开云体育

My beloved Yaesu FT-1000MP (the plain version, not a MkV or Field version) has suddenly developed a problem. The faceplate momentary contact "button" that transfers the VFO-A signal to VFO-B does not operate when I push it in. The button next to it that alternates the frequency from VFO-A to VFO-B and vice versa works fine. I do not hear a relay "click" then I push the VFO-A to VFO-B button like I do with the VFO-A alternating VFO-B button on the faceplate. I've done a factory reset a few times, inspected the radio's chassis, wiring, circuit boards and all looks fine. No smoke, crackles, sizzles, etc. I'm far from a repair expert regarding issue like this and would appreciate any help offered. Tnx, 73, Bill / w0bp

I have been using an Atlas screw type antenna for several years with my FT-857D mobile. Recently the antenna has failed to tune and when I push the tune button I only get a beep. I have tried two different mobile radios and atlas antennas. The radios are set to Atlas HF & 50. The voltage is showing 13.5 volts. Any information will be appreciated.

HF + VHF + UHF Transceiver, 2 meter Transceiver, Power Supply, Microphone, Manuals, and more For Sale: . Yaesu FT-847 HF+++ Transceiver: The Yaesu FT-847 changes base operation forever. Now you get three radios in one -- HF, VHF/UHF and satellite. You get 100 watt output on HF and 6 Meters, plus 50 watts on both 2 Meters and 430 MHz bands. Additional features include: Cross-band Full Duplex operation, Normal/Reverse Tracking, CTCSS/DCS Encode and Decode, 0.1 Hz tuning steps, DSP Notch, DSP NR and DSP BPF, Shuttle Jog Tuning Dial, Carry Handle and Keypad Entry. The FT-847 is also 1200/9600 bps Packet ready. 10.2 x 3.4 x 10.6 inches. Features: HF/VHF/UHF DSP Filters Dual Watch 0.1 Hz Tuning CTCSS/DCS Decode and Encoode Cross-band Full Duplex 1200/9600 Packet Ready It covers all of the normal ham bands in one package with virtually all modes! This one works 100% and looks like new. No defects. With paper work for $850. . Yaesu FT-1900, 55 Watt 2 m transceiver: The Yaesu FT-1900R provides toughness in a high performance 55 watt 2-meter FM transceiver. The receiver covers 136 to 174 MHz with illuminated front panel keys and 200 memories. You get CTCSS and DCS Encoder and Decoder circuits and keyboard entry of frequencies directly from microphone. 5.6 x 1.6 x 5.8 inches. The supplied MH-48A6J DTMF hand mic is backlit. It comes with the MMB-36 mounting bracket and DC cord. It requires 13.8 VDC at 11 Amps. Features: 200 Memories (6 Character) 8 Memory Banks 55 Watts Output Automatic Power-Off Automatic Repeater Shift DTMF Memories CTCSS and DCS Encode/Decode CW Trainer Severe Weather Alert Backlit DTMF Mic This one works 100% and looks like new. No scratches or defects. Buy it with DTMF Mic, power cord, mobile bracket, and paperwork for $100. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . TenTec 708A Desk Microphone: The 708 A desk mic is a standard desk mic. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. The 708 is a dynamic mic on a flexible goose neck and is entirely metal, with no plastic parts. It is similar to the TenTec 705 desk mic, but MUCH more heavy duty. This one works 100% and looks very close to new, with one exception. The little peg used for PTT has been broken. If you use VOX it will be just perfect for you, as it works great on VOX. Otherwise, you can activate the PTT switch with tip of a pen or a small screwdriver, or you could replace the switch. . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 Technical Supplement for Yaesu FT-2700 Dual Band Mobile. Looks new. $20 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here

I have for sale a Yaesu mobile mounting bracket that came with a FT7100 I purchased last year. It isn't exactly the MMB-36 but fits the radio and works with any other Yaesu that takes the MMB-36 which includes the FT1802/1900/3000/7800/7900/8000/8100/8500/8800/8900 and maybe others. It comes with screws to attach it to the radio, and screws to attach it to your vehicle or other location. I am asking $13 shipped in the US and can take paypal/check/MO. 73 John AF5CC Sent using Zoho Mail

