开云体育

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Re: Resistor for block detection, best size?
Seven months ago I sent an email to Karst about some testing I did on my DR5088RC unit.? Was having the problem with reliable sensor contact. I do use Railcom on my railroad using JMRI. My Railroad
By Dennis Cherry · #4712 ·
Re: Resistor for block detection, best size?
Heath For DR4088LN-CS a 10k resistor should work perfectly. Different systems often require different values and you cannot read across from different systems to get the value for your feedbacks.
By Iain Morrison · #4711 ·
Resistor for block detection, best size?
I have both the DR4088CS and the YaMoRC equivalent. On the DR4088CS I have added the resistors as recommended. What is the best size resistor to use for wheelsets on N scale? I thought everyone used
By Heath @ Human[c]ity Junction · #4710 ·
Font size
Is there any way to increase font size in YD7010 log screen? My eyes are not what they use to be and have a hard time reading the log on screen. Thank you.
By Ivan Bondy · #4709 ·
Re: YD7403 and Loconet B
A bit more research shows that Loconet B is required for the YD7403 and DR5033 boosters but the YD6016LN-CS/GND can operate on either Loconet T or Loconet B. It's only Loconet throttles or anything
By Oldngrey · #4708 ·
YD7403 and Loconet B
I need some help with connecting up Loconet T and B sockets on the YD7001. I was under the impression that the Loconet B connector was to be used to connect up booster modules and the Loconet T
Re: Detailed setup manual for the YD7010?
Novice here.? So programming the decoder with DecoderPro totally completes the job?? I would not need to go through decoder programing in YD7010 or in the Z21 app?? If so, eliminates redundant
By Rick Norell <ricknorell@...> · #4706 ·
Re: YD7001 stuck in demo mode etc.
Hi John I did that and it was not in there, thanks any way. Just posted it back to dealer.
By terry lee · #4705 ·
Re: YD7001 stuck in demo mode etc.
Did you check your junk folder.? I had a similar problem.? It turned out I got the code several times but it went into the junk folder and I failed to notice.? My bad but it fooled me for a few
By John Pollard · #4704 ·
Re: YD7001 stuck in demo mode etc.
I never received the activation code message despite requesting it, that may be the problem !
By terry lee · #4703 ·
Re: YD7001 stuck in demo mode etc.
Reinstall the drivers by right clicking the installer, and selecting ‘Run as Administrator’.
By PaulR · #4702 ·
Re: Detailed setup manual for the YD7010?
JMRI does do the actual programming, it only provides a pictorial and textual human interface to your command station. The command station - in your case a YD7010 still does the actual programming and
By Iain Morrison · #4701 ·
Re: Detailed setup manual for the YD7010?
Karst, thank you for the latest manual!? If I purchase, I will be a very basic user.? I have no legacy dcc equipment to consider.? I want walk around locomotive control using wifi and basic DCC?
By Rick Norell <ricknorell@...> · #4700 ·
Re: YD7001 | Resetting Command Station after Short
Glad to see you managed to RTFM. Shorts. These are not "normal". My system runs very well without them...... If you are getting shorts for any reason, then you need to understand why and then take
By Pete S. · #4699 ·
Re: YD7001 stuck in demo mode etc.
Hi Iain I did that 4 times with 2 PCs same result, may have been a faulty YD9401. Now given up on it and going back to my old Digitrax.
By terry lee · #4698 ·
Re: YD7001 stuck in demo mode etc.
It sounds very much like you do not have a connection from the PC to the YD7001. I suggest that you re-install the YD7001 software on you PC and make sure you agree to all the drivers being
By Iain Morrison · #4697 ·
Re: YD7001 stuck in demo mode etc.
Also the built in Throttle did not work.
By terry lee · #4696 ·
Re: YD7001 stuck in demo mode etc.
I managed to get the YD7001 after many hours work to get it on but having tried to connect a Z21 WLNA MAUS to the YD1001 it did not work . All settings were correct but no luck, also tried a Digitrax
By terry lee · #4695 ·
Re: Detailed setup manual for the YD7010?
Hi, it's there, but still only in German: YD7010.Konfig.de ( http://www.yamorc.de/manuals/YD7010.Konfig.de/index.html )
Re: YD7001 stuck in demo mode etc.
Demo mode means no USB connection. 1) drivers not/not properly installed 2) USB connector nor fittet "deep" enoug in the DR500's socket 3) USB cable damaged/charge-cable instead of data-cable 4) USB
By karst.drenth · #4693 ·