开云体育

Dear OMs, I work my DX10 with an EFHW on 40/20/15/10m and a 1:64 Balun. Tuning was working fine for a while and I had rapports 55 to 59 within Europe. I never saw the "High SWR" warning in the display, worked SSB only and did either have SWR or Power displayed in the meter. I also checked operation with a chain of power attenuators. SWR 1.1 or less here without tuning. After Power up I can tune on the band where it is with the normal long relais klicking and also transmit with full power. When I switch the band eg. 7MHz to 14MHz and press the tune button long there is only a short relay click and tuning ends. No error message, it's just back in rx. With a short press I can switch tuning on/off. Now in this case there is no TX power output. When I try to send the TX light is on, power setting is at 100W but the power meter is fixed at zero. After a complete system power cycle I can transmit again with full power. The Device is ~3 Month old, nothing gets hot, all is clean. AS said above I get the same with antenna and attenuator at the output. Anybody an idea? Is there a way to delete stored tuner data only? I received the info to try a factory reset, but this would also kill my audio settings I did several weeks ago. 73 DC0LA

hi, there is standard a 500hz cw filter in the second if, 8,83mhz most it be activated or can be deactivated per menu, or is it all the time present in cw mode, i have the radio only since few days carlos on6cn

The microphone cable on my FT-8800 has given up the ghost, and no longer works properly. The insulation has worn out, exposing bare copper. Does anyone have experience replacing the cable only (YAESU T9206534 (it's half the price of the entire microphone assembly)? Thank you - 73! Karl Kaucher KK4KRK

HF + VHF + UHF Transceiver, Power Supply, Manuals, and more For Sale: . Yaesu FT-847 HF+++ Transceiver: The Yaesu FT-847 changes base operation forever. Now you get three radios in one -- HF, VHF/UHF and satellite. You get 100 watt output on HF and 6 Meters, plus 50 watts on both 2 Meters and 430 MHz bands. Additional features include: Cross-band Full Duplex operation, Normal/Reverse Tracking, CTCSS/DCS Encode and Decode, 0.1 Hz tuning steps, DSP Notch, DSP NR and DSP BPF, Shuttle Jog Tuning Dial, Carry Handle and Keypad Entry. The FT-847 is also 1200/9600 bps Packet ready. 10.2 x 3.4 x 10.6 inches. Features: HF/VHF/UHF DSP Filters Dual Watch 0.1 Hz Tuning CTCSS/DCS Decode and Encoode Cross-band Full Duplex 1200/9600 Packet Ready It covers all of the normal ham bands in one package with virtually all modes! This one works 100% and looks like new. No defects. With paper work for $850. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 Technical Supplement for Yaesu FT-2700 Dual Band Mobile. Looks new. $20 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .

When switching the unit on/off the S/RF meter momentarily deflects and TX RX momentarily light up. Is this normal?

I'm hoping there are some old-timers hanging around here. I have an FT-530 I've had since 1998. I use it a lot, and have not had a total memory failure in decades, until recently. While changing the memory backup battery, something went wrong and it went to "factory reset". I have restored all the important stuff, but one thing I had was the OFF display showed the battery voltage. Now it shows the clock. I can't find anywhere in the manual or my cheatsheets how to get back to the battery voltage display. I do know how to get the secondary display to show battery voltage, and that is not what I'm looking for. I also know how to set it to have nothing display when off. Anybody know what I'm missing? KE6BJQ - Tim -- Best regards, Tim Slattery

Hi, all. Tonight I unfortunately put too many volts thru my FTM-200 and burned it up. Anyone know if this is repairable? Maybe burned and internal fuse or diode? Appears the FTM-500 has an internal fuse. Also looking for a schematic for this radio. Thanks for reading. Erick KE0SMR