HF + VHF + UHF Transceiver, 2 meter Transceiver, Power Supply, Manuals, and more For Sale: . Yaesu FT-847 HF+++ Transceiver: The Yaesu FT-847 changes base operation forever. Now you get three radios in one -- HF, VHF/UHF and satellite. You get 100 watt output on HF and 6 Meters, plus 50 watts on both 2 Meters and 430 MHz bands. Additional features include: Cross-band Full Duplex operation, Normal/Reverse Tracking, CTCSS/DCS Encode and Decode, 0.1 Hz tuning steps, DSP Notch, DSP NR and DSP BPF, Shuttle Jog Tuning Dial, Carry Handle and Keypad Entry. The FT-847 is also 1200/9600 bps Packet ready. 10.2 x 3.4 x 10.6 inches. Features: HF/VHF/UHF DSP Filters Dual Watch 0.1 Hz Tuning CTCSS/DCS Decode and Encoode Cross-band Full Duplex 1200/9600 Packet Ready It covers all of the normal ham bands in one package with virtually all modes! This one works 100% and looks like new. No defects. With paper work for $850. . Yaesu FT-1900, 55 Watt 2 m transceiver: The Yaesu FT-1900R provides toughness in a high performance 55 watt 2-meter FM transceiver. The receiver covers 136 to 174 MHz with illuminated front panel keys and 200 memories. You get CTCSS and DCS Encoder and Decoder circuits and keyboard entry of frequencies directly from microphone. 5.6 x 1.6 x 5.8 inches. The supplied MH-48A6J DTMF hand mic is backlit. It comes with the MMB-36 mounting bracket and DC cord. It requires 13.8 VDC at 11 Amps. Features: 200 Memories (6 Character) 8 Memory Banks 55 Watts Output Automatic Power-Off Automatic Repeater Shift DTMF Memories CTCSS and DCS Encode/Decode CW Trainer Severe Weather Alert Backlit DTMF Mic This one works 100% and looks like new. No scratches or defects. Buy it with DTMF Mic, power cord, mobile bracket, and paperwork for $100. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . TenTec 705 Desk Microphone: The 705 desk mic is a standard desk mic. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. It has an electret mic element so it has great frequency response. This one works 100% and looks very close to new, with no scratches or defects. The foam wind screen is even in good shape. With paper work for $75 . TenTec 708A Desk Microphone: The 708 A desk mic is a standard desk mic. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. The 708 is a dynamic mic on a flexible goose neck and is entirely metal, with no plastic parts. It is similar to the TenTec 705 desk mic, but MUCH more heavy duty. This one works 100% and looks very close to new, with one exception. The little peg used for PTT has been broken. If you use VOX it will be just perfect for you, as it works great on VOX. Otherwise, you can activate the PTT switch with tip of a pen or a small screwdriver, or you could replace the switch. It has no scratches or defects. The wind screen is in good shape, and it is still in its original box. Buy it with paper work for $79 Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH

Hello to the group I have FTdx3000 looking for recommendations microphone settings I have heil pr20 microphone any suggestions I would appreciate thank you have a good day

I just picked up a second hand FTM-350, with APRS and the GPS module installed. Hoping someone can help or at least offer some insight. I know this is an older, discontinued radio. For whatever reason, it seems I don't have dual receive capability. Both left and right receive work, but only on whatever one is the main (as indicated by the triangle). Sub-band mute is off. APRS modem is off. I've gone through the manual but haven't seen anything that seemed relevant. Was I reading the specs on this radio wrong and it doesn't actually have dual receivers? Perhaps I just need to perform a factory reset.

