开云体育

Thanks! My house here in Napa is in escrow, and we are getting an apartment in Union, MO, while we house-hount in Washington, MO. One thing about the area is that many or most homes seem to be

Good luck with your move Allen. If you come across some gear that is a bit less than retail quality that you don't want to drag cross country let us know. I love the AIO you sold me (and all the TT3s,

Nothing that you guys didn't mention, mostly operator error. 1. I was using the wrong driver for the cable. 2. I tried to use my good old RealTerm software with the Trippel Esc protocol. 3. It was

Joe, Just out of curiousity, what was the issue? At any rate, I am glad your old unit is back in service!? 73, Allen AF6OF

Thanks! It’s up and working like new. There were multiple issues and you folks named all of them. 73, Joe, N7IV

What he said! Some TT3's and some old AIO's use a PIC16F644. Newer versions use a PIC16F1827. The newer chips are drop-in compatible with older gear, but not the other way around, as the 644 used a

Joe, There is no problem replanting the PIC in a TT3 to try to configure it. If I understand your statement about the function of the unit, and it transmits about once per second after powering it

Sounds like either a power issue or RF issue which is causing the unit to constantly reset.Two things to try here:?? Connect to a dummy load and see if the behavior changes.???????? For

Allen, Thanks for the great advice! That all made sense. I downloaded (and installed) the proper driver and program from Byonics. Then I wiggled/pushed the plug quite a bit. Still no joy.

There is a version of thr TT3 with firmware setup for Peet and other weather stations. I'm using it with a Baofang for our Club's weather station. It has been running for at least 5 years. It's

Hijacked Topic now a separate thread. The TT4 is capable of both DIGI and Wx functions - you even acknowledge you had one doing that at your home station. The only question is that is Wx Trax?? Is

Guys, I have a simple question. Our Club has had a Peet Bros 100 and a WX Trax running for several years (K4PAR-1). I believe that several years ago I also had a TT4 running as a WX station (Peet

Joe, You cannot program the MT-AIO with a terminal program; you will need to use the TT3 config program:?https://byonics.com/downloads/TinyTrak3_Config_v1.4.6.zip? Also, you will need to download

I’m working with an older version of the micro trak AIO (version 1.4.4 on circuit board) trying to change the callsign in its program using “Real Term,” and I have a failure to

I didn't realize the MT-2000 had a different configuration style than the other MicroTrak and TinyTrak products. Sorry for the confusion! ------- Rob KB8RCO

The MT-2001 is a little different from? a TT3 or TT4. You do not ( and should not) enter the bootloader for any purpose other than reloading the firmware from a terminal program, or checking to make

If there were a way to add a momentary (Normally Closed) switch on the 5V pin 4 of the TT-USB inside the DE9 case, that would make this device ideal. Pressing the switch would allow the user to

In order to get the Config area functions, you must place the TinyTrak device in "boot loader" There are two important things that are required for "boot loader": 1. COMM port must match the USB

Hello, I have a MicroTrak 2001 and am using TinyTrak3Config v1.4.6 to configure it.? However, when I "read version" or "read config", I get a "TinyTrak3 not found ()" error.? The MicroTrak is

I don't see how an APO3 cutting off power would cause a problem with the TinyTrak.? It is no different that connecting and disconnecting power.?? Was the transmitter on the same APO3??? ??