never had the motivation to actually get it done...

It did suck having to take Programming for Certification a second time, but.. I had a different instructor and learned different things, and I always love a "Crestron Vacation."

--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:

What!!?? Good grief they are killing me. That isn't fair to all the other certified people.....wow. That is all I have to say on this one.

I was offered a 3 month extension way back when I did mine. I called Laura the last day before it was due to see if I could submit in the following Monday. I'd stayed up all night for 2 days in a row and was so close but had some other commitments that got in the way.

I turned down the 3 month extension in favour of a 3 day one. If I'd taken the 3 months I never would have gotten motivated to finish.

Sent from my iPhone

On 2013-05-14, at 10:49 AM, "jbudz1977" <jbudz1977@...> wrote:

Meh, they essentially gave us 6 months to complete the exam, which was plenty of procrastination time. If it was open ended I may have never had the motivation to actually get it done...

It did suck having to take Programming for Certification a second time, but.. I had a different instructor and learned different things, and I always love a "Crestron Vacation."

--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:

What!!?? Good grief they are killing me. That isn't fair to all the other certified people.....wow. That is all I have to say on this one.

What!!?? Good grief they are killing me. That isn't fair to all the other certified people.....wow. That is all I have to say on this one.

My go to solution for EX gateways is Cresnet power (just 24V and GND) and
ethernet comms. They are picky about PoE but I prefer their response and
manageablity over ethernet.


On Tue, May 14, 2013 at 9:10 AM, Thomas <tluczywo@...> wrote:

**


I've done projects with gateways operating via Cresnet (8 remotes, 6
remotes), no issues.

Tom L.


--- In Crestron@..., Nick Mitchell <nick@...> wrote:

Kevin,

Don't switch them to cresnet. We saw lots of performance issues with
gateways and cresnet. Invest in a UPS so it doesn't loose power lol.

Nick



Sent from my eMail.

On May 14, 2013, at 9:18 AM, Kevin Keenan <kevinfkeenan@...> wrote:



I have a project with 7 MLX-3 s and three gateways connected to a CP3

via a

Pakedge POE switch. Every time the customer loses power, the gateways

lock

up. (They usually blame the remotes, but pulling the batteries or

rebooting

the MLX-3 does not help) We have to cycle the power on the gateways and
wait about 10 minutes, then all is fine.

I am thinking about rewiring the gateways to use Cresnet instead of
Ethernet.

-Kevin

On May 13, 2013, at 18:51, "chrish172003" <chris@...> wrote:

just out of interest has anyone experienced any lockups with the mlx-3

on

the mc3?

panel comes unresponsive and then you have to reboot the gway to or

pull

the batteries on the panel to get it to work again

[Non-text portions of this message have been removed]




[Non-text portions of this message have been removed]

[Non-text portions of this message have been removed]



------------------------------------



Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links

I just took the advanced class the first of March and I also due to my work load haven't been able to spend enough time that I would be able to finish by my deadline. So I emailed Crestron to get an extension and found out that they have dropped the 3 month deadline. I'm not sure how far back that will count for but I was relieved to hear I had more time to finish mine.

Nate L.

Sent from my iPad

On May 14, 2013, at 10:50 AM, "cyberbri24" <cyberbri24@...> wrote:

I guess it's my time to chime in lol...

Been programming for 12 years. Starting out in resi and stayed there for most of that time. Largest system was 22 TP, 20 zones of A/V, 250K theater within, full smart home (HVAC, SHADES, JANDY, CCTV, you name it they had it), and 6 full racks of gear totaling about $1 mil. This was all done only having Essentials experience. From there and attending Intermediate class, everything was easier because most systems was 1-6 rooms. After the market crash I moved over to Commerical because companies have annual budgets to spend and I got in with a few A/V commerical companies always needing programming. I finally took my Cert class very recently but my current workload (which is a good thing)has kept me from finishing my exam. I will finish it at some point, just not sure if they make me attend another class before that happens? Has anyone gone past the 3 months date?
I have been an admin of a few large RVSE systems. From 150 to 250 rooms, I have yet to really use all the features such as room messaging or scheduling as the client always had other SW for making the rooms available so I never needed to worry about it. The clients mostly look for managing and keep track of scheduling the events to shutdown rooms for better bulb life, knowing the lamp hours for PM care and helping assist a user by using the x-panel feature. The rooms need occupency sensors and IP cameras to help aid in knowing if a room is really in use or not or just left on IMO.