Hi all, I have a G2700-SDX in great condition, but the direction indicator no longer works on the control box. The rotor turns full CW/CCW but without the indicator I can't tell where.The plug on the motor is a 6pin, and the 2800 successor rotor now has a 7pin. Does anyone know if a controller from a 2800 or 1000 can be wired for the older 2700 (a comparison document made by Yaesu lists the 2800 and 1000 features as being shared). An email to Yaesu service in CA yielded nothing....they said they have no info on the 2700 (as if it were made by someone else). Any help appreciated. Idiom Press makes a board that gives the 2700SDX digital functionality, but it's not clear if the problem in the controller goes beyond a bad indicator. Possibly an RT-21 would work also, but trying to avoid that expense. 73 Darrell AB2E Rigs: FTDX-9000D, FTDX-9000C (100% upgrade to D with all options installed)

Hello Members - Why do I see that Yaesu uses a paragraph style, individual step by step documentation style for their Adjustment / Calibration procedures ( ie. FT-767GX and FT1000(d) , others ) ? Whereas, Kenwood and several other transceiver manufacturers use a Table or Spreadsheet style format for their units Adjustment / Calibration procedures. The Table format style appears much more appealing and easier to work with to self. Has anyone here attempted to convert the Yaesu Calibration/Adjustment paragraph's to a Spreadsheet or Table format or know of where to find a similar conversion ?

Just got a new FT710 and it is working fine, but in order to hook it to my laptop I need to install a virtual com port driver on the laptop. Has anyone out there had to do this to their laptop, and if so, what software worked for you? Thanks, Marc-k7wxk

2 meter Transceiver, Power Supply, Manuals, and more For Sale: . Yaesu FT-1900, 55 Watt 2 m transceiver: The Yaesu FT-1900R provides toughness in a high performance 55 watt 2-meter FM transceiver. The receiver covers 136 to 174 MHz with illuminated front panel keys and 200 memories. You get CTCSS and DCS Encoder and Decoder circuits and keyboard entry of frequencies directly from microphone. 5.6 x 1.6 x 5.8 inches. The supplied MH-48A6J DTMF hand mic is backlit. It comes with the MMB-36 mounting bracket and DC cord. It requires 13.8 VDC at 11 Amps. Features: 200 Memories (6 Character) 8 Memory Banks 55 Watts Output Automatic Power-Off Automatic Repeater Shift DTMF Memories CTCSS and DCS Encode/Decode CW Trainer Severe Weather Alert Backlit DTMF Mic This one works 100% and looks like new. No scratches or defects. Buy it with DTMF Mic, power cord, mobile bracket, and paperwork for $100. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . TenTec 705 Desk Microphone (fits Yaesu): - The 705 desk mic is the standard desk mic used with many TenTec rigs. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. - It has an electret mic element so it has great frequency response. - This one works 100% and looks very close to new, with no scratches or defects. The foam wind screen is even in good shape. - With paper work for $79/ . TenTec 708A Desk Microphone (Works with Yaesu): The 708 A desk mic is a standard desk mic used with many TenTec rigs. This one has an 8 pin plug wired for TenTec on it. This means it also fits Yaesu rigs with the round 8 pin plug. - The 708 is a dynamic mic on a flexible goose neck and is entirely metal, with no plastic parts. It is similar to the TenTec 705 desk mic, but MUCH more heavy duty. - This one works 100% and looks very close to new, with one exception. The little peg used for PTT has been broken. If you use VOX it will be just perfect for you, as it works great on VOX. Otherwise, you can activate the PTT switch with tip of a pen or a small screwdriver, or you could replace the switch. - It has no scratches or defects. The wind screen is in good shape, and it is still in its original box. - Buy it with paper work for $79. . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 Technical Supplement for Yaesu FT-2700 Dual Band Mobile. Looks new. $20 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .

I have acquired a Yaesu ft-50r. It will not power on. If I pull the main board out and attach a power source I move a piece of metal across the wires on the motherboard and start the radio. Then moving the wire across the switch will not turn the radio off.If I quickly reassemble the radio and attach the battery, the radio will still be on. I can transmit, it receives. I can alter the squelch level ( I broke the speaker leads when I pulled the boar, so I can't hear the radio at the moment). If I then push the power switch, the radio will turn off, but I cannot turn it back on. I have seen this problem addressed in some very old posts using a circuit writer pen to coat the bottom of the switch. I am not sure if the entire bottom gets coated or only a portion. Has anyone heard of this problem with the 50r and if so, how it was fixed? Thanks -- Rick, KK4GGL

