开云体育

Isak: Is this with CV disabled? It still halts hard, then corrects??? Thanks, Art www.artofcnc.ca

I tried r1.0 and I'm sorry to say that it has the same problem. Thanks, Isak.

Art: my codes are written with G1,I have noticed that if i use a smoother raster to vector conversion the speeds will increase with no problem,it seems to me that there are to many codes for so little

Hi Art; I have been using Programmers File Editor on Mach2 all along. Great editor for loading large files > 10meg. I checked logic page and path to editor was right. I clicked on browse and

Steve: Yes, new driver is included in the release. Good luck with the tests... It does sound like maybe a stall, no fucusing needed with those type of sensors. Thanks, Art www.artofcnc.ca

Cheers Art - I'll give that a try in the morning. Has it got the fixed Mach2.sys file as well? I don't think there was a missing pulse - scopes still on it. I think what happened was initially spindle

Bob: Now having some trouble with having my editor come up when in Mach2. Make sure that the editor is pointing to the right program location in the logic settings. I usually use notepad, some other

Hi Art; G61 & G64 now work as expected on my machine. CV can be toggled on and off in the same program. Also when G61 or G64 is entered on MDI screen it now toggles the state screen settings. Now

Steve: Current R1.0 just uploaded has the toolchange bug repaired. Only one press is necessary after the toolchange. Thanks, Art www.artofcnc.ca

Steve: Current Spin Count 4763 5440 ->11128<- 5305 Spin adder 2521 1828 701 2542 Thanks , looking into it. That third reading indicates a missing pulse. I had the same thing for awhile, it was my

Bob: ( And Izak). CV had a major problem. It is fixed and can be downloaded now in r1.0. Changing between G8 and G9 ( or G61 and G64) could be ignored under certain circumstances. (This included

Thanks for the driver, still some problems You forgot to fix 2 start/run presses after toolchange and lathe macro. The two key presses is causing a problem, sometimes lines only partly execute and

Bob: Sounds like a bug to me. When you change the CV mode on the state tab, it changes a single varibale in the program. That varibale also controls the LED now on the main page. If the LED lights,

<SNIP>. I am a victim of unexpected success on this project sorry many fronts </SNIP> That will teach you to go and write a program that works! Schitzoid and Programmer fit well in the same sentence

Hi Art; When I set Exact stop on state tab and put a G64 in the program my machine still runs in Exact stop mode. Led lights to indicate CV mode but machine is still running in Exact stop mode. If I

No, they are rapids? Unless you set new feeds approach and withdraw will be at threading feed speed - Bloody slow ;) Explanation of each move after each line Move to approach position Move to thread

Hi Steve; Why all the G0 moves? Shouldn't these be G01 moves? Bob Harvey

To be more precise, I hadn't figured for Step/Dir Spindle while threading....Completely a mistake on my part. I will send you a driver right away that should work... Art www.artofcnc.ca

Steve: Ahhhhhhhhhhhhhhh, now I understand. I really screwed up, I didn't allow for a Mach2 controlled spindle speed....(I was using a manual spinlde control....) I will fix right away.... thanks, Art

Yes - spindle motor is stopping! Here's the relevant lines, the next lot just increment X N130 M6 T2 N140 G43 H2 N150 G0 X9.73 Z36.386 S500 M4 M8 N160 G0 X7.191 Z34.978 N170 G32 X7.191 Z19.698 F1.0