HF Transceiver, HF + VHF + UHF Transceiver, Power Supply, Manuals, and more For Sale: . Yaesu FT-1000 D Deluxe HF Transceiver: - The Yaesu FT-1000 was designed for optimum performance and operability. The FT-1000 project involves a wholly new approach to the application of the latest digital and RF technologies to today's most demanding HF bands. - Six microprocessors and five Direct Digital Synthesizers. Receiver covers 100 kHz to 30 MHz. - Features: Adjustable power up to 200 watts Five Direct Digital Synthesizers QRM Rejection Systems 100 Memories Optimized Digital Communications Modes Simultaneous Dual (Unlimited) Frequency Reception Flexible Mode and IF Filter Automatic Antenna Tuner with 39 memories Special Features for CW Operation - This one appears to be the "D" model, with the BPF-1, TCXO-1, and a crystal filter instead of ceramic. - It works as it should, and looks extremely nice. Pristine. Buy it in its original box, with operating and service manuals on CD, for $1200. . Yaesu FT-847 HF+++ Transceiver: The Yaesu FT-847 changes base operation forever. Now you get three radios in one -- HF, VHF/UHF and satellite. You get 100 watt output on HF and 6 Meters, plus 50 watts on both 2 Meters and 430 MHz bands. Additional features include: Cross-band Full Duplex operation, Normal/Reverse Tracking, CTCSS/DCS Encode and Decode, 0.1 Hz tuning steps, DSP Notch, DSP NR and DSP BPF, Shuttle Jog Tuning Dial, Carry Handle and Keypad Entry. The FT-847 is also 1200/9600 bps Packet ready. 10.2 x 3.4 x 10.6 inches. Features: HF/VHF/UHF DSP Filters Dual Watch 0.1 Hz Tuning CTCSS/DCS Decode and Encoode Cross-band Full Duplex 1200/9600 Packet Ready It covers all of the normal ham bands in one package with virtually all modes! This one works 100% and looks like new. No defects. With paper work for $850. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 Technical Supplement for Yaesu FT-2700 Dual Band Mobile. Looks new. $20 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .

My beloved Yaesu FT-1000MP (the plain version, not a MkV or Field version) has suddenly developed a problem. The faceplate momentary contact "button" that transfers the VFO-A signal to VFO-B does not operate when I push it in. The button next to it that alternates the frequency from VFO-A to VFO-B and vice versa works fine. I do not hear a relay "click" then I push the VFO-A to VFO-B button like I do with the VFO-A alternating VFO-B button on the faceplate. I've done a factory reset a few times, inspected the radio's chassis, wiring, circuit boards and all looks fine. No smoke, crackles, sizzles, etc. I'm far from a repair expert regarding issue like this and would appreciate any help offered. Tnx, 73, Bill / w0bp

I have been using an Atlas screw type antenna for several years with my FT-857D mobile. Recently the antenna has failed to tune and when I push the tune button I only get a beep. I have tried two different mobile radios and atlas antennas. The radios are set to Atlas HF & 50. The voltage is showing 13.5 volts. Any information will be appreciated.

HF + VHF + UHF Transceiver, 2 meter Transceiver, Power Supply, Microphone, Manuals, and more For Sale: . Yaesu FT-847 HF+++ Transceiver: The Yaesu FT-847 changes base operation forever. Now you get three radios in one -- HF, VHF/UHF and satellite. You get 100 watt output on HF and 6 Meters, plus 50 watts on both 2 Meters and 430 MHz bands. Additional features include: Cross-band Full Duplex operation, Normal/Reverse Tracking, CTCSS/DCS Encode and Decode, 0.1 Hz tuning steps, DSP Notch, DSP NR and DSP BPF, Shuttle Jog Tuning Dial, Carry Handle and Keypad Entry. The FT-847 is also 1200/9600 bps Packet ready. 10.2 x 3.4 x 10.6 inches. Features: HF/VHF/UHF DSP Filters Dual Watch 0.1 Hz Tuning CTCSS/DCS Decode and Encoode Cross-band Full Duplex 1200/9600 Packet Ready It covers all of the normal ham bands in one package with virtually all modes! This one works 100% and looks like new. No defects. With paper work for $850. . Yaesu FT-1900, 55 Watt 2 m transceiver: The Yaesu FT-1900R provides toughness in a high performance 55 watt 2-meter FM transceiver. The receiver covers 136 to 174 MHz with illuminated front panel keys and 200 memories. You get CTCSS and DCS Encoder and Decoder circuits and keyboard entry of frequencies directly from microphone. 5.6 x 1.6 x 5.8 inches. The supplied MH-48A6J DTMF hand mic is backlit. It comes with the MMB-36 mounting bracket and DC cord. It requires 13.8 VDC at 11 Amps. Features: 200 Memories (6 Character) 8 Memory Banks 55 Watts Output Automatic Power-Off Automatic Repeater Shift DTMF Memories CTCSS and DCS Encode/Decode CW Trainer Severe Weather Alert Backlit DTMF Mic This one works 100% and looks like new. No scratches or defects. Buy it with DTMF Mic, power cord, mobile bracket, and paperwork for $100. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . TenTec 708A Desk Microphone: The 708 A desk mic is a standard desk mic. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. The 708 is a dynamic mic on a flexible goose neck and is entirely metal, with no plastic parts. It is similar to the TenTec 705 desk mic, but MUCH more heavy duty. This one works 100% and looks very close to new, with one exception. The little peg used for PTT has been broken. If you use VOX it will be just perfect for you, as it works great on VOX. Otherwise, you can activate the PTT switch with tip of a pen or a small screwdriver, or you could replace the switch. . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 Technical Supplement for Yaesu FT-2700 Dual Band Mobile. Looks new. $20 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here