Hi I received this TRX a few days ago and during the first tests I realized that it doesn't work in TX in the spectrum section as mentioned in the object. They practically remain uncovered the 30 and 20 meter bands, on the others bands apparently OK. For example, up to 14500 khz it does not transmit, from 14501 it transmits. Have you had any experience with this issue? Thank you

And ... Looking at the thread title, I can see something that may have caused some confusion... ... the radio is an FT-50r -- KK4GGL

I have acquired an FT-80r. The battery (FNB-41xh Ni_MH)is dead (measured with a multi-meter). The charger that came with it is an NC-60B (for Ni-CD). The charger tested as putting out the specified voltage/amperage. I have DLed the manual. the NC-60B is mentioned, as are Ni-CD batteries. Ni-MH aren't mentioned anywhere. Anyone know if I should be able to power up the radio with the charger plugged in, but no battery. Is it OK to charge Ni-MH batteries with the NC-60B Ni-CD charger? Any ideas on how I might power up the radio without a battery? Any and all help appreciated.

I recently picked up a DMU-2000 to go along with my FT-2000D. When I connected it, I found that the 2023 CMOS battery was completely dead which cleared any BIOS settings in the DMU. I replaced the 2023, was able to get the time to stay correct, but the DMU still will not boot. It displays the two horizontal bars from the OS boot process, but instead of the main DMU screen appearing, it instead turns itself back off. I believe that possibly one of the BIOS settings needs to be changed so that the boot process will complete, but can't figure out which. The ham that sold it to me claims that it was in fact working when he sold it to me, but I'm not getting very far with that. thanks in advance Dave, N2EPV

Hi all, new to the group. I have a Yaesu FIF-232C but it came without the 6 pin to 6 pin DIN cable so I will buy one, can anyone confirm that it is in fact pin to pin straight through wiring? Thanks for any help. Adam Farber W4AJF Cooper City, FL

Hi all, new to the group. Can anyone tell me in the 6 pin Din to 6 pin Din cable for the Yaesu FIF-232C is pin to pin? I am looking to by a couple of them. Thanks for any help. Adam Farber W4AJF Cooper City, FL

2 meter Transceiver, Power Supply, Crystal filters, Manuals, and more For Sale: . Yaesu FT-1900, 55 Watt 2 m transceiver: The Yaesu FT-1900R provides toughness in a high performance 55 watt 2-meter FM transceiver. The receiver covers 136 to 174 MHz with illuminated front panel keys and 200 memories. You get CTCSS and DCS Encoder and Decoder circuits and keyboard entry of frequencies directly from microphone. 5.6 x 1.6 x 5.8 inches. The supplied MH-48A6J DTMF hand mic is backlit. It comes with the MMB-36 mounting bracket and DC cord. It requires 13.8 VDC at 11 Amps. Features: 200 Memories (6 Character) 8 Memory Banks 55 Watts Output Automatic Power-Off Automatic Repeater Shift DTMF Memories CTCSS and DCS Encode/Decode CW Trainer Severe Weather Alert Backlit DTMF Mic This one works 100% and looks like new. No scratches or defects. Buy it with DTMF Mic, power cord, mobile bracket, and paperwork for $100. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . Astron RS-20 A, 20 amp Power Supply For Sale: This power supply is useful for Amateur Ham Radio applications, a test bench, or any place where regulated 13 V DC is needed at fairly high current. Astron power supplies feature solid-state electronic regulation, EMI filter, fold back current limiting for protection from excessive current and shorted output. Input voltage is 115 VAC 50/60 Hz. Crowbar over voltage protection is also provided. These high quality power supplies are manufactured in the U.S. The RS-20 A is rated at 20 amps intermittent use, and 16 amps continuous duty. The output voltage can be internally adjusted, as can the current limiting. This particular supply works great. It only varies 0.01 Volts with a load! Cosmetically it looks really great. It does have a Yaesu label on it, which I will leave in place. With paper work for $70 plus shipping from Florida, or pick up near Ocala, FL. . Yaesu Crystal Filters These fit the FT-1000 series, among others, and are for the 455 KHz IF. XF-455K-202-01 2000 Hz wide for SSB $85 XF-455K-501-01 500 Hz wide for CW $110 . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .