Thanks so much, I have tried this but it will not boot, even after factory reset.? File size is a tenth of the old one at only 319kb.

Here's the image of a CP3 I took a few months ago:



I used the HDD raw copy tool.

I wish you the best of luck!

I desperately need an image of the SD card for a CP3 (and ideally CP3N) if anyone can share with me.? Will immediately change MAC address, etc. Thanks in advance if anyone can help.

My latest article, "New Amazon Service Could Disrupt the PERS Industry” is being published by the good folks at Residential Tech Today Magazine on their web site.?? To bring news and events

Amazon has released a new service, Alexa Emergency Assist, that competes directly with services offered by the personnel emergency response industry at a significantly lower cost.? This article goes into the details of this new service, which may be of interest to both seniors and anyone who lives alone.? It could also be of interest to integrators whose older customers could find added value to this service in their integrator installed smart homes.

You can find the article here:




For those interested in earlier articles that I've written, you can find those here:



I've found a new site to host my blog so for those that want to see even more content I've written about smart home technology you can find that using the link below.? The process of exporting all my old content from Blogger and importing it into WordPress was far from perfect.? So there are formatting issues with old posts and images that didn't import.? I will see what I can do about correcting some of these issues over time.



Thanks

You can send a direct macro command via TCP/IP using an SIO or Serial Send

Port 5951
IPAddress (IPaddress of Tricaster)

Command:
<shortcut name="play_macro_byname" macro_name ="Macro-1"/>\n

Where Macro-1 is the name of your macro

开云体育

开云体育

Just finished integrating these FRAMEs.
ART Mode ON works like an input.
If TV is OFF, you have to turn the set on to use ART Mode (or the other inputs of course).
We're using ART Mode for the 'Off State' and HDMI 1 for the feed from the VSW.

Seems to work well...

开云体育

I don't think an input command kicked it out of art mode, but I was implementing them in an out of state project, so my testing wasn't as thorough as I would've liked. I was able to get the behavior I was going for but I wasn't excited about the implementation. Felt a little like IR control of certain projectors with steppers sending commands multiple times and such.

The message saying it needs formatting is normal (don't do it though). That's because the data that's on it isn't formatted for Windows. Not sure why you're not seeing it in WinDisk32 though. It worked for me using the built in microSD slot on my Dell laptop.
--
Josh Winn
The LiquidPixel Group

Thanks Andrzej,

This is what we ended up doing as we were running short on time.? Thank you for taking time to reply.

Hi Igor,

?

Thank you and sorry for the late reply.? My mails from here seem to be bouncing back.? I will definitely play with this a bit more.

Regards,

I am using HDD raw copy:



AFAIK this works very well for both AMX and Crestron controller CF and SD cards.
NB: cards for Crestron controllers will have to be edited, using HxD or a similar editor, to 'adjust' the MAC address.

Bare in mind that many USB to SD card readers do not support burning images.? Even the SD card readers built into many laptops do not support burning images.? I have never used WinDisk32, but that could be why WinDisk32 doesn't work for you.? Here is a USB SD card reader that I have found that can be used to create/restore images.
https://www.canakit.com/mini-micro-sd-usb-reader.html

But really your best option is to create an image using the Linux DD command.? Just be careful as you could land up wiping your OS instead.
If you have a Raspberry Pi? laying around, you can created or restore images with it.
Or if you have an old PC laying around, you could boot it with a Linux boot USB and run DD that way.
Unfortunately, I think you are out of luck trying to use DD with "Linux on Windows with WSL" as I don't believe DD will have the proper low level interface from a window's host.

As soon as I insert the card I get the message to format it and it doesn’t show up in WinDisk32.

assumed I would need something else
in windows.

It will create the image as well.

Is there a Windows based tool to get an image from a good SD card?

I know I can create a good SD card from an image with WinDisk32 but want to create backup images of a couple of my devices.

Same problem, with the HZ-KPCN model ?

what I did was change the “Vitrual Interface” from false to true and back. After that the compile was complete.?