I have for sale a Yaesu mobile mounting bracket that came with a FT7100 I purchased last year. It isn't exactly the MMB-36 but fits the radio and works with any other Yaesu that takes the MMB-36 which includes the FT1802/1900/3000/7800/7900/8000/8100/8500/8800/8900 and maybe others. It comes with screws to attach it to the radio, and screws to attach it to your vehicle or other location. I am asking $13 shipped in the US and can take paypal/check/MO. 73 John AF5CC Sent using Zoho Mail

HF + VHF + UHF Transceiver, 2 meter Transceiver, Power Supply, Manuals, and more For Sale: . Yaesu FT-847 HF+++ Transceiver: The Yaesu FT-847 changes base operation forever. Now you get three radios in one -- HF, VHF/UHF and satellite. You get 100 watt output on HF and 6 Meters, plus 50 watts on both 2 Meters and 430 MHz bands. Additional features include: Cross-band Full Duplex operation, Normal/Reverse Tracking, CTCSS/DCS Encode and Decode, 0.1 Hz tuning steps, DSP Notch, DSP NR and DSP BPF, Shuttle Jog Tuning Dial, Carry Handle and Keypad Entry. The FT-847 is also 1200/9600 bps Packet ready. 10.2 x 3.4 x 10.6 inches. Features: HF/VHF/UHF DSP Filters Dual Watch 0.1 Hz Tuning CTCSS/DCS Decode and Encoode Cross-band Full Duplex 1200/9600 Packet Ready It covers all of the normal ham bands in one package with virtually all modes! This one works 100% and looks like new. No defects. With paper work for $850. . Yaesu FT-1900, 55 Watt 2 m transceiver: The Yaesu FT-1900R provides toughness in a high performance 55 watt 2-meter FM transceiver. The receiver covers 136 to 174 MHz with illuminated front panel keys and 200 memories. You get CTCSS and DCS Encoder and Decoder circuits and keyboard entry of frequencies directly from microphone. 5.6 x 1.6 x 5.8 inches. The supplied MH-48A6J DTMF hand mic is backlit. It comes with the MMB-36 mounting bracket and DC cord. It requires 13.8 VDC at 11 Amps. Features: 200 Memories (6 Character) 8 Memory Banks 55 Watts Output Automatic Power-Off Automatic Repeater Shift DTMF Memories CTCSS and DCS Encode/Decode CW Trainer Severe Weather Alert Backlit DTMF Mic This one works 100% and looks like new. No scratches or defects. Buy it with DTMF Mic, power cord, mobile bracket, and paperwork for $100. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . TenTec 705 Desk Microphone: The 705 desk mic is a standard desk mic. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. It has an electret mic element so it has great frequency response. This one works 100% and looks very close to new, with no scratches or defects. The foam wind screen is even in good shape. With paper work for $75 . TenTec 708A Desk Microphone: The 708 A desk mic is a standard desk mic. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. The 708 is a dynamic mic on a flexible goose neck and is entirely metal, with no plastic parts. It is similar to the TenTec 705 desk mic, but MUCH more heavy duty. This one works 100% and looks very close to new, with one exception. The little peg used for PTT has been broken. If you use VOX it will be just perfect for you, as it works great on VOX. Otherwise, you can activate the PTT switch with tip of a pen or a small screwdriver, or you could replace the switch. It has no scratches or defects. The wind screen is in good shape, and it is still in its original box. Buy it with paper work for $79 Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH

Hello to the group I have FTdx3000 looking for recommendations microphone settings I have heil pr20 microphone any suggestions I would appreciate thank you have a good day

I just picked up a second hand FTM-350, with APRS and the GPS module installed. Hoping someone can help or at least offer some insight. I know this is an older, discontinued radio. For whatever reason, it seems I don't have dual receive capability. Both left and right receive work, but only on whatever one is the main (as indicated by the triangle). Sub-band mute is off. APRS modem is off. I've gone through the manual but haven't seen anything that seemed relevant. Was I reading the specs on this radio wrong and it doesn't actually have dual receivers? Perhaps I just need to perform a factory reset.

