¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date
Re: Fuel Injector choices...
FWIW... http://www.youtube.com/watch?NR=1&feature=endscreen&list=PLBB1FF4A6D8EE1C94&v=7aT4S1lIBAY
By Neil <furrylittleotter@...> · #63669 ·
Re: Exhaust by Vanaru
Car, Small ..... military speak?
By Craig Morton · #63668 ·
Re: Exhaust by Vanaru
"CS"?
By Jake de Villiers · #63667 ·
Re: Exhaust by Vanaru
My stainless steel CS header has been used for 6 years on hiways, washboards, dirt, sand and mud for 6 years no cracks no problems and no flaking coatings i have flex tube welded into J-pipe Leon
By Leon Korkin · #63666 ·
Re: Exhaust by Vanaru
Forgot to mention that it's an '89 Westy with '91 ej22 with smallcar mount. Bob, Can you tell me where you got the mild steel header? How much?
By ryan_99juliet · #63665 ·
Re: Exhaust by Vanaru
and will last a long time. For some reason, these conversion exhaust systems don't seem to tolerate the needed design changes AND the use of SS. I've had this experience with SS on 2.2 and 3.0 Subaru
By Bob Stevens · #63664 ·
Exhaust by Vanaru
I'm fed up with my small car exhaust header that cracks if you look at it! Does anyone have first hand experience with Vanaru's exhaust headers? Any problems with cracking? Rusting? They are $200 more
By ryan_99juliet · #63663 ·
Re: help with 3 codes
i am only getting 16 regardless of highway or city. I have go westy 15 inch rims but was hoping to get better mpg then 16. i am going to call smallcar on monday and ask them about the codes. i have
By theoldred90 <tbmccarney@...> · #63662 ·
Re: Thoughts on aluminum crank pulley
Are you short on power now ? if there is any difference .....it will be .002 % ( point zero zero 2 percent ) increase. a lighter mass in the crankshaft assembly doesn't actually increase hp .. it can
By Scott Daniel - Turbovans <ScottDaniel@...> · #63661 ·
Re: hard start symptoms, intermittent, no cel hooked up.
if I suspect fuel getting in when it shouldn't .. I would go directly the seals at the bottom of the bowl each injector sits in . If those leak .. and they do deteriorate .. fuel goes right into a
By Scott Daniel - Turbovans <ScottDaniel@...> · #63660 ·
Re: Thoughts on aluminum crank pulley
Matt: You could probably use more rotating mass, not less. Craig
By Craig Morton · #63659 ·
Re: Thoughts on aluminum crank pulley
Snake oil. Larry H.
By Larry Hamm <Patlar@...> · #63658 ·
Thoughts on aluminum crank pulley
Just wondering what everyone's thoughts are on aluminum crank pulley. A co worker recommended I get one because of weight and increase in horse power. Thanks, Matt
By Matt · #63657 ·
Re: hard start symptoms, intermittent, no cel hooked up.
Sounds like a classic case of over fueling. When you hold throttle in WOT the ECU runs in 'clear flood' mode. That is, the injectors do not fire until engine rpm's reach a target speed of over 600 rpm
By dk · #63656 ·
Re: hard start symptoms, intermittent, Now with cel (thanks Tom)
I probably should have mentioned somewhere in there, this is a 4 speed vanagon, 1985, with a 1994 ej22
By dmz <dmzwesty@...> · #63655 ·
Re: hard start symptoms, intermittent, Now with cel (thanks Tom)
With huge thanks to Tom Shiels, I now have a cel! (think of Tom Hanks on the beach "I ! have FIRE!" anyway..Lots of codes. Black only (stored codes) 21, 24, 35, 13 Green only, and at idle only, just
By dmz <dmzwesty@...> · #63654 ·
Re: Looking for 'Flip Kit' Advice
Ok, found it http://www.rjes.com/html/throttle_body_reverser__-_99_.html Rob becida@...
By Rob <becida@...> · #63653 ·
Re: help with 3 codes
Just curious what kind of mileage you are getting. Thanks Jimmy --- VW/Porsche Type4 Air Cooled 2270cc-175HP / 165lb Torque motor waiting to go into some kind of a van. -- I've come to the end of the
By Jimmy Gouge <jimmygouge@...> · #63652 ·
help with 3 codes
Hello, I have 3 codes that I cannot get rid of. A little help please 1985 auto -- 1996 subaru 2.2 - i have the small car Interface Board P0453 - Evap system pressure sensor high input p1101 - neutral
By theoldred90 <tbmccarney@...> · #63651 ·
Re: Looking for 'Flip Kit' Advice
Richard at RJES does one and owning one myself I can say that they are excellent quality and do the job great.
By Ian Speakman · #63650 ·