开云体育

Hello Harke, What setup did you use in your comparison of the power sensors? 1) Signal generator connected to the input port 1 of the 11667B and port 2 of the splitter connected to a power sensor used

Hi Harke Sorry I am not good with computer lineages but I hope to use lab view with a friends help I have heard of python script but is new to me so perhaps you could PM me and give me a bit of a

Hi Christian. strange? I recently placed an order and received the link within hours on the Mon 19/05/2025 ordered approx? 14:00 received the link at 20:27 but watch out the incoming Mail was

Hello Paul, I did something like that a couple of years ago, in coax. A HP438A power meter, a HP1667B splitter and a HP8673B generator will do the job. I compared two HP8485 sensors. All GPIB

Hi all as I am after a bit of advice I want to compare power sensors up to 26 Ghz and there appear to be more than one Type of power divider available so looking for guidance to the one I should

Hi everybody. On May 17th, I ordered on the Artekmanuals website, and paid with Paypal 25$, the 8643A CLIP with electronic delivery but nothing was sent. So far, I emailed twice to the official email

Hi again Harke. Understood, but as before, are they all proven working with other known good GPIB instruments? You do know, that you can put the AR488 devices into a "listen only" mode, and use them

Hi Harke , the GPIB talk error message is displayed by the instrument or the by the SW ? The instruments goes in Talk mode ? My suggestion is to check the configuration of the string terminator of the

I upgraded the motherboard in my 16903A a couple of years ago, and it was a HUGE improvement overall of the instrument. It feels zippy and fast, and modern now. I mostly followed the guidance of that

After quite a bit of experimenting and poking around in various sections, I'm convinced that the frequency alignment of the YTO and YTX are OK, and the real problem is loss of conversion gain somehow

Fellow techies, ??? I recently became the new owner of a 16903A logic analyzer. From what I've read, on EEVBlog, it's possible to upgrade the motherboard within a specific range (limited by which

I'm sorry to be asking this question as I imagine it's been answered before but here goes. I'm trying to remote access my 16702B analyzer (Opt 3) from my windows laptop.? The maddning thing is that I

Dave, I have several: Prologix, AR488 and HP85327(?). I used them all with same or similar result. In this case the Prologix adapter is most appropriate. The GPIB status leds on the analyzer lit

"norbinz via groups.io" <norbinz@...> writes: Ok. You're correct - the custom video mode is written to Flash. I reverse engineered the format for the Visualize FX cards many years ago,

Hi. What are you using (HW & SW) as the bus controler? Does it work OK with other instruments etc? Regards. Dave B.

I had a problem with one of mine where one of the switches wasn't popping all of the way out. I don't recall if I managed to just exercise it a bit too recover or I sprayed it with a bit of contact

Yes, my analyzer has option 003. It can output 1600x1200 at 75 Hz, but that's too fast for (probably all) 1600x1200 LCD monitors. My old ViewSonic VP201b almost works, but jitters. I've already tried

The power transformer in my HP 8970A noise figure analyzer was DOA (internal short circuit). I'm using a patchwork of external DC supplies to operate it currently, however, I'm pretty sure that

"norbinz via groups.io" <norbinz@...> writes: It's PA-RISC I/O space. All of the peripherals and Firmware (PDC) are located there. Does your LA have Option 003? If not, there's not

blast.. wrong key "I did buy a number of HP items from Patricia. It is all from an estate sale