Hi all, I have a G2700-SDX in great condition, but the direction indicator no longer works on the control box. The rotor turns full CW/CCW but without the indicator I can't tell where.The plug on the motor is a 6pin, and the 2800 successor rotor now has a 7pin. Does anyone know if a controller from a 2800 or 1000 can be wired for the older 2700 (a comparison document made by Yaesu lists the 2800 and 1000 features as being shared). An email to Yaesu service in CA yielded nothing....they said they have no info on the 2700 (as if it were made by someone else). Any help appreciated. Idiom Press makes a board that gives the 2700SDX digital functionality, but it's not clear if the problem in the controller goes beyond a bad indicator. Possibly an RT-21 would work also, but trying to avoid that expense. 73 Darrell AB2E Rigs: FTDX-9000D, FTDX-9000C (100% upgrade to D with all options installed)

Hello Members - Why do I see that Yaesu uses a paragraph style, individual step by step documentation style for their Adjustment / Calibration procedures ( ie. FT-767GX and FT1000(d) , others ) ? Whereas, Kenwood and several other transceiver manufacturers use a Table or Spreadsheet style format for their units Adjustment / Calibration procedures. The Table format style appears much more appealing and easier to work with to self. Has anyone here attempted to convert the Yaesu Calibration/Adjustment paragraph's to a Spreadsheet or Table format or know of where to find a similar conversion ?

Just got a new FT710 and it is working fine, but in order to hook it to my laptop I need to install a virtual com port driver on the laptop. Has anyone out there had to do this to their laptop, and if so, what software worked for you? Thanks, Marc-k7wxk

2 meter Transceiver, Power Supply, Manuals, and more For Sale: . Yaesu FT-1900, 55 Watt 2 m transceiver: The Yaesu FT-1900R provides toughness in a high performance 55 watt 2-meter FM transceiver. The receiver covers 136 to 174 MHz with illuminated front panel keys and 200 memories. You get CTCSS and DCS Encoder and Decoder circuits and keyboard entry of frequencies directly from microphone. 5.6 x 1.6 x 5.8 inches. The supplied MH-48A6J DTMF hand mic is backlit. It comes with the MMB-36 mounting bracket and DC cord. It requires 13.8 VDC at 11 Amps. Features: 200 Memories (6 Character) 8 Memory Banks 55 Watts Output Automatic Power-Off Automatic Repeater Shift DTMF Memories CTCSS and DCS Encode/Decode CW Trainer Severe Weather Alert Backlit DTMF Mic This one works 100% and looks like new. No scratches or defects. Buy it with DTMF Mic, power cord, mobile bracket, and paperwork for $100. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . TenTec 705 Desk Microphone (fits Yaesu): - The 705 desk mic is the standard desk mic used with many TenTec rigs. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. - It has an electret mic element so it has great frequency response. - This one works 100% and looks very close to new, with no scratches or defects. The foam wind screen is even in good shape. - With paper work for $79/ . TenTec 708A Desk Microphone (Works with Yaesu): The 708 A desk mic is a standard desk mic used with many TenTec rigs. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. - The 708 is a dynamic mic on a flexible goose neck and is entirely metal, with no plastic parts. It is similar to the TenTec 705 desk mic, but MUCH more heavy duty. - This one works 100% and looks very close to new, with one exception. The little peg used for PTT has been broken. If you use VOX it will be just perfect for you, as it works great on VOX. Otherwise, you can activate the PTT switch with tip of a pen or a small screwdriver, or you could replace the switch. - It has no scratches or defects. The wind screen is in good shape, and it is still in its original box. - Buy it with paper work for $79. . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 Technical Supplement for Yaesu FT-2700 Dual Band Mobile. Looks new. $20 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .