开云体育

I have a TMG707 and DRA-50 for vara. Is there any way to control frequency and band from the computer interface?

Hi All, I'm seeking help on the installation of a Piexx.com interface board (IF-10A/B/C) into my old TS 140. A few months ago when I received the board I installed it as per the instructions and as it

Thanks Bob, This is a very recent to me 850s. I removed the bottom cover and all was revealed. The 2.7KHz filter is soldered in. Additionally there are two optional locations to install

You can install the 1.8 in the 500 slot. That way you have the factory 2.7 and the aftermarket 1.8. I read this somewhere, can't remember where, Kenwood claims if both 2.7's are used (455 and 8.8) at

Hi, I have a TS-850s with? the standard ssb 2.7KHz 8MHz filter installed. If I were to install the narrow ssb 1.8KHz 8 MHz? filter can I leave the 2.7 KHz installed or must I switch it? If both are

THANKS Charlie,I sent a message to Clairmont -- tried to send via web site to burghardt but nothing worked on their web site so sent an email.? Have to see.? I know like impossible to know what

I have been researching Kenwood repairs as I think I'll be needing as well. In this order, I have: http://www.midwest-technical.com/ Unfortunately, Tim is closed until the middle of April, but I

Looking for someone who repairs this unit.? I live near Sacramento CA but anywhere fine.? Let me know if you can recommend someone. LFibich@...: Larry F. W6EF

Hi Donald, You have a nice line up of radios there Donald. I always think of Icom as the cream of commercially made rigs. (Not counting K3's or Tentec). You are lucky to have a club house our regular

Richard . . . <kairos1@...> wrote: Glad it will work for you. I have two sets of paddles but use my straight keys most of the time. My everyday radio shifts between my Icom 7300

Hi Donald, Many thanks for the prompt reply to my Question. It was good of you to go to the trouble of finding the page in the instruction manual. I looked at the specification sheet but could find

Richard . . . <kairos1@...> wrote: It looks to me that you have to go into menus to adjust CW speed: https://www.manualslib.com/manual/903345/Kenwood-Ts-590sg.html?page=42 I

Hi , My trusty TS440sat has a fault and was thinking of upgrading to TS590s (Not SG). I am solely CW and want to know if there is a knob to change the WPM speed? I do not want to go into menus to

My TH-D7 seems to have become unable to charge either one of its battery packs through the power port on the radio. I have the original NiCd pack and an aftermarket NiMH battery pack. With the

Kenwood Dual Band HT, Crystal Filters, Mobile mount, Extension feet, and more For Sale . Kenwood TH-G71 Dual Band HT: The Kenwood TH-G71A is a dual bander with all the right features. Besides

Thanks Jeff... 73...Jordan VE6ZT

You can buy these parts in several places https://www.rfparts.com/diodes/diodes-pin/rls135.html https://www.veswin.com/product-RLS135-TE-11.html Even on

Hi group... Does anyone know if there is a replacement/substitute for the RLS135 and similar diodes used in these rigs...? Maybe something which can be used in a pinch for testing...? I can't get

Hello from Canada I have a TS-950SDX which has developed an intermittent problem lately. I'm listening to the band in question (it could be any band) when quite randomly the speaker suddenly goes

2 meters at 250 watts is not the same as HF at 100 watts; 100 watts on 75 meters would get into my telephones and set off my security system.