开云体育

It looks like you didn't select a patch to apply. Highlight the patch you would like to apply and then click "apply patch" -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

I ran into this very issue yesterday. My issue was I had filters turned on. Verify that you don't have any filters engaged that might interfere with incoming packets. -- 73, de KM4ACK YouTube (

Hey everyone... So, I've been trying to play a little bit with getting my IC-705 to work with Direwolf & Xastir. In addition to Jason's vids, I've also found this site helpful:

Unit hostapd.service could not be found get this when i run this sudo /usr/bin/autohotspotN

Hi Jason, Running The Update tool and invoking the Patch Tool ends in an endless loop at the end of the Update Tool beginning with the following window: The work around I am using is to "X" out of the

I'm not sure about the TS-2000 DB-9 port; but using the FT-847 I have needs using a NULL-modem ( reverse TX /RX < pin #2 and #3 on a DB-9 > you might check the pinout on the TS-2000 ..... just a FYI

Cross posting to see if anyone has any input. ---------- Forwarded message --------- From: James French <w8iss1@...> Date: Sun, Sep 12, 2021, 11:55 Subject: Sub RS-232 adapters and Kenwood

My Pi3B stopped seeing the gps even after a clean rebuild of the entire system.? I found the fix in this video: https://youtu.be/YIIC-iT6H-s ( https://youtu.be/YIIC-iT6H-s ) When I reinstalled GPSD

When I first built the Pi4B with BAP 3.08, the frequency would populate into the Pat window box but a red line would appear through the box with an error message indicating a failure to communicate

Patch now available :-) I also created an issue ticket so this can be addressed in a future version of BAP. https://github.com/km4ack/pi-build/issues/301 -- 73, de KM4ACK YouTube (

I tried to enable wifi thru raspi-config say could not see the adapter, then open the wpa_supplicant.conf? file removed the entries for the hot spot. rebooted was restored

Rig control staying red in Conky indicates that it isn't running. If it isn't running, Pat will not be able to control the rig. If you run into the same thing on the new system, let me know. I

Hi Jason it does put the freq in the block and with a line through it but then in the black screen it also say it cant connect which i assume is via ip to the flrig package Also rigcontrol on conkey

It will throw a wrench into things if everything isn't connected. Direwolf expects a sound card to be connected when it starts. Double check me but it looks like the Signalink supports your radio.

In the pat connect screen does the frequency populate into the box when you choose an alias? If so, does the box turn green or red? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

Currently only one patch at a time can be applied. Feel free to submit a feature request ( https://github.com/km4ack/pi-build/issues ) and I can look at applying multiples in a future release. -- 73,

Try disabling the hotspot. Open Hotspot Tools and then choose Disable Hotspot. Follow the instructions. After reboot, you should be able to use the GUI to connect to your local WiFi. A complete guide

By running: *ls /dev/serial/by-id/* you will find there are two listings for the 705 which are something similar to: usb-Icom_Inc._IC-705_IC-705_12007996-if00 usb-Icom_Inc._IC-705_IC-705_12007996-if02

Jerry, I received your email but it has been a couple of crazy days for me. I'll review the fix you submitted and see if I can get a new patch out in the next few days. -- 73, de KM4ACK YouTube (

Hi Paul, I've been out on a ham exercise all day and am exhausted.? I will try tomorrow to see what I am doing that is different than you. For the moment, I can tell you the single USB cable