开云体育

ctrl + shift + ? for shortcuts
© 2025 开云体育
  1. MachCNC
  2. Messages
Expanded Topics Messages Polls
Date
Re: Mach3 pwm Spindel analog Output csmio

 

Hi Sven
?
Are you controlling an ac motor via VFD or a DC motor from a controller ?
?
search in the top search box for message? ?
read replies from Peter Homann regarding supply of the 10v.
Peter is highly rated for his expertise so take his advice seriously.
?
Marcus
Re: Mach3 pwm Spindel analog Output csmio

 

Hello my name is Ed and I have a small cnc router and it was working fine and then I broke some pins and ordered a new control box and every since then it doesn't work right.
I live in Troy Mo. and would gladly pay someone to help me get it going again. Thanks I think it's a mogul. 636-358-1088
On Thursday, April 3, 2025 at 09:53:06 AM CDT, s.treese via groups.io <s.treese@...> wrote:


Hey all?
Does anyone here use a csmio-ip-s or similar controller under mach3 ??
How do I configure the 0-10v pwm signal on analogue out ??
Configuring a porentionmeter(analogue in) was no problem?
But I do not get an output signal?
Greetings Sven?
Mach3 pwm Spindel analog Output csmio

 

Hey all?
Does anyone here use a csmio-ip-s or similar controller under mach3 ??
How do I configure the 0-10v pwm signal on analogue out ??
Configuring a porentionmeter(analogue in) was no problem?
But I do not get an output signal?
Greetings Sven?
Re: Mach 3 Mill, Exact stop

 

Stopping after each g-code line is what mach-3 does when it is in single step mode.? Check your setup and config file to make sure this is not the case.
Re: Mach 3 Mill, Exact stop

 

Code block, I mean each individual instruction. No its not mechanical, I have a hand controller and motion is smooth and and calibration is very good.?
?
I thought originally it was a PC issue, then replace the box, motion under code is just the same.
?
Ideas???
Regards
Graham
Re: Mach 3 Mill, Exact stop

 

Hi Graham, not sure what you mean by each code block.? One thing you might check is to see if the machine is slipping steps due to binding or excessive friction.? Sam
Re: Mach 3 Mill, Exact stop

 
Edited

My thoughts as well. Alt-N or the button on the tool path screen will toggle it. When it is on the yellow LED above the button will flash.
Re: Mach 3 Mill, Exact stop

 

Haven’t got single block mode turned on?
Mach 3 Mill, Exact stop

 

I have re commissioned my 3 axis mill, All goes well, Except!!!
The machine stops at each code block. Appears if smoothing, forward looking is not working. I have changed the CV Control settings, made no difference. Selected Constant Velocity/Exact Stop. Bought a new computer , thinking the older one was not up to the task. Made no difference.
?
Can you offer any ideas???
?
Regards
?
Graham
?
?
Updated photo album Fraser CNC #photo-notice

Group Notification
 

fraserneville@... updated the photo album Fraser CNC : Some views of my 3D printed machine. The controller is an Arduino using the V3 controller board and my old drivers. Bed area is about 400 X 600mm Z is about 80mm
Re: Leaving MachCNC behind me.

 

I've just added a folder with 5 pics.
?
cheers
?
N
Added photo album Fraser CNC #photo-notice

Group Notification
 

fraserneville@... added the photo album Fraser CNC : general view of my #D printed machine.
Re: Leaving MachCNC behind me.

 

开云体育

ANy pic's of yer new setup ?

thanks

animal

On 12/9/24 12:42 PM, fraserneville via groups.io wrote:

Hi all.
?
Firstly, thanks to all those whose advice helped me all those years ago setting up my first CNC machine.
?
Two disasters impacted my early use- my laptop with a parallel port got stolen and the insurance wouldn't replace it with a similar item.
?
I solved this by building a desktop using a core board that included parallel. Unfortunately, a mouse plague meant that the innards of this got eaten and wrecked.
?
When researching a replacement, I found that for my needs at least it was cheaper and easier to use Open-Source, USB oriented software now.
?
I had dismantled my original CNC and rebuilt it with one using 3D printed parts. This one is bigger and more accurate.
?
Anyway, thanks again to the community and good times with your CNC-ing!
?
Cheers,
?
Neville
?
Leaving MachCNC behind me.

 

Hi all.
?
Firstly, thanks to all those whose advice helped me all those years ago setting up my first CNC machine.
?
Two disasters impacted my early use- my laptop with a parallel port got stolen and the insurance wouldn't replace it with a similar item.
?
I solved this by building a desktop using a core board that included parallel. Unfortunately, a mouse plague meant that the innards of this got eaten and wrecked.
?
When researching a replacement, I found that for my needs at least it was cheaper and easier to use Open-Source, USB oriented software now.
?
I had dismantled my original CNC and rebuilt it with one using 3D printed parts. This one is bigger and more accurate.
?
Anyway, thanks again to the community and good times with your CNC-ing!
?
Cheers,
?
Neville
?
Re: script brain

 

Hello everyone
I'm struggling with my brain, but I've made progress. My relay works as I want, but I'm stuck on the lighting of the led linked to the relay.
This led has the code OEMled=1011 and I would like it to light up steadily
Thanks in advance for your help
++ Gilles
Re: script brain

 

hello
thanks for the macro example
i will read this carefully and i will not fail to come back to you
as my english is mediocre i will tie myself in knots
++
gilles
Re: script brain

 

On Wed, Sep 18, 2024 at 04:14 AM, Stephen Muscato wrote:
?
hello everyone
in the meantime, I racked my brain :o) and I managed to make my relay work
I just renamed the OEM code of a led
on the "Ports and Pins" side I understood their usefulness to do external actions
thanks for the info
++
gilles
Re: script brain

 

I have various macros and have attached a pdf of them that may help you sort it out. You will need to get the Input and output numbers from the mach3 manual.

Macros for manual 2019_06_14.pdf
Macros for manual 2019_06_14.pdf

Re: script brain

 

I wrote a script many years ago and don't remember much.
Have you tried "Ports & Pins" you can select outputs there.

Could you describe in more detail what you are trying to do? I understand activate a relay, but "when a led is on" I don't understand.

Steve



On Monday, September 16, 2024 at 06:51:42 AM CDT, perso.gilles via groups.io <perso.gilles@...> wrote:


hi
i'm starting the brain script and i'm stuck on how to activate a relay when a led is on
a helping hand please
++
script brain

 

hi
i'm starting the brain script and i'm stuck on how to activate a relay when a led is on
a helping hand please
++
1 - 20 of 155599