开云体育

Oh, I think the line you see going across the rotor is the edge of the plating. Only half of the rotor and stator are plated. The stator is plated on the bottom. The rotor is plated on the inside

No. Walt Cates, WD0GOF https://wd0gof.com/Hallicrafters A majority of acceptance is not proof of correctness. https://wd0gof.com/bible-study/commentaries/ ________________________________ Sent:

Thanks C, I don’t recall seeing one like this. Your pic gives me a much better idea about its construction. I can just make out a line going across, almost thru the center, but I can’t understand

There is no room to move the cap to line up. It would stick out of the PA cabinet. Any lower and it his the Tune cap. Its really tight in there Walt. I will figure something out! We must save this

Have you looked at the possibility of moving the mounting holes of the U bracket the capacitor is mounted. Or making a new bracket to align the shafts. Walt Cates, WD0GOF

The ball bearings fell out. That allowed all the plates to touch. Someone continued to operate it that way and burned up some plates. Even with new balls and adjustment of the end stop, all the plates

Did all the moveable plates shift sideways, causing the gap in one direction to be much smaller than the other?? If yes, can you momentarily make the gap even by tugging (hard) on the shaft?? I had

Are there any other models that use the same cap? I have a HT-37 complete that I will likely part out, as I can't find any one that pill pay $100 for it. Maybe they use the same cap?

C, You are in a tough spot. It hurts. Here is my 2 cents of hogwash on the topic. If I had that situation, I would want to restore it: beg for a real SR2000 cap , perhaps from a total basket case, or

Do you know anyone with a 3D printer that could print you some gears? TomW3TA

Even better, I like the idea of two small pulleys and either a dial cord or "o" ring ala Heathkit HW or SB series.I would be happy to send you two small heathkit pulleys that fit a 1/4 in shaft if you

Good choice in VTVMs, and the input probe mod.I like the Heathkit VTVM "DSB" line, in fact I was looking for an IM-28 when I was shopping for a VTVM. BTW...?Bob Eckweiler (AF6C)?wrote a very

( https://antiqueradio.org/halli09.htm ) Your Heathkit IG-5282 audio signal generator is very basic with limited attenuation ability. Suggest you read Phil’s Old Radios post at

That might work Don. ________________________________ Sent: Thursday, April 4, 2024 8:55 AM To: [email protected] <[email protected]> Subject: Re: [HallicraftersRadios] SR2000

How about a piece of 1/2 plastic rod, drill a 1/4" hole down the middle, slice off a couple sections and sleeve them on to the two shafts. Then run an O ring as a belt like Heathkit did on the HW 101?

NO ? inch. They would have to be machined out. Also NO double joints. So I would have to run two back-to-back to make the JOG. Remember, the shaft is 1 inch DOWN and about an inch OVER. If I had

Thanks Bob. I already purchased the ball bearings and installed them into the race. The cap has warped plates and makes heavy contact. There is no way I can think of to repair it. I spent hours

How about these? You would still need your insulated coupling in the string. C$2.83 70%OFF | Rc Boat Car Metal Cardan Joint 2mm/2.3mm/3mm/3.175mm/4mm/5mm/6mm/8mm Gimbal Couplings Shaft Motor Connector

Good Morning, Thought I would add my 2 cents worth... Since it looks like there is a shaft extender on the cap, that does give you a little bit of room to work with. If it were me, I would look for a

The trimmer is cracked.? ?I could not see this with my eyes. But using my camera you can see the mica?? Layer cracked.