Question I have, is there going to be a qwerty keyboard released yet for Core 3UI anytime soon?

Thanks,
cyberbri

--- In Crestron@..., "jbudz1977" <jbudz1977@> wrote:

RV Express has a Help Message and Help Response Text Field...


--- In Crestron@..., Lincoln King-Cliby <lincoln@> wrote:

Yeah, but I don't think RV Express (RV6) supports the messaging, etc. of RV7 / RV SE... I could be wrong since it's been more than a few years since I've seen anyone do RV SE so maybe that capability has been added [or has been there all along and, as I said, I just have never had a need for it]

Lincoln

For reasons I can't fathom, this panel (I'm sure it must be on others as well) has a "Cresnet On/Off" setting in the setup pages...

:(

- Chip


--- In Crestron@..., "roray32" <roray.stewart@> wrote:

Hi,

I have TPMC-12 which appears to have developed a problem with its Cresnet connection. In toolbox I can see the panel on IP, looking at the AV2 it's connected to it lists no Cresnet devices attached. I have re-uploading the code and have also re-uploaded the firmware to the panel but this has made no difference. I can see the code on the panel but when operating it just carries out page flips, doesn't control the system in any way.

Panel is running firmware: 1.00.02.90

Any ideas as to what else I can check or try before I send it back for repair.

Thanks
Roray

Well that can't be your problem. What other simpl+ stuff do yo have going on?

--- In Crestron@..., "coolaiddrinker" <coolaiddrinker@> wrote:

i have biamp modules in the program only 3 dialer, mic mute and vol control v5.2

--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:

What is your dsp in this system? On the av2 I had issues with, the program was using BSS audio modules. The newest modules off of the BSS site would lock that av2 everytime. Reverted to some older modules and no more problems. I could load that same program that would lock the av2 and it would run fine on MPC-M10. I still would like to know why the av2 would lock though. The program was really small too: 80 symbols, 314 digital, 24 analog, 25 serial, so I know it wasn't out of memory.

Hi,

I have TPMC-12 which appears to have developed a problem with its Cresnet connection. In toolbox I can see the panel on IP, looking at the AV2 it's connected to it lists no Cresnet devices attached. I have re-uploading the code and have also re-uploaded the firmware to the panel but this has made no difference. I can see the code on the panel but when operating it just carries out page flips, doesn't control the system in any way.

Panel is running firmware: 1.00.02.90

Any ideas as to what else I can check or try before I send it back for repair.

Thanks
Roray

**


Well that can't be your problem. What other simpl+ stuff do yo have going
on?


--- In Crestron@..., "coolaiddrinker" <coolaiddrinker@...>
wrote:

i have biamp modules in the program only 3 dialer, mic mute and vol

control v5.2

--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:

What is your dsp in this system? On the av2 I had issues with, the

program was using BSS audio modules. The newest modules off of the BSS site
would lock that av2 everytime. Reverted to some older modules and no more
problems. I could load that same program that would lock the av2 and it
would run fine on MPC-M10. I still would like to know why the av2 would
lock though. The program was really small too: 80 symbols, 314 digital, 24
analog, 25 serial, so I know it wasn't out of memory.

have you checked the wireing? sounds like there might be a loose connection somewhere.

--- In Crestron@..., "roray32" <roray.stewart@> wrote:

Hi,

I have TPMC-12 which appears to have developed a problem with its Cresnet connection. In toolbox I can see the panel on IP, looking at the AV2 it's connected to it lists no Cresnet devices attached. I have re-uploading the code and have also re-uploaded the firmware to the panel but this has made no difference. I can see the code on the panel but when operating it just carries out page flips, doesn't control the system in any way.

Panel is running firmware: 1.00.02.90

Any ideas as to what else I can check or try before I send it back for repair.

Thanks
Roray

i have biamp modules in the program only 3 dialer, mic mute and vol control v5.2

--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:

What is your dsp in this system? On the av2 I had issues with, the program was using BSS audio modules. The newest modules off of the BSS site would lock that av2 everytime. Reverted to some older modules and no more problems. I could load that same program that would lock the av2 and it would run fine on MPC-M10. I still would like to know why the av2 would lock though. The program was really small too: 80 symbols, 314 digital, 24 analog, 25 serial, so I know it wasn't out